Subscribe

ADJACENCIES · July 11, 2026

Metal Roofing Insulation Underlayment: What Goes Where

Metal roofing insulation underlayment: double bubble is about R-1 alone, polyiso R-5.7/in, radiant barriers need a 1/2 to 3/4 in air gap. Costs and code.

Reviewed by The Roofing Brief Team. Last reviewed: October 2026.

Metal roofing insulation underlayment is really two jobs stacked in one part of the roof: a water-shedding underlayment that keeps moisture off the deck, and a thermal layer (radiant barrier foil, double-bubble reflective insulation, rigid foam board, or batts) that controls heat and condensation. The numbers that separate them: a double-bubble roll is about R-1 on its own, per reflective insulation maker RadiantGuard, while 1 inch of polyiso board is R-5.7 on the Hunter H-Shield data sheet.

Metal roofing insulation underlayment: the two layers people confuse

Underlayment and insulation are not the same layer. Underlayment is a thin water barrier (synthetic, felt, or self-adhering high-temp membrane to ASTM D1970) laid on the deck to shed moisture and protect the sheathing; IRC R905.1.1 lists the approved types by roof covering. Insulation controls heat flow and is rated by R-value. Some products, like double-bubble reflective rolls and foil-faced “radiant barrier underlayment,” try to do both, but the foil and bubble layer itself adds only about R-1.

The water-shedding side is a separate topic with its own product classes and code rules. Our guide to metal roof underlayment (felt, synthetic, and high-temp) covers that water layer in depth. The rest of this page stays on the thermal layer: what insulates a metal roof, what reflects heat, and how to stop condensation.

Do you need insulation under a metal roof?

Over a conditioned space, yes. Metal conducts heat quickly and the panel underside cools fast on clear nights, so bare panels over a heated or cooled room drive high energy bills and condensation. Over an unconditioned shed or carport, insulation is optional, though a condensation-control layer still earns its keep: HomeGuide’s metal building insulation guide (November 2025) recommends housewrap between the metal and the insulation to stop condensation and drafts.

Building energy code sets the target for living space. The 2021 IECC ceiling values, mirrored in ENERGY STAR’s insulation table, are R-30 in climate zone 1, R-49 in zones 2 and 3, and R-60 in zones 4 through 8. A metal panel and a reflective sheet alone do not meet that number, which is why insulation sits alongside, not instead of, the underlayment.

Insulation options under a metal roof, compared

Five layers compete for the space under metal panels: radiant barrier foil, double-bubble reflective insulation, rigid foam board (polyiso or XPS), fiberglass or mineral wool batts, and closed-cell spray foam. They differ sharply in R-value per inch, whether they need an air gap, and cost, from $0.30 per square foot installed for a radiant barrier to $5.00 for closed-cell foam in HomeGuide’s ranges. A sixth option, used mostly on commercial and cold-storage buildings, skips the layered stack entirely: insulated metal panels with a built-in foam core.

Layer R-value Needs air gap? Best use Typical cost Source
Radiant barrier foil Near R-0 itself; works by low emittance (0.04 per Radiant Barrier US’s ASTM C1371 test) Yes: 1/2 in minimum per RoofingFoil; 3/4 in is the common rating basis Hot climates, attic or over-deck $0.10 to $0.60/sq ft material; $0.30 to $2.00 installed HomeGuide (Sept 2023); RoofingFoil
Double-bubble reflective (foil/bubble/foil) About R-1 alone; R-7.95 heat flow down, R-4.05 up, facing an enclosed air space Yes, for the higher figures Pole barns, condensation control $0.30 to $0.80/sq ft material; $0.50 to $2.20 installed RadiantGuard; Radiant Barrier US (ASTM C1224); HomeGuide
Rigid foam board, polyiso R-5.7 per inch LTTR (R-11.4 at 2 in, R-23.6 at 4 in) No Continuous above-deck insulation $1.20 to $3.70/sq ft installed (foam board) Hunter H-Shield TDS (ASTM C1289); HomeGuide (Nov 2025)
Rigid foam board, XPS R-5 per inch No Above-deck, damp locations $1.20 to $3.70/sq ft installed (foam board) Owens Corning FOAMULAR 250 data sheet; HomeGuide
Fiberglass or mineral wool batts R-2.2 to R-2.9 per inch (fiberglass); R-3.2 to R-4.1 (mineral wool) No Between rafters or purlins $0.80 to $2.60/sq ft installed HomeGuide (Nov and Dec 2025)
Closed-cell spray foam R-5 to R-7 per inch No Underside of deck, seals and insulates $3.00 to $5.00/sq ft installed; $1.30 to $2.90 per board foot on metal buildings HomeGuide (Nov and Dec 2025)

How a radiant barrier works, and why the air gap matters

A radiant barrier is aluminum foil that reflects radiant heat instead of absorbing and re-emitting it: Fi-Foil rates its single-sheet attic barrier at up to 95 percent of radiant heat transfer and RoofingFoil claims up to 97 percent. It only works facing an air space. Pressed flat against the panel back with no gap, it simply conducts heat and loses most of its value. A radiant barrier complements R-value insulation; it does not replace it.

