Spray polyurethane foam roofing (SPF) is a fluid-applied roof system that arrives as two liquids, reacts on contact, expands into a rigid closed-cell foam of about 2.5 to 3.0 lb per cubic foot, and cures into a jointless waterproof layer bonded to the deck. It is used mainly on flat and low-slope commercial, industrial, and some residential roofs, where the foam supplies both waterproofing and roughly R-6.5 per inch of insulation in one pass and is then protected by an elastomeric topcoat, often with roofing granules broadcast into the last coat.
By The Roofing Brief Team. Last reviewed: October 2026.
What is spray polyurethane foam roofing?
Spray polyurethane foam roofing is a monolithic roof system made by spraying two liquid chemicals, an isocyanate (the A side) and a polyol resin blend (the B side), through a heated plural-component gun at a 1:1 ratio by volume. On the General Coatings Ultra-Thane 230 HFO Roofing data sheet, cream time is 1 to 2 seconds and rise time 4 to 7 seconds, depending on the winter, regular or summer reactivity grade. Because it is sprayed as one continuous membrane with no seams or fasteners, the usual leak paths at laps are removed.
The foam alone is not the finished roof. Ultraviolet light causes dusting and discoloration of bare foam, per the PROFOAM PF-ROOF data sheet, and General Coatings says Ultra-Thane 230 performs best when coated the same day and may be left exposed for up to 24 hours. Every SPF roof therefore gets an elastomeric coating, most often silicone, acrylic or urethane, that carries the UV, weather and foot-traffic load.
SPF is applied over existing built-up, modified bitumen, metal, single-ply (with a cover board) and concrete substrates. The American WeatherStar SPF guide dates roofing use to the late 1970s and recommends an infrared moisture survey before foam goes over an old roof, because a saturated substrate is the main reason an SPF recover gets rejected.
SPF roofing specs: density, R-value, cost, and lifespan
Roofing-grade spray polyurethane foam is closed-cell foam sprayed at about 2.5 to 3.0 lb per cubic foot, insulating at about R-6.3 to R-6.5 per inch on maker data sheets, installed for about $3.50 to $8 per square foot across two published ranges, and expected to last 40 or more years with regular care per the Spray Polyurethane Foam Alliance (SPFA). Each figure traces to a test method, standard or named source below.
| Property | Typical roofing spec | Governing standard or source |
|---|---|---|
| Material standard | Type III or IV foam | ASTM C1029, as required by IBC 1507.14.2; roofing-specific spec ASTM D7425 |
| Density (closed-cell roofing foam) | 2.5, 2.7 or 3.0 lb/ft³ grades | ASTM D1622; Ultra-Thane 230 HFO data sheet |
| Compressive strength | 40 to 60 psi (rises with density) | ASTM D1621; Ultra-Thane 230 HFO data sheet |
| R-value (aged) | R-6.3 to R-6.5 per inch | ASTM C518; Gaco, General Coatings and Polyglass data sheets |
| Applied foam thickness | 1 in minimum, built up to drain | Gaco SPF-S42-26-15 specification; American WeatherStar guideline |
| Minimum design slope | 1/4 in per foot (2 percent) | IBC 1507.14.1 |
| Closed-cell content | 93 to 98 percent | PROFOAM PF-ROOF; Gaco F2733RHFO (ASTM D2856) |
| Installed cost | $3.50 to $7.00 per sq ft (HomeGuide); $5 to $8 (American WeatherStar) | HomeGuide, April 2023; American WeatherStar SPF guide |
| Coating thickness | 20 to 40 mils dry, set by warranty term | American WeatherStar Foam-Gard application guideline |
| Service life | 40 or more years with regular care | SPFA |
| Recoat interval | Every 10 to 15 years | American WeatherStar SPF guide |
The density number is the one that separates a roofing foam from an insulation foam. On the Ultra-Thane 230 data sheet, compressive strength climbs from 40 to 45 psi at 2.5 lb density to 50 to 60 psi at 3.0 lb, and American WeatherStar says 2.7 to 3.0 lb foam is what is rigid enough to walk on. If you are comparing SPF against other assemblies, our breakdown of spray foam versus a single-ply roof lines up the cost and lifespan side by side.
