To clean a clogged gutter, first find where the blockage sits, then match the method to it. A trough packed with wet leaves clears fastest by hand from a ladder with a gutter scoop, followed by a hose rinse toward the downspout. A blocked downspout needs a hose blast from the top and, if that fails, a hand auger fed from the bottom. Ground tools unclog gutters with light debris on a single story. For scale, HomeGuide reports that a professional crew takes 30 to 90 minutes to clean a typical home’s 150 to 200 linear feet of gutter, and up to 4 hours on large multi-story homes.
By The Roofing Brief Team (masthead). Last reviewed: October 2026.
Separate a gutter clog (debris in the horizontal trough) from a downspout clog (debris jammed in the vertical pipe or elbow) before you climb, because the two need different tools. HomeGuide prices them separately too: whole-house cleaning at $100 to $250, and clearing clogged downspouts at $60 to $150.
How do you know a gutter is clogged and where?
A clogged gutter announces itself during rain: water spills over the front lip in a sheet instead of draining, or runs down behind the gutter and stains the fascia. Between storms, HomeGuide’s checklist of signs includes sagging gutters, stains along the siding, plants growing in the trough, animals nesting, icicle buildup in winter, and no cleaning for more than 1 year. Where the water misbehaves tells you where the clog is. Use the table below before you set up a ladder.
| What you see | Likely clog location | First method to try |
|---|---|---|
| Water sheets over the front edge along the whole run | Trough packed with debris | Hand-scoop from a ladder, then hose rinse |
| Water pools at one section, drains slowly elsewhere | Localized trough blockage near a seam or corner | Scoop that section, flush toward the downspout |
| Trough looks clean but water backs up and overflows near the outlet | Downspout or elbow clog | Hose blast down the downspout, then hand auger |
| Downspout stays dry during heavy rain | Full blockage upstream in the downspout | Tap the pipe to find the plug, auger from below |
| Water runs behind the gutter onto the fascia | Missing drip edge or a trough overflowing from a clog | Clear the clog first, then check flashing |
If water sheets over the front but the downspout runs freely once you flush it, the problem was the trough. If the trough is clean and water still backs up, the pipe is the culprit. A drip edge is required at the eaves and rakes of shingle roofs under IRC R905.2.8.5; our guide to water going behind the gutter covers the flashing side of that last symptom, which a cleaning alone will not fix.
What tools do you need to clean a clogged gutter?
You need a way to reach the gutter, a way to lift debris out, and a way to flush what is left. For most single-story and two-story homes that means a stable extension ladder, a gutter scoop, thick gloves, eye protection, and a garden hose with a pressure nozzle. Pick an extension ladder whose duty rating covers your weight plus tools: Type I is rated for 250 pounds and Type IA for 300 pounds, per the American Ladder Institute. A downspout clog adds a hand auger or plumber’s snake. Ground-only jobs swap the ladder for a telescoping wand, leaf blower attachment, or wet/dry vacuum.
- Extension ladder: long enough to set at a 1-in-4 angle and still reach the eave; when a ladder is used to reach an upper landing, OSHA 1926.1053(b)(1) requires the rails to extend at least 3 feet above it.
- Gutter scoop or narrow trowel: a plastic scoop matches the trough profile and will not gouge aluminum.
- Thick gloves and ANSI Z87.1-marked safety glasses: wet debris hides screws, shingle grit, and the occasional animal.
- Garden hose with a high-pressure nozzle: for the final flush and for testing the downspout.
- Hand auger or plumber’s snake: only needed when a downspout stays blocked after a hose blast.
- Ground option: a telescoping gutter wand, a leaf-blower gutter kit, or a wet/dry vacuum with a curved attachment.
- Bucket or tarp: a bucket clipped to the ladder or a tarp below keeps debris off the beds and speeds cleanup.
Compare reach tools in our guides to gutter cleaning tools you can use from the ground and the gutter cleaning pole.
How to clean a clogged gutter trough, step by step
Cleaning a clogged trough is a five-step job: set the ladder, scoop the debris toward yourself, work in sections, flush with a hose, and confirm the water drains. Working in arm’s-length sections and moving the ladder often keeps your weight between the rails. HomeGuide’s 30 to 90 minutes is for a professional crew on a whole house; budget more for a first DIY run with ladder moves.
- Set the ladder safely. Place it on firm, level ground with the base out from the wall by one-quarter of the working length, the ratio in OSHA 1926.1053(b)(5)(i). For a 16-foot working length, that is 4 feet out. Keep three points of contact and never lean past the rails.
- Scoop toward yourself. Lift wet leaves and grit into a bucket hooked to the ladder, starting at the downspout end so loosened debris does not wash into the outlet.