  • Face the reflective side toward the air gap. HomeGuide notes one-sided foil suits metal roofs where the foil goes against the deck under battens.
  • Keep the gap with battens or furring strips: RoofingFoil’s metal-roof instructions set a 1/2 inch minimum, and most published reflective R-values assume a 3/4 inch air space.
  • Radiant barriers pay off most in hot, sunny climates: HomeGuide estimates savings of $45 to $90 per year on cooling in hot climates and $12 to $24 in cooler regions.
  • Dust on an up-facing foil surface cuts reflectivity, which is why HomeGuide recommends two-sided foil when the barrier lies over attic floor insulation.

Savings depend heavily on climate zone. Our cool roof energy savings report breaks down how much reflective and cool-roof surfaces return by climate zone.

Where each layer goes: the assembly from deck to panel

On a new over-deck metal roof, the layers stack in a fixed order so water sheds outward and the radiant barrier keeps its air gap. Skipping the battens is the common error that flattens a reflective sheet against the panels and removes the 1/2 to 3/4 inch air space its rating depends on.

  1. Roof deck: OSB or plywood sheathing.
  2. Water-shedding underlayment: synthetic or high-temp self-adhering membrane (ASTM D1970) laid directly on the deck, or a combined foil underlayment such as RoofingFoil + Underlayment, rolled horizontally from the eave and lapped at least 4 to 6 inches per row.
  3. Above-deck insulation, if used: rigid foam board (2 inches of polyiso is R-11.4 on the Hunter H-Shield sheet), or a radiant barrier set up for an air gap.
  4. Furring strips or battens: create the vented air gap of at least 1/2 inch that the radiant barrier needs and give condensation a path to dry.
  5. Metal panels: fastened to the battens or deck.

For a retrofit or an open attic, the thermal layer usually moves under the deck instead: batts between the rafters or closed-cell spray foam on the underside, with a radiant barrier stapled to the rafter faces so it still faces an air space. On a pole barn with no deck, RoofingFoil’s instructions drape the foil over the purlins with about 4 to 6 inches of sag at mid-span to form the air space, fastened with screws or double-sided tape on metal framing.

How to install bubble insulation under metal roofing

  1. Start at the eave. Roll the foil or bubble sheet horizontally across the deck or purlins and work toward the ridge, per RoofingFoil’s metal-roof instructions.
  2. Fasten the edges. Use plastic cap roofing nails on wood (staples only as a backup); on steel purlins use screws or double-sided tape until the panels go on.
  3. Lap every row 4 to 6 inches. If a lap falls under 4 inches, RoofingFoil recommends sealing the seam with foil seam tape.
  4. Build the air gap. Install battens over the foil for a 1/2 inch minimum gap, or let the sheet sag 4 to 6 inches between framing members on a deckless roof.
  5. Install the panels over the battens with the maker’s fastener schedule.

Does insulation under a metal roof stop condensation?

The right layer does; the wrong one traps moisture. Condensation forms when warm indoor air meets the cold metal underside. In an unvented roof, IRC R806.5 requires a minimum R-value of air-impermeable insulation (closed-cell foam or rigid board) in direct contact with the deck to keep it above the dew point: R-5 in zones 1 to 3, R-10 in 4C, R-15 in 4A and 4B, R-20 in zone 5, R-25 in zone 6, R-30 in zone 7 and R-35 in zone 8. A bubble-foil sheet laid tight to the deck with no ventilation can hold water against the sheathing and rot it.

Metal is especially prone to this because the panels cool fast on clear nights. HomeGuide’s metal building guide notes that 2 inches of closed-cell foam acts as an air, vapor and moisture barrier, and Radiant Barrier US lists a vapor permeance of 0.01 perm for its foil/bubble products. Our guide to metal roof condensation walks through the causes and the fixes that actually hold.