Roofing foam by maker: published data sheet values
| Product | Density (lb/ft³) | Compressive strength | Aged R-value | Closed cell | Fire rating noted | Source |
|---|---|---|---|---|---|---|
| Gaco GacoRoofFoam F2733RHFO | 2.7 to 3.4 | 53.7 psi | R-6.5 at 1 in; R-25 at 3.5 in | 98.2% | ASTM E108 Class A; exceeds ASTM C1029 Type III | Gaco PDS, rev. 12/2024 |
| General Coatings Ultra-Thane 230 HFO Roofing | 2.5 / 2.7 / 3.0 | 40 to 45 / 46 / 50 to 60 psi | R-6.47 per in | 95% / 95% / 98% | ASTM E108 Class A or B; FM 4470 uplift over I-450 | Ultra-Thane 230 HFO TDS |
| Polyglass PolyPUF 2.5 | 2.4 to 2.6 | 45 psi | R-6.3 per in (calculated) | Not listed on PDS | UL 790 Class A on non-combustible decks; Class B at 1 in minimum on combustible decks | Polyglass PolyPUF 2.5 PDS |
| PROFOAM PF-ROOF | 2.8 | 54 psi | R-6.3 at 1 in; R-9.8 at 1.5 in; R-13.4 at 2 in | Over 93% | ASTM E84 flame spread under 75 | PROFOAM data sheet |
Read this table as published laboratory values, not field results: every maker above notes that applied properties depend on equipment, temperature and the applicator. The Gaco and General Coatings products use HFO blowing agents; PF-ROOF is an older HFC-245fa formula.
Open-cell vs closed-cell foam: which one goes on a roof
Only closed-cell foam belongs on a roof. Closed-cell SPF sprays at about 2.5 to 3.0 lb/ft³, resists water, and is rigid enough to walk on and shed rain, which is what a roof surface has to do. Open-cell foam sprays at roughly 0.5 lb/ft³, stays soft, and absorbs water, so it is used for interior insulation and sound control, not as a weather surface.
| Attribute | Closed-cell (roofing) | Open-cell (interior insulation) |
|---|---|---|
| Density | About 2.5 to 3.0 lb/ft³ | About 0.4 to 0.6 lb/ft³ |
| R-value per inch | About R-6 to R-6.5 | About R-3.5 to R-3.8 |
| Water behavior | Resists water, sheds it | Absorbs water |
| Where it is used | Roof surfaces, exterior | Attics, walls, interior |
This is the line that keeps roofing SPF separate from the attic product. PROFOAM labels PF-ROOF an exterior roof membrane not designed for interior use, and says foam sprayed inside a building needs a thermal barrier such as 1/2 in gypsum board or 1/2 in cement plaster per the applicable code. If your question is about insulating the space under the roof rather than surfacing it, that decision runs on the interior insulation side of the house.
SPF roofing granules: broadcast rates, fire rating and walkways
Spray polyurethane foam roofing granules are mineral roofing granules broadcast into the wet finish coat, and the common maker rate is 30 lb per 100 sq ft. That rate appears in the Gaco SPF-S42-26-15 specification, the American WeatherStar Foam-Gard guideline and the Polyglass PolyPUF fire listings. Granules add traction, abrasion and some impact resistance, and on several listed assemblies they are part of the fire rating, so they are not purely cosmetic.
| Granule use | Published rate or rule | Source |
|---|---|---|
| Full-field granules over GacoFlex S42 silicone on SPF | 30 lb per 100 sq ft, broadcast immediately into the finish coat | Gaco SPF-S42-26-15 |
| Foam-Gard over single-ply (acrylic or silicone) | 30 lb per 100 sq ft, optional on 10, 15 and 20 year systems | American WeatherStar guideline |
| Fire-listed PolyPUF 2.5 assemblies | 30 lb per 100 sq ft, depending on configuration, for UL 790 Class A (non-combustible) and Class B (combustible) listings | Polyglass PolyPUF 2.5 PDS |
| Walk pads (GacoFlex SF2036 WalkPad) | 4 gal per 100 sq ft for 64 mils wet, then safety-yellow granules at 0.5 lb per 100 sq ft | Gaco SPF-S42-26-15 |
The decision rule: if the roof carries regular service traffic (HVAC units, solar arrays) or the fire listing you are relying on names granules, specify them. If the roof is a low-traffic residential deck with no listing requirement, granules are optional, and a granulated surface takes more coating at recoat time: Gaco’s S42 data sheet sets 1.75 gallons per 100 sq ft for granulated and other rough surfaces.
