By The Roofing Brief Team. Last reviewed: October 2026.
Roof mastic is a thick, trowel or brush grade sealant used to waterproof the details on a roof (seams, penetrations, drains, skylights, vents, fasteners and flashing), and the asphalt version is sold to the ASTM D4586 roof cement standard, applied about 1/8 inch thick at roughly 12 sq ft per gallon. Elastomeric versions such as silicone mastic go on thinner and are usually reinforced with polyester fabric as part of a coating restoration system, not as a whole roof by itself. Contractors also call it flashing mastic, detail mastic or roofing tar.
Roof mastic overlaps with roofing cement, sealant and coating, and the label alone will not tell you which job a product does. Tremco’s ELS data sheet, for example, calls the same tub a “roof cement” while specifying it for a 3-course mastic, reinforcement, mastic repair at 25 sq ft per 5-gallon pail.
What is roof mastic?
Roof mastic is a high-viscosity waterproofing compound spread onto roof details to seal them against water. It is too thick to spray, so it goes on with a trowel, brush or caulk gun: JM’s MBR Utility Cement, a trowel-grade asphalt mastic, runs 100,000 to 250,000 cps in summer grade. Modern mastics are elastomeric (acrylic, silicone, butyl or urethane) or asphalt based, and the elastomeric ones list their stretch: Armour Proof’s AP-2400 silicone mastic reports 275 percent elongation.
Asphalt roof mastic and asphalt roof cement share a formula. ASTM D4586 defines asbestos-free asphalt roof cement as an asphalt base, volatile petroleum solvents and mineral or other stabilizers, mixed for trowel application to roofing and flashing. The JM MBR Utility Cement data sheet lists 82 percent solids, 9.5 lb per gallon and under 250 g/L VOC for one such product; the fiber and filler are what let a Type II cement like Tremco ELS hold on a vertical repair without sagging.
| ASTM D4586 grade | What it means | Example product | Source |
|---|---|---|---|
| Type I | Asphalt that is self-healing, adhesive and ductile | JM MBR Utility Cement | ASTM D4586 abstract; JM data sheet |
| Type II | Asphalt with a high softening point and relatively low ductility | Tremco ELS (Type II, Class I) | Tremco data sheet |
| Class I | For essentially dry surfaces | Tremco ELS | ASTM D4586 abstract |
| Class II | For damp, wet or underwater surfaces | Karnak 19 Ultra (Type I, Class I and Class II) | ASTM D4586 abstract; Karnak |
Elastomeric mastics swap the asphalt and solvent for a polymer. The AP-2400 Silicone Mastic data sheet (revised July 6, 2026) lists 95 percent solids by volume, under 50 g/L VOC and a -25°F to 175°F service range, and these white mastics are the type used with silicone and acrylic roof coating types on commercial restoration jobs.
Roof mastic vs roofing cement vs sealant vs coating
The four products run from thickest to thinnest. Mastic and cement are pastes laid about 1/8 inch thick for detail work, sealant is a flexible caulk for joints under 1 inch, and coating is a thin membrane sprayed or rolled over the whole surface. The table below matches each to its repair.
| Product | What it is | Best for | Applied with | Whole-roof? |
|---|---|---|---|---|
| Roof mastic | Thick, often fabric-reinforced elastomeric or asphalt paste | Seams, penetrations, curbs, flashing details inside a coating system | Trowel, brush, bulk gun | No, it is a detail product |
| Roofing cement | Cutback asphalt paste with fillers and fiber (ASTM D4586) | Patching shingles, small holes, bedding flashing | Trowel, caulk gun | No, standalone patch |
| Roof sealant | Silicone, acrylic, or polyurethane caulk | Fastener heads, narrow joints, gaps under 1 inch | Caulk gun | No, standalone |
| Roof coating | Sprayable elastomeric fluid membrane | Restoring an entire low-slope roof surface | Airless sprayer, roller | Yes, the field membrane |
Here is the practical rule the product labels rarely spell out. In ASTM terms the trowel-grade asphalt paste is officially named a roof cement (D4586), not a mastic, so on a shingle roof the two words point at the same tube. In the commercial coating world, mastic means the reinforced detail compound you apply before the field coating, and it is a real, separate step. So the answer to “is mastic the same as cement” depends on which roof you are standing on. For the asphalt version and how to trowel it, see our guide to roofing cement types and application.