If your metal roof is over Use Threshold or source
A conditioned room, new build with a deck Rigid board above the deck plus underlayment Ceiling target R-30 / R-49 / R-60 by zone (2021 IECC via ENERGY STAR)
An unvented cathedral ceiling Closed-cell foam or rigid board at the deck, at least the IRC minimum IRC R806.5: R-5 (zones 1 to 3) up to R-35 (zone 8)
A vented attic in a hot, sunny climate Radiant barrier with a 1/2 to 3/4 in air gap, plus attic floor insulation HomeGuide: $45 to $90 per year cooling savings in hot climates
An unheated pole barn or shed Double-bubble foil with an air gap, or 2 in of closed-cell foam HomeGuide: closed-cell is an air and vapor barrier at 2 in
A heated shop or barn Closed-cell foam at 4 to 5 in on the roof deck, or batts plus a vapor barrier HomeGuide (Nov 2025) recommended thickness
Purlins with no deck Foil draped 4 to 6 in between purlins, then panels RoofingFoil install instructions

R-value and the bubble-foil label trap

Reflective bubble products are often marketed with large R-values such as R-17 or R-22. Under the FTC R-value Rule, 16 CFR 460.5, a multi-sheet reflective product must be tested to ASTM C1363 in a panel built to ASTM C1224, and an R-value that includes an air space applies only when that air space is actually built. The bubble material alone is about R-1. The reflective benefit is real in a hot attic with an air gap, but it does not replace the R-49 to R-60 the 2021 IECC sets for ceilings in zones 2 through 8.

When you compare products, ask for the tested material R-value, the air-space size and the heat-flow direction behind any system figure: Radiant Barrier US’s double bubble drops from R-7.95 with heat flowing down to R-4.05 with heat flowing up. Our insulation R-value chart lists real R-per-inch numbers by material so you can size the layer honestly.

What insulation under a metal roof costs

HomeGuide’s ranges: $0.30 to $2.00 per square foot installed for a radiant barrier and $0.50 to $2.20 for reflective bubble insulation (radiant barrier cost guide), $1.20 to $3.70 for foam board, $0.80 to $2.60 for batts and rolls, and $3.00 to $5.00 for closed-cell spray foam (spray foam cost guide). In hot climates, a radiant barrier paired with attic batts is often the low-cost path. Continuous rigid board above the deck costs more but removes the thermal bridging through rafters.

Project size and timing move these numbers: HomeGuide notes spray foam contractors often set minimum fees of $1,000 to $2,000 or more, and that a whole metal building runs $1.00 to $4.50 per square foot of surface area. Pricing the insulation into a full metal roof quote up front avoids a panel-only bid that leaves the thermal layer out.

Frequently asked questions

Is underlayment the same as insulation on a metal roof?

No. Underlayment is a thin water barrier laid on the deck to shed moisture and protect the sheathing, and it carries almost no R-value. Insulation controls heat flow and is rated by R-value. Reflective bubble rolls marketed as insulated underlayment blur the line, but RadiantGuard puts a typical 1/4 inch double-bubble product at about R-1 on its own, so most roofs need a separate thermal layer.

What is the best insulation to put under a metal roof?

For a new roof with a deck, continuous rigid foam board above the deck gives the most R-value per inch with no thermal bridging: polyiso is R-5.7 per inch on the Hunter H-Shield data sheet and XPS is R-5 per inch on Owens Corning’s FOAMULAR 250 sheet. Closed-cell spray foam (R-5 to R-7 per inch) both seals and insulates in an open attic. In a hot climate, a radiant barrier with a 1/2 to 3/4 inch air gap plus attic batts is often the lowest-cost mix.

Does a radiant barrier need an air gap?

Yes. A radiant barrier reflects heat only when its foil faces an air space. RoofingFoil’s metal-roof instructions set a 1/2 inch minimum, usually created by battens, and most published reflective R-values assume a 3/4 inch space. Pressed flat against the panel back, the foil conducts heat and loses most of its value.

Does insulation under a metal roof stop condensation?

The right layer does. In an unvented roof, IRC R806.5 requires air-impermeable insulation at the deck of at least R-5 in zones 1 to 3, rising to R-35 in zone 8, so the underside stays above the dew point. A vented air gap also lets moisture dry. A bubble-foil sheet laid tight to the deck with no ventilation can trap water against the sheathing and cause rot.

What R-value do I need under a metal roof?

For a conditioned space, the 2021 IECC ceiling values are R-30 in climate zone 1, R-49 in zones 2 and 3, and R-60 in zones 4 through 8, as ENERGY STAR’s table shows. A metal panel and a reflective sheet do not reach that number on their own; the target is met by batts, blown insulation, rigid board, or spray foam.

Does bubble foil insulation really work under metal roofing?

It helps in a specific case: a hot attic or barn where the foil faces a real air gap and blocks radiant heat. Its material R-value is about R-1, so it will not meet code insulation levels by itself. Under 16 CFR 460.5, any higher system R-value must come from an ASTM C1363 hot-box test with the air space included, so check the air-space size and heat-flow direction behind the label.