How much does spray polyurethane foam roofing cost?
A spray polyurethane foam roof costs $3.50 to $7.00 per square foot installed on average, or $6,500 to $11,600 for a typical project, per HomeGuide’s SPF cost guide (April 2023). American WeatherStar quotes $5 to $8 per square foot for commercial SPF, with foam thickness and roof size and complexity as the main drivers. HomeGuide puts a polyurea recoat at $1.50 to $4.00 per square foot.
| Roof area | Installed at $3.50 to $7.00 per sq ft | Source |
|---|---|---|
| 1,000 sq ft | $3,500 to $7,000 | HomeGuide, April 2023 |
| 2,000 sq ft | $7,000 to $14,000 | HomeGuide, April 2023 |
| 3,000 sq ft | $10,500 to $21,000 | HomeGuide, April 2023 |
Recoating is a planned cost, not a failure. Coating quantity drives it: Gaco’s SPF spec calls for 1.75 gal per 100 sq ft of S42 silicone to reach 26 mils dry, and American WeatherStar steps silicone from 20 mils (10 year system) to 40 mils (20 year system). Our detailed foam roof cost report breaks down recoat cycles and lifetime spend, and whether foam roofing fits a house covers the residential side.
Coating thickness by warranty term
| System warranty term | Acrylic system | Silicone system | Source |
|---|---|---|---|
| 10 year | 30 mil | 20 mil | American WeatherStar Foam-Gard guideline |
| 15 year | 35 mil | 30 mil | American WeatherStar Foam-Gard guideline |
| 20 year | 38 mil | 40 mil | American WeatherStar Foam-Gard guideline |
Other manufacturers publish their own tiers (Gaco’s S42 SPF spec, for example, targets 26 mils dry), so ask the bidder which manufacturer’s mil table the quote is built on and get the dry film thickness written into the contract.
How a spray foam roof is installed
A spray foam roof is installed in a fixed sequence: prep and dry the deck, spray the foam to thickness and slope, then coat it the same day. Per the SPFA, applicators are trained on the spray equipment, the foam and coating materials, and roofing practice, and the SPFA runs a roofing contractor certification. The numbers in each step below come from the named data sheets.
- Inspect and prep the deck. Remove debris, dirt and oils, and cut out wet or saturated areas, because moisture trapped under foam becomes blisters. General Coatings says wood and concrete need moisture content under 10 percent to skip priming.
- Dry the surface and prime if needed. Gaco’s F2733RHFO data sheet sets a 45 °F minimum substrate temperature and bars spraying within 5 °F of the dew point; General Coatings calls for priming bare ferrous metal and wash-priming galvanized steel.
- Set the equipment. General Coatings specifies heated equipment holding 120 to 140 °F mixed material at the gun; Gaco caps the setting at 130 °F and runs the resin side 10 to 15 °F warmer than the isocyanate.
- Spray the foam to thickness. Apply passes of 1/2 to 1 1/2 in (Ultra-Thane 230) or 0.75 to 1.5 in (Gaco) to reach at least 1 in total, building slope to a design minimum of 1/4 in per foot under IBC 1507.14.1.
- Check the cured foam. American WeatherStar’s guideline requires the full foam thickness in any area to be finished before the end of each day, and allows +1/4 in per inch of thickness over spec but nothing under. A smooth or orange-peel surface is the target; a popcorn texture takes far more coating.
- Apply the base coat of elastomeric coating. Spray the first silicone, acrylic or urethane coat over clean, cured foam, at the rate the coating maker sets for the warranty tier; the American WeatherStar 10 year silicone system totals 20 mils dry across all coats.
- Apply the top coat and granules. Add the finish coat to the specified dry film thickness (for example 26 mils of GacoFlex S42), then broadcast granules at 30 lb per 100 sq ft into the wet coat if specified.
Timing matters between steps. General Coatings allows Ultra-Thane 230 to sit uncoated for up to 24 hours before it asks the contractor to call for recommendations. When a coating wears through or the foam is punctured, spot repair is straightforward; our guide to foam roof repair walks through fixing blisters, holes and worn coating.
Which ASTM standards apply to SPF roofing?
