Subscribe

ADJACENCIES · July 17, 2026

Gutter Screws: Types, Sizes, and Which to Use

Gutter screws by type, size, and material: hex-head, zip, and hanger screws, what length your fascia needs, and why they beat spikes.

By The Roofing Brief Team. Last reviewed: October 2026.

Gutter screws come in two working sizes. The hidden hanger screw that holds the gutter to the fascia is a #10 x 1-1/2 inch hex washer head screw with a 1/4 inch drive, and the zip screw that joins downspouts, elbows and outlets is a #8 x 1/2 inch self-piercing screw. Gutter fastener maker Raytec Manufacturing lists both as stock items (BSS 912.1 and BSS 804.1 in 410 stainless), plus #10 x 2 inch and #10 x 2-1/2 inch screws for thicker fascia. Pick the length by the fascia behind the gutter and the metal by the gutter itself.

What screws do gutter installers actually use?

Installers use hex-head hanger screws for hidden hangers and self-piercing zip screws for connections. Amerimax’s Installing Metal Gutter Systems sheet tells DIYers to “power drive 1/4 in. hex head screw into fascia board” for its Hidden Hanger with Screw, and to “use sheet metal screws to secure downspouts and elbows.” The table below lists the sizes Raytec stocks for each job.

Screw type Typical size Head/drive Example part (Raytec catalog) Job it does
Hidden hanger screw #10 x 1-1/2″ (also #12 x 1-1/2″) Tall 1/4″ hex washer head BSS 912.1 (410 stainless), BSZ 912.1 (zinc), BSS S912.1 (300 stainless) Hangs the gutter into fascia
Long hanger screw #10 x 2″ or #10 x 2-1/2″ Tall 1/4″ hex washer head BSZ 916.1 (2″), BSS 924.1 (2-1/2″) Wrapped or 2x fascia, reaching framing
Zip / sheet metal screw #8 x 1/2″ (also #6 x 3/8″) 1/4″ hex washer head, self-piercing BSS 804.1, BSZ 804.1, BSB 804.9 (brass) Joins sections, elbows, and outlets
Downspout band screw #8 x 1/2″ into the strap, longer fastener into the wall 1/4″ hex BSS 804.1 for the strap Fixes downspout bands; Amerimax specifies 2 bands per 10 ft section
Spike replacement screw 7″ to 8″ through a ferrule Hex Sold as “8 in. gutter screw” by Gutterworks Reuses the ferrule but replaces the old spike

The old spike-and-ferrule system used a smooth 7 inch aluminum spike, not a screw. That is the fastener most people are replacing when they search for gutter screws, because a smooth shank relies on friction while a threaded screw is locked into the wood fiber. Amerimax still lists “Screw or Spike and Ferrule” as interchangeable parts, so an 8 inch gutter screw drops straight into an existing ferrule.

Gutter screw sizes: what length for your fascia

Screw length is set by the fascia behind the gutter, not by the gutter itself. Nominal 1x fascia is 3/4 inch thick and nominal 2x is 1-1/2 inch thick once dressed, per the American Softwood Lumber Standard (PS 20, administered by ALSC). Subtract the fascia, any aluminum wrap and the gutter back from the screw length to see how much thread reaches solid wood or framing.

If the fascia or target is Use this screw Worked check
1x wood fascia (3/4″ dressed), 5″ aluminum gutter #10 x 1-1/2″ About 3/4″ of thread passes through the back of a 3/4″ board
Aluminum-wrapped 1x fascia #10 x 2″ The wrap, sealant and any shim add depth before wood starts, so the extra 1/2″ keeps full thread in the board
2x fascia (1-1/2″ dressed) or a rafter tail #10 x 2-1/2″ or #12 x 2-1/2″ A 1-1/2″ screw would end flush with the back of a 2x board; 2-1/2″ leaves about 1″ past it
Composite or PVC fascia Length to reach wood framing Follow the fascia maker’s fastening instructions and reach the wood framing behind the board
Section joints, elbows, outlets #8 x 1/2″ or #6 x 3/8″ zip Short enough that the tip barely enters the water channel

Retail packs sell gutter screws in 1/2, 1-1/4, 1-1/2, 2 and 3-1/2 inch lengths. A 1-1/4 inch screw on wrapped fascia leaves under 1/2 inch of thread in the board once the wrap and gutter back are subtracted, which is where many sagging gutters trace back to. When in doubt, step up to the #10 x 2 inch and aim for a rafter tail.

Are gutter screws better than spikes or nails?