- Move the ladder, do not reach. Keep your belt buckle between the rails and stay off the top 3 rungs of an extension ladder, per the American Ladder Institute; reposition instead of stretching.
- Flush toward the downspout. Run the hose from the far end so water carries fine grit to the outlet.
- Confirm drainage. Water should exit the downspout in a steady stream. If it backs up in the trough, the clog moved into the downspout.
How to unclog a gutter downspout
Unclog a downspout by flushing from the top first, then augering from the bottom if the flush fails. Feed a hose into the top opening at full pressure to push the plug out the bottom. If water backs up instead of clearing, disconnect the lower elbow, feed a hand auger up from the bottom, turn clockwise to break the compaction, then flush again. Residential downspouts are commonly 2×3-inch or 3×4-inch rectangular pipe, so check that the auger cable passes the elbows of your size.
- Test with a hose from the top. Run the nozzle at full pressure into the top opening. A loose clog blasts out the bottom.
- Locate the plug by tapping. Knock along the pipe; a dull, solid sound marks the packed debris, often at an elbow.
- Open the bottom elbow. Remove the sheet-metal screws or clip holding the lower elbow or extension so you can work the clog from below.
- Auger from the bottom. Feed a hand auger up the pipe, turning the drum clockwise to break the compaction. Wear eye protection; debris sprays back.
- Flush and reassemble. Once the auger passes through, run the hose again from the top to clear residue, then reconnect the elbow and add a splash block or extension. Where expansive or collapsible soils exist, IRC R801.3 calls for roof water to discharge at least 5 feet from the foundation.
Downspout clogs pack tighter than trough clogs, which is why HomeGuide lists clearing them as a separate $60 to $150 line. Our dedicated walkthrough of the gutter snake and how to unclog a downspout covers auger sizing and stubborn underground-drain blockages in more detail.
Can you clean a clogged gutter from the ground?
Yes, light debris on a single-story home clears from the ground with a telescoping wand, a leaf-blower gutter kit, or a wet/dry vacuum with a curved attachment. Ground methods trade thoroughness for safety: they move loose, dry leaves well but struggle with wet, compacted mats. For a packed trough on a two-story home, HomeGuide’s $100 to $275 professional range is the alternative to ladder work.
| Method | Best for | Practical reach | Main limitation |
|---|---|---|---|
| Hand scoop from ladder | Wet, compacted debris | Any height with the right ladder | Requires ladder work |
| Telescoping gutter wand (hose) | Loose leaves and grit | Up to about a second story | Weak on packed mats; you cannot see the trough |
| Leaf-blower gutter kit | Dry, loose debris | Single to second story | Useless on wet debris; messy |
| Wet/dry vacuum with wand | Damp grit and small debris | Single story reliably | Slow; frequent tank emptying |
| Gutter tongs on a pole | Grabbing chunky clumps | Single to second story | Fiddly; low visibility |
Whatever the method, wear ANSI Z87.1-marked eye protection: from the ground you are aiming debris and water back toward your own face. If a ladder is unavoidable on a taller home, our guide to choosing a ladder for gutter cleaning covers stabilizers and standoffs that keep the rails off the gutter.
Why clearing a clogged gutter matters: the water-weight math
A clogged gutter is not just an overflow nuisance. Water weighs about 62.4 pounds per cubic foot near 40°F, per the USGS Water Science School, which works out to about 8.34 pounds per gallon. A blocked trough holds that water against the hangers and fascia, and the overflow it forces attacks the roof edge and foundation.
You can compute the load from one measurement: the water-filled cross-section of your trough in square inches (width times water depth, roughly). Each square inch of cross-section holds 12 cubic inches per foot of run, which is 0.433 pounds of water per foot (12 x 62.4 / 1,728). Soaked leaves add more on top.
| If the water cross-section is | Water per foot | 40-foot run, full | Calculation |
|---|---|---|---|
| 8 sq in | 3.5 lb | 139 lb | 8 x 0.433 x 40 |
| 10 sq in | 4.3 lb | 173 lb | 10 x 0.433 x 40 |
| 12 sq in | 5.2 lb | 208 lb | 12 x 0.433 x 40 |
Downstream, overflow that runs behind the gutter or pools at the foundation is what turns a $100 to $250 cleaning into a fascia or gutter replacement: HomeGuide puts installed aluminum gutters at $600 to $1,800 for 150 linear feet. Clogged gutters are also linked to ice dams in cold climates. The wet-debris connection to residential roof maintenance is why gutter clearing sits on every seasonal checklist.
How often should you clean gutters to prevent clogs?