Roof mastic product specs from maker data sheets
| Product | Chemistry and standard | Coverage | Application window and cure | Source |
|---|---|---|---|---|
| JM MBR Utility Cement | Asphalt, ASTM D4586 Type I; 82% solids | 8 gal per square (100 sq ft) at 1/8 in | 40°F to 100°F; winter grade below 60°F | JM RS-4168 (9-23) |
| Tremco ELS | Fibrated asphalt, ASTM D4586 Type II, Class I | 12 sq ft/gal at 1/8 in; 25 sq ft per 5 gal in 3-course | Product at 45°F or above; no rain before cure | Tremco ELS data sheet |
| Karnak 19 Ultra | Rubberized asphalt flashing cement, wet/dry | Not stated on product page | Summer, Semi and Winter grades; 10.1 oz to 55 gal | Karnak product page |
| AP-2400 Silicone Mastic | 1-part silicone, 95% solids; 275% elongation | Per gallon: 750 fasteners, or 100 LF of 4 in seam at 40 wet mils | 50°F to 90°F best; max 50 wet mils per pass, min 25 dry mils; cure 12 to 18 h | Armour Proof / United Asphalt TDS (rev. 7.6.26) |
What is roof mastic used for?
Roof mastic seals the spots where a roof is most likely to leak: anywhere the flat field is interrupted. It is not meant to cover open field membrane. Its job is the transitions and the holes, where a sprayed coating alone cannot build enough thickness; AP-2400’s data sheet, for example, requires at least 25 dry mils on a detail.
Typical mastic applications include:
- Penetrations: pipe boots, vents, conduit, and rooftop equipment curbs.
- Seams and splits: lap seams on modified bitumen, splits in aged membrane, and field seams on single-ply.
- Flashing details: base flashing at walls, parapets, and skylight curbs.
- Fasteners and drains: exposed screw heads, drain flanges, and scupper edges.
- Reinforced repairs: embedding polyester fabric over cracks in a three-course patch.
JM states MBR Utility Cement is for built-up and modified bitumen flashing details and is not for single-ply systems, so check the data sheet’s compatibility chart before using an asphalt mastic on TPO, PVC or EPDM. For a broader menu of what stops a leak by product, compare mastic against tapes and patch kits in our rundown of flat roof repair materials and the field guide to roof leak repair products.
Which roof mastic to use: decision table
| If the detail is… | Use | Threshold and source |
|---|---|---|
| Wet, damp or under water right now | ASTM D4586 Class II wet/dry cement, or a silicone mastic rated for wet surfaces | Class II is for damp, wet or underwater surfaces (ASTM D4586); AP-2400 states wet and underwater use |
| Vertical: a wall, curb or parapet base flashing | Type II fibrated cement or flashing-grade mastic | Tremco ELS is Type II and listed for vertical repairs |
| On an asphalt BUR or mod-bit roof | Asphalt mastic | JM MBR Utility Cement: BUR and mod-bit only, not single-ply |
| On a silicone-coated roof | Silicone mastic | AP-2400’s data sheet says it works on roofs previously coated with AP-5200 silicone |
| Being worked below 45°F to 50°F | Winter-grade asphalt mastic | JM: 40°F minimum, winter grade below 60°F; Tremco ELS: product at 45°F or above |
| A crack or split wider than a hairline | 3-course: mastic, polyester fabric, mastic | Tremco ELS: 25 sq ft per 5 gal pail in 3-course work |
| A joint under 1 inch or a fastener head | Sealant or silicone mastic bead | AP-2400: about 750 fasteners per gallon |
Roof mastic grades: brush, butter, and flashing
Mastic comes in different consistencies, and picking the wrong one is a common installer mistake: thin mastic sags off a wall, and thick mastic will not wet out a fabric. Makers publish the difference as viscosity or as seasonal grades; JM’s MBR Utility Cement runs 100,000 to 250,000 cps in summer grade and 50,000 to 100,000 cps in winter grade, and Karnak sells 19 Ultra in Summer, Semi and Winter grades.