Spray polyurethane foam roofing is governed by building code sections plus ASTM standards that define the foam grade, how its properties are measured, and how the assembly resists fire. The International Building Code section for SPF roofs is 1507.14, quoted here from the Massachusetts adoption, 780 CMR 1507.14.
- IBC 1507.14.1 requires a design slope of at least one-fourth unit vertical in 12 units horizontal (2 percent) for drainage.
- IBC 1507.14.2 requires the foam to be Type III or IV as defined in ASTM C1029.
- ASTM C1029 is the specification for spray-applied rigid cellular polyurethane thermal insulation and sorts foam into Types I to IV. Gaco states F2733RHFO exceeds Type III.
- ASTM D7425 is the specification for spray polyurethane foam used for roofing applications; per its scope it covers types and physical properties, not application.
- ASTM D1622 measures apparent density, the source of the 2.5 to 3.0 lb/ft³ figures.
- ASTM D1621 measures compressive strength, the property that lets a roof foam carry foot traffic.
- ASTM C518 measures thermal resistance, the source of the R-6.3 to R-6.5 per inch values.
- ASTM D6083 is the specification for liquid-applied acrylic coating used over SPF, covering tensile strength, elongation and weathering.
- ASTM E108 (UL 790) is the external fire test for roof coverings that assigns a Class A, B or C rating to the assembly.
Installer competence is standardized too. The SPFA runs a roofing contractor certification and accreditation program, and specifiers often require SPFA-certified crews. Which fire class and thickness a project needs depends on the code edition your jurisdiction adopted and on the listed assembly, so ask the bidder for the UL or FM listing number of the exact foam, coating and granule combination.
Pros and cons of spray foam roofing
Spray foam roofing trades a demanding installation for a jointless, insulating, renewable roof. Its strengths are no seams, about R-6.5 per inch, and the option to recoat every 10 to 15 years instead of tearing off. Its weaknesses are a weather-limited install window (Gaco’s 45 °F substrate floor, General Coatings’ 50 °F minimum in most instances) and dependence on the applicator. The tradeoffs line up like this.
| Strengths | Limitations |
|---|---|
| No seams or fasteners, which removes the most common leak paths | Cannot be sprayed in rain, high wind, or on a wet deck, which limits install days |
| High insulation value at about R-6 to R-6.5 per inch | Overspray can drift onto cars and neighboring property in wind if not masked |
| Renewable by recoating instead of full tear-off | Quality depends heavily on applicator skill and equipment calibration |
| Lightweight, so it can often recover an existing roof | Coating needs recoating every 10 to 15 years to keep protecting the foam, per American WeatherStar |
| Self-flashing around penetrations and curbs | Bare foam must be coated quickly; General Coatings allows up to 24 hours uncoated |
Maintenance, recoating, and lifespan
The SPFA says a spray foam roof with regular care is expected to last 40 or more years, and calls for inspections twice a year and after severe weather. The foam is stable once protected; what ages is the coating, which American WeatherStar says needs recoating every 10 to 15 years. The SPFA’s full procedure is in its SPFA-127 Maintenance Manual for Spray Polyurethane Foam Roof Systems.
Routine maintenance is light: clear debris, check the coating around HVAC curbs, drains and walk paths, and seal punctures before water reaches the foam. Per American WeatherStar, minor damage can usually be repaired with roofing-grade mastic or sealant, which is the economic argument for SPF on large low-slope buildings.
When spray polyurethane foam roofing is (and isn’t) the right call
Spray polyurethane foam roofing fits flat and low-slope roofs where insulation, a lightweight recover and no seams are worth a weather-dependent install. American WeatherStar puts a typical 20,000 sq ft commercial install at about 2 weeks, weather permitting. It is a weaker fit where install-day weather stays under 50 °F, where no SPFA-certified applicator works locally, or on steep-slope roofs, where fewer foam makers list their product; General Coatings is one that lists low slope, pitched and barrel roofs for Ultra-Thane 230.
