Subscribe

MATERIALS · July 17, 2026

Greenhouse Roof Panels: Materials, Light %, and Cost (2026)

Compare greenhouse roof panels: glass, twin-wall and multiwall polycarbonate, acrylic, and film on light, R-value, cost, and lifespan. Pick the right one.

The best greenhouse roof for most home and community greenhouses is twin-wall polycarbonate, because it holds roughly double the insulation of glass (R-1.7 against R-0.9) at about $2 to $3 per sq ft against $4 to $6. Greenhouse roof panels come down to five materials: glass, twin-wall polycarbonate, multiwall polycarbonate, acrylic and polyethylene film. Glass suits high-end, high-light builds and film suits large commercial hoop houses on a budget. Light transmission is measured by ASTM D1003, and polycarbonate sheet makers such as Palram publish thickness, R-value and warranty data.

Reviewed by The Roofing Brief Team. Last reviewed: October 2026.

Which greenhouse roof panel material is best?

Glass gives the highest clarity (90 to 92%), polycarbonate the best insulation per dollar, and polyethylene film the lowest upfront price ($0.10 to $0.50 per sq ft). The ranges below are typical published figures; the maker’s data sheet for the exact panel controls.

Panel material Light transmission R-value (insulation) Cost per sq ft Lifespan
Single-pane glass 90 to 92% ~0.9 $4 to $6 25+ years
Twin-wall polycarbonate (8mm) ~80% ~1.7 $2 to $3 10 to 15 years
Multiwall polycarbonate (16mm) ~65% ~2.5 $3 to $5 10 to 15 years
Acrylic (plexiglass) ~90% ~0.9 to 1.0 $3 to $7 15 to 20 years
Polyethylene film (6 mil) 85 to 90% ~0.8 (single layer) $0.10 to $0.50 3 to 5 years

Polycarbonate makers commonly quote about 250 times the impact strength of glass at roughly half the weight (a maker claim, not an independent test), which is why it is used in hail-prone regions and DIY builds. Glass keeps its clarity for decades but cracks on impact and loads the frame. Film needs replacing every 3 to 5 years.

Light transmission vs light diffusion: what your plants actually need

Glass and film pass 85 to 92% of light as direct beams, while twin-wall and multiwall polycarbonate pass about 65 to 80% but scatter it, which reaches lower leaves and cuts hot spots and leaf scorch.

Match the panel to your crop’s daily light integral (DLI), the total usable light a plant receives per day:

  • High-light crops (tomatoes, peppers, cannabis) want maximum transmission: glass, acrylic, or single-wall polycarbonate.
  • Leafy greens, herbs, and seedlings tolerate and often prefer diffused light: twin-wall polycarbonate is ideal.
  • Shade-sensitive starts and propagation benefit from the even light of multiwall panels, which prevent the scorch that direct beams cause under glass.

In cloudy northern climates choose the higher-transmission end (80% twin-wall or glass); in bright southern climates, diffused polycarbonate limits summer scorch.

Polycarbonate thickness: which mm for your climate

Thicker multiwall panels trap more air layers, raising R-value from about 1.4 at 4mm to about 