| Grade | Consistency | Where it goes |
|---|---|---|
| Brush grade | Pourable, close to a heavy coating | Broad detail areas and embedding fabric on flat surfaces |
| Butter grade | Whipped, holds a peak like frosting | Filling voids, cracks, seams, and small gaps |
| Flashing grade | Highest viscosity, non-sag | Vertical walls, curbs, and parapet base flashing |
How to apply roof mastic the right way
Applied correctly, mastic is a fabric-reinforced detail, not a smear over a wet spot. The strongest version is the three-course method (mastic, fabric, mastic) that Tremco specifies for ELS at 25 sq ft per 5-gallon pail, and the fabric is what gives the detail its tensile strength. APOC 483 polyester reinforcing fabric, for reference, comes in 4 in by 300 ft rolls.
- Clean and dry the area. Remove dirt, loose granules, rotted felts and old failed sealant; Tremco calls for a “clean, sound, dry base” and AP-2400 calls for a pressure-washed surface.
- Prime if the label requires it. Some silicone and acrylic mastics need a primer over asphalt, rust, or single-ply to bond.
- Check temperature. Apply JM MBR Utility Cement between 40°F and 100°F, keep Tremco ELS at 45°F or above, and work AP-2400 between 50°F and 90°F for best results.
- Apply the base coat. Trowel or brush a base layer wider than the damage on all sides; an asphalt cement single layer is about 1/8 inch, while AP-2400 goes on at no more than 50 wet mils per pass.
- Embed polyester reinforcing fabric. Press the fabric into the wet base so it fully saturates, with no dry spots, bridging, or wrinkles.
- Apply the top coat. Cover the fabric so no threads show through; for a silicone mastic, build to at least the 25 dry mils AP-2400 specifies.
- Feather the edges. Taper the mastic into the surrounding surface so water sheds off rather than pooling at a hard edge.
- Cure before the field coating. AP-2400 lists a 12 to 18 hour cure, and Tremco warns against applying ELS when rain is imminent before cure.
When roof mastic fails (and when not to use it)
Mastic fails most often because it was used as a cure-all instead of a detail sealant. It will not fix a roof that is saturated, ponding or structurally shot, and Tremco’s ELS data sheet calls for embedded reinforcing fabric for roof repairs and over flashing laps, so a thick unreinforced glob is the version most likely to crack. Mastic buys time and seals details; it does not replace a failed membrane.
Skip mastic or expect a short life when:
- The leak is active and the substrate is wet. ASTM D4586 Class I cements are for essentially dry surfaces; dry the detail first or use a Class II or wet-rated product.
- You are troweling it thick with no fabric. A heavy unreinforced bead shrinks and cracks as the solvent flashes off.
- You are trying to coat the whole roof with it. At 12 sq ft per gallon for an asphalt cement, a 1,000 sq ft roof would need about 83 gallons; that is a coating’s job.
- The roof has widespread ponding water. Address slope and drainage first, or the detail sits underwater and degrades.
How much does roof mastic cost?