| If your roof is… | Then | Threshold or rule | Source |
|---|---|---|---|
| Flat with ponding water | SPF can build slope as it goes | Design slope at least 1/4 in per foot | IBC 1507.14.1 |
| An old built-up or single-ply roof you want to recover | Survey for moisture first | Remove wet areas; infrared survey recommended | American WeatherStar SPF guide |
| A wood or concrete deck | Prime unless dry | Under 10% moisture content to skip primer | Ultra-Thane 230 HFO TDS |
| Walked on often (HVAC, solar) | Use 2.7 to 3.0 lb foam plus granules and walk pads | Granules 30 lb per 100 sq ft | American WeatherStar; Gaco SPF-S42-26-15 |
| On a combustible (wood) deck | Check the fire listing | PolyPUF 2.5: Class B at 1 in minimum with granules | Polyglass PolyPUF 2.5 PDS |
| In a climate with long cold seasons | Schedule for warm, dry days | Substrate at least 45 to 50 °F and 5 °F above dew point | Gaco F2733RHFO; Ultra-Thane 230 TDS |
| Steep-slope rather than low-slope | Use only a foam the maker lists for pitched roofs | Ultra-Thane 230 is listed for low slope, pitched and barrel roofs | General Coatings roof foam page |
For a homeowner weighing it against other low-slope options, compare bids on three written numbers: foam thickness in inches, coating dry film thickness in mils, and the warranty term those mils buy. Our pages on residential foam roofing and the full foam roof cost picture cover those tradeoffs in more depth. Treat contractor bids and manufacturer specs as the governing numbers for a specific project.
Frequently asked questions
What is spray polyurethane foam roofing?
Spray polyurethane foam roofing (SPF) is a roof system sprayed on as two liquid chemicals that react, expand and cure into rigid closed-cell foam of about 2.5 to 3.0 lb per cubic foot bonded to the deck. The foam waterproofs and insulates in one layer with no seams, then gets a silicone, acrylic or urethane coating for UV and weather protection. It is used mainly on flat and low-slope roofs.
How long does a spray foam roof last?
The Spray Polyurethane Foam Alliance says a spray foam roof with regular care is expected to last 40 or more years. The foam is stable once protected, but the coating that shields it from UV wears, and American WeatherStar says it needs recoating every 10 to 15 years. With that maintenance, the same foam base can stay in service for decades without a full replacement.
What is the R-value of spray foam roofing?
Closed-cell roofing foam is rated about R-6.3 to R-6.5 per inch aged, measured per ASTM C518. Gaco lists R-6.5 at 1 inch and R-25 at 3.5 inches for GacoRoofFoam F2733RHFO, and PROFOAM lists R-9.8 at 1.5 inches and R-13.4 at 2 inches for PF-ROOF. That R-value per inch is a main reason SPF is chosen for low-slope buildings.
How much does spray foam roofing cost per square foot?
HomeGuide puts spray foam roofing at $3.50 to $7.00 per square foot installed, or $6,500 to $11,600 for a typical project (April 2023). American WeatherStar quotes $5 to $8 per square foot for commercial SPF, driven mainly by foam thickness and roof size and complexity. HomeGuide puts a polyurea recoat at $1.50 to $4.00 per square foot.
Are granules required on a spray foam roof?
Not always. Granules are optional on many coating systems, but some fire-listed assemblies include them, such as Polyglass PolyPUF 2.5 listings that call for granules at 30 lb per 100 sq ft. Gaco and American WeatherStar specs use the same 30 lb per 100 sq ft broadcast rate into the wet finish coat. Specify them where the roof gets foot traffic or the listing requires them.
Is spray foam roofing the same as attic spray foam insulation?
No. Roofing SPF is a rigid closed-cell foam at about 2.5 to 3.0 lb per cubic foot sprayed on the roof surface and coated to resist weather. Attic and wall spray foam is usually a lighter, softer product, including open-cell foam near 0.5 lb per cubic foot, used to insulate the space under the roof. They are different grades for different jobs, and only closed-cell roofing foam belongs on a roof surface.
Can spray foam be applied over an existing roof?
In many cases yes. SPF bonds to built-up, modified bitumen, metal and concrete, and to single-ply with a cover board, so it is often used to recover an existing low-slope roof instead of tearing it off. The existing surface must be dry and sound, wet areas must be removed first, and American WeatherStar recommends an infrared moisture survey. Local code may limit recover layers.
What maintenance does a spray foam roof need?
The Spray Polyurethane Foam Alliance calls for inspections twice a year and after severe weather. Clear debris, check the coating around curbs, drains and walk paths, and seal coating breaks or punctures before water reaches the foam. The main scheduled task is recoating, which American WeatherStar puts at every 10 to 15 years. The SPFA-127 Maintenance Manual covers the full procedure.