Yes, for holding power. A smooth spike holds by friction alone, so wood shrinkage and swelling through wet and dry seasons can walk it back out of the hole, while a threaded #10 screw is mechanically locked into the wood. The Amerimax sheet lists a Hidden Hanger with Screw as the default, with the roof-strap hanger reserved for houses with no fascia board.

Fastener How it holds Spacing per Amerimax Failure mode
Spike and ferrule Friction of a smooth 7″ shank Every 24″, 18″ in heavy ice and snow areas Backs out, gutter sags and pulls away
Screw and hidden hanger #10 threads locked in wood Every 24″, 18″ in heavy ice and snow areas Fails mainly when the fascia rots
Roof-strap hanger Nails under the shingles Only where there is no fascia board Nail holes under shingles can leak

There is a mechanical reason beyond thread grip. A hidden hanger clips under the front lip at about 5 inches out on a 5 inch gutter, so a full trough loads the hanger as a lever that pulls the back screw outward. A threaded #10 screw resists that pull through its thread; a smooth spike resists it only through friction.

Screw material: match the metal to your gutter

Match the screw metal to the gutter metal, or the fastener becomes the first thing to corrode. Raytec rates its yellow zinc-plated gutter screws at 200 hours of salt spray and its Rezist-coated screws at 1,000 hours, and also sells 410 stainless, non-magnetic 300 stainless and brass. Copper is the strict case: the Copper Development Association’s Copper in Architecture Design Handbook says fasteners “should be of galvanically compatible metals, such as copper, copper alloys, like brass or bronze or neutral stainless steel alloy.” Flashing follows the same logic, covered in our guide to nails for flashing.

Gutter metal Use these screws Avoid Source
Aluminum 410 or 300 stainless, coated (Rezist type) or painted zinc made for aluminum Bare carbon steel Raytec catalog; GutterSupply sells painted zinc zip screws “for aluminum”
Copper Copper, brass, bronze or 300 series stainless; copper rivets on seams Zinc-plated steel, aluminum CDA handbook
Galvanized steel Zinc-plated, hot-dip galvanized or stainless Bare carbon steel Raytec catalog
Vinyl Stainless or coated screws through the bracket Nothing galvanic; follow the vinyl maker’s bracket spacing Maker instructions

300 series stainless (Raytec BSS S912.1) is the safe default across aluminum, steel, copper and vinyl. Raytec’s 410 stainless screws are magnetic, which makes them easier to hold on a driver bit, while its 300 series screw is listed as non-magnetic. GutterSupply recommends “copper stainless steel or plain stainless steel zip screws” for copper gutters. For any exposed screw, Raytec’s bonded-washer versions (BSS 913.1, BSZ 913.1) seal the hole, though Raytec marks them “not for roofing.”

Where the screw goes: fascia, rafter tail, or downspout

A gutter system has three fastening points, and each takes a different screw. The #10 x 1-1/2 inch hanger screw goes through the gutter back into the fascia or rafter tail. The #8 x 1/2 inch zip screw joins the gutter to elbows and outlets. The band screw fixes the downspout strap to the wall.

  1. Hidden hangers into the fascia. Space them every 24 inches, or every 18 inches in heavy ice and snow areas, per the Amerimax sheet. Set the gutter on a string line dropped about 1/4 inch per 10 feet toward the downspout before driving screws.
  2. Rafter tails for maximum hold. Rafters usually sit at 16 or 24 inches on center; where a hanger lands on one, a #10 x 2-1/2 inch screw reaches past the fascia into the tail. This matters on heavy 6 inch or copper gutters.
  3. Zip screws at every joint. Two #8 x 1/2 inch zip screws on opposite faces lock each outlet and elbow joint. A 1/2 inch screw keeps the tip from projecting deep into the water channel.
  4. Downspout bands to the wall. Amerimax specifies 2 bands per 10 ft downspout section, fastened with nails or screws; on masonry, use a masonry anchor rated for the wall.

Zip screws for downspouts and elbows

Zip screws are short self-piercing sheet metal screws, #8 x 1/2 inch or #6 x 3/8 inch, that fasten light gutter connections without a pilot hole. Raytec describes all of its gutter screws as “magnetic, self-piercing, 1/4 inch, hex washer heads,” so one 1/4 inch nut driver covers both zip and hanger screws. GutterSupply lists zip screws for “fasten downspouts and elbows together” and long zip screws for “fastening gutter hangers to fascia.”

The rule with zip screws on downspouts: keep them short and on the side faces. A tip that projects into the 2×3 or 3×4 inch downspout interior snags leaves and starts clogs, which is why Alsco Metals notes elbows can be attached with screws or pop rivets. On the gutter trough itself, keep zip screws above the water line.