Roof mastic is inexpensive per unit, and the real cost of a detail repair is usually labor and the reinforcing fabric, not the pail. On Google Shopping listings checked October 19, 2026, asphalt cement ran about $5 per tube and $25 to $35 per gallon, while silicone mastic ran about $71 to $95 per gallon.
| Product | Listed price | Notes | Source |
|---|---|---|---|
| Gardner Wet-R-Dri roof cement, caulk tube | $4.84 to $5.95 | Small patches, caulk gun | American Copper & Brass, Arbor, Star Mobile Home Supply listings, Oct 19, 2026 |
| Karnak 19 flashing cement, 1 gallon | $24.97 to $34.99 | Covers about 12 sq ft at 1/8 in (Tremco and JM rates for similar cements) | Home Depot, Best Materials listings, Oct 19, 2026 |
| Karnak 19 Ultra wet/dry, 5 gallon | $85.87 to $106.00 | About $17 to $21 per gallon | Builders Warehouse, Arbor listings, Oct 19, 2026 |
| Acrylic elastomeric roof patch, 1 gallon | $29.99 to $50.00 | Rust-Oleum Elastomeric Roof Patch; Davlin 810 white mastic | Maycrest Hardware, Davlin listings, Oct 19, 2026 |
| GAF Silicone Mastic, 2 gallon | $142.86 to $189.75 | About $71 to $95 per gallon | Lakefront Supply, Coatings Supply listings, Oct 19, 2026 |
| APOC 483 polyester fabric, 4 in x 300 ft | $24.88 to $41.95 | Reinforcement for 3-course details | Arbor, Roofing Direct listings, Oct 19, 2026 |
Retail listings shift with region, brand and solvent content, and VOC content is regulated in some states: the asphalt cements above list under 250 g/L, and AP-2400 silicone lists under 50 g/L. Price the reinforcing fabric into a repair, since the three-course detail is what makes mastic last.
Frequently asked questions about roof mastic
Is roof mastic the same as roofing cement?
On an asphalt or shingle roof, yes: ASTM D4586 classifies the trowel-grade asphalt paste as roof cement, and labels use both words. In the commercial coating world, mastic means a reinforced detail compound applied under a field coating, which is a distinct step. So they are the same asphalt product but a different role once you are working inside a coating system.
What is roof mastic used for?
Roof mastic seals the leak-prone details on a roof: seams, splits, pipe penetrations, vents, curbs, drains, fasteners and base flashing. It is applied about 1/8 inch thick for asphalt cement, or at least 25 dry mils for a silicone mastic such as AP-2400, and usually reinforced with polyester fabric in a three-course patch. The open field of the roof is handled by a coating or the membrane itself.
Can you apply roof mastic in the rain?
Only with a product rated for it. ASTM D4586 Class I roof cements are for essentially dry surfaces, while Class II cements, such as Karnak 19 Ultra, are made for damp, wet or underwater surfaces, and some silicone mastics like AP-2400 state wet and underwater use. Treat any wet-weather patch as temporary and redo it dry with fabric.
How long does roof mastic last?
Makers of roof cement do not publish a service life, so tie the answer to the system. A silicone mastic built into a warranted silicone coating system may be covered under that system’s warranty, while an exposed asphalt patch should be inspected every spring and fall. Fabric reinforcement and hitting the data-sheet thickness (1/8 inch for asphalt cement, 25 dry mils minimum for AP-2400) matter most.
Can roof mastic stop an active leak?
Mastic can seal an active leak at a crack, seam or penetration, but only a Class II wet-surface cement or a wet-rated silicone mastic will bond while the detail is wet. It cannot fix a saturated deck, ponding water or a failed membrane. Find the leak source, dry it if you can, then seal it with mastic, polyester fabric and a second mastic coat.
What is the difference between mastic and sealant?
Mastic is a thick, often fabric-reinforced paste, laid about 1/8 inch thick in asphalt form, for broad details such as seams, curbs and flashing. A sealant is a thinner, standalone caulk for joints under 1 inch, gaps and fastener heads. Use sealant for a tight joint you can run a bead into, and mastic for a broad detail you need to reinforce.