Most gutters and downspouts need cleaning 2 to 3 times a year, or before the rainiest season, depending on climate and nearby trees, per HomeGuide’s gutter cleaning guide. Homes ringed by mature trees, especially pines that shed needles year-round, sit at the top of that range or above it, and even guarded gutters need cleaning about every 2 years. HomeGuide notes spring and late fall are peak season, so booking in early winter or midsummer is faster and cheaper. Match the schedule to your tree cover, not the calendar alone.
| If the tree cover is | Cleanings per year | Best timing |
|---|---|---|
| Few or no overhanging trees | 1 to 2 | Late fall |
| Some deciduous trees nearby | 2 | Late spring and late fall |
| Heavy tree cover or pines | 3 or more | Spring, mid-summer, and twice in fall |
| Gutter guards installed | About every 2 years (HomeGuide), more under heavy trees | Late fall |
Gutter guards reduce how often the trough packs with leaves, but they do not eliminate cleaning: HomeGuide says guarded systems still need cleaning about every 2 years because small particles pass through. Weigh that trade-off in our analysis of whether gutter guards are worth it before assuming they end the chore.
What does professional gutter cleaning cost in 2026?
Professional gutter cleaning costs $100 to $250 on average, or $0.50 to $2.50 per linear foot, per HomeGuide’s November 2025 guide, which assumes 150 to 200 linear feet. Price scales with stories: $70 to $200 for a one-story home, $100 to $275 for two stories, and $130 to $400 for three or more. Clearing clogged downspouts adds $60 to $150.
| Service | Typical range | Source |
|---|---|---|
| Single-story gutter cleaning (150 to 200 LF) | $70 to $200 | HomeGuide, Nov 2025 |
| Two-story gutter cleaning | $100 to $275 | HomeGuide, Nov 2025 |
| Three stories or more | $130 to $400 | HomeGuide, Nov 2025 |
| Clearing clogged downspouts | $60 to $150 | HomeGuide, Nov 2025 |
| Per linear foot | $0.50 to $2.50 | HomeGuide, Nov 2025 |
| New aluminum gutters if neglect forces replacement (150 LF) | $600 to $1,800 installed | HomeGuide aluminum gutters |
For a 180 LF two-story home, the per-foot range works out to $90 to $450, so ask each quote for its per-foot rate and whether downspout clearing is included. For a fuller schedule-and-price breakdown, see our guide to gutter cleaning cost and schedule. DIY clearing costs only your time plus a scoop and a hose you likely already own.
Frequently asked questions
How do you clean a badly clogged gutter?
Clear a badly clogged gutter by hand from a ladder rather than with water first. Scoop the wet, compacted debris into a bucket working toward the downspout, then flush the trough with a hose from the far end. If the downspout backs up, blast it from the top and auger it from the bottom. Water alone rarely moves a heavy, packed mat. If you hire it out, HomeGuide puts gutter plus clogged-downspout cleaning at $160 to $400.
How do you unclog a gutter without a ladder?
Unclog a gutter without a ladder using a telescoping gutter wand attached to a hose, a leaf-blower gutter kit, or a wet/dry vacuum with a curved attachment. These reach a single-story eave and clear loose leaves and grit well. Wear eye protection, since you are directing debris and water back toward yourself. Wet, packed debris often still requires a ladder; HomeGuide prices a one-story professional cleaning at $70 to $200.
How often should gutters be cleaned?
Most gutters and downspouts need cleaning 2 to 3 times a year, or before the rainiest season, per HomeGuide. Homes with heavy tree cover or pine needles sit at the top of that range, while homes with few overhanging trees may need only one cleaning. Gutters with guards still need cleaning about every 2 years.
What happens if you never clean your gutters?
Neglected gutters overflow, letting water rot the fascia and soffit, seep into walls and basements, and pool at the foundation. In cold climates, trapped water can feed ice dams. Standing water weighs 8.34 pounds per gallon, so a full trough loads its hangers. Replacing 150 feet of aluminum gutter runs $600 to $1,800 installed per HomeGuide, far more than a $100 to $250 cleaning.
Can I use a pressure washer to clean gutters?
A pressure washer can clear a gutter, but use it with caution. High pressure can dent 0.027-inch residential aluminum (HomeGuide’s typical gutter thickness), drive water behind the gutter, and lift shingles at the roof edge if aimed upward. A garden hose with a pressure nozzle is safer for the trough and the downspout in most cases. Reserve pressure washing for exterior gutter faces or stubborn buildup, and keep the spray angled away from the roof.
How do I know if my downspout is clogged or my gutter?
If water sheets over the front of the trough along the whole run, the gutter itself is packed. If the trough looks clean but water backs up and overflows near the outlet, the downspout is clogged. Tap the downspout: a dull, solid sound marks where debris is packed, often at an elbow. A downspout that stays dry during heavy rain signals a full blockage upstream in the 2×3-inch or 3×4-inch pipe.
Cost and frequency figures are published planning ranges from HomeGuide and vary by region, home size, and contractor.