Rivets or screws for gutters?

Use screws where you may need to take a joint apart and rivets where you want a permanent, low-profile joint. A #8 x 1/2 inch zip screw goes in with a 1/4 inch nut driver and backs out for repairs; a pop rivet needs a pre-drilled hole and a rivet tool and must be drilled out to remove. Our downspout repair guide shows where those screws go when re-seating a leaking joint or reattaching a fallen run. Copper gutter seams are riveted and soldered, which is why the CDA handbook pairs copper rivets with copper systems.

Situation Choose Why
Downspout and elbow joints on aluminum or steel #8 x 1/2″ zip screw Fast, removable for clog clearing
Visible downspout face where screw heads look untidy Pop rivet (aluminum on aluminum) Flush head, no tip in the pipe
Copper seams and outlets Copper rivets plus solder CDA lists copper and copper alloys as compatible fasteners
Hanging the gutter #10 x 1-1/2″ to 2-1/2″ screw, never a rivet Hangers must anchor into wood

Common gutter screw mistakes

Most gutter screw failures trace back to length, metal, or placement, the same three variables that decide every fastener choice on the system.

  • Screw too short for wrapped fascia. A 1-1/4 inch screw grips only the aluminum wrap and part of a 3/4 inch board; it lets go under a full gutter. Wrapped fascia needs #10 x 2 inch.
  • Bare carbon steel in aluminum or copper. Use stainless, coated or painted zinc for aluminum and the CDA-listed metals for copper.
  • Reusing old spike holes. The wallowed-out hole gives a new screw nothing to bite. Drill a fresh hole 1 inch to the side, into solid wood or a rafter tail.
  • Overdriving into thin aluminum. Cranking a screw past snug strips the hole in soft aluminum or splits a hanger. Set the driver clutch and stop when the 1/4 inch washer head seats.

For hanger styles by climate, see our guide to gutter clips and hangers. For a new system, the rain gutter installation guide covers pitch and hanger layout, and how fascia and gutters connect explains why the board behind the screw decides everything. The gutter parts diagram names each component, and our learn hub collects the rest of the gutter series.

Frequently asked questions

What screws do you use for gutters?

Use two types. A #10 x 1-1/2 inch hex washer head screw with a 1/4 inch drive hangs the gutter through a hidden hanger into the fascia; step up to #10 x 2 or 2-1/2 inch on wrapped or 2x fascia. A #8 x 1/2 inch self-piercing zip screw joins sections, elbows and downspout bands. Choose 300 series stainless as a safe default, and follow the Copper Development Association list for copper gutters.

What size screws for gutter hangers?

Size the screw to the fascia. A 3/4 inch thick 1x wood fascia takes a #10 x 1-1/2 inch hanger screw, the standard size in Raytec’s catalog. Aluminum-wrapped 1x fascia needs #10 x 2 inch. A 1-1/2 inch thick 2x fascia or a rafter tail needs #10 or #12 x 2-1/2 inch. A 1-1/4 inch screw is often too short on wrapped fascia.

Are gutter screws better than spikes?

Yes, for holding power. A smooth 7 inch spike holds by friction and can work loose as the wood shrinks and swells, while a threaded #10 screw locks into the wood fiber. Amerimax lists the screw-type Hidden Hanger as its standard fascia fastener at one hanger every 24 inches, or every 18 inches in heavy ice and snow areas.

Can you use regular screws for gutters?

Only if the metal and length are right. A plain carbon steel deck screw rusts in a wet gutter and can stain or corrode the hole. Use 300 series stainless, 410 stainless or coated gutter screws on aluminum and steel, and copper, brass, bronze or neutral stainless on copper, per the Copper Development Association. Size it #10 x 1-1/2 inch or longer for hangers and #8 x 1/2 inch for joints.

What are zip screws for gutters?

Zip screws are short self-piercing sheet metal screws, #8 x 1/2 inch or #6 x 3/8 inch, that fasten light gutter connections without a pilot hole. They drive with a 1/4 inch nut driver and are the standard for joining downspout sections, elbows and outlets. Keep them on the side faces so the tip does not project into the water channel and snag debris.

Do gutter screws go into the fascia or the rafter?

Either works, but the rafter tail holds better. A #10 x 1-1/2 inch hanger screw into 3/4 inch fascia is the standard for 5 inch aluminum gutters. For heavy 6 inch or copper gutters, or in heavy snow areas where Amerimax tightens hanger spacing to 18 inches, use a #10 x 2-1/2 inch screw that reaches the rafter tail behind the fascia, usually 16 or 24 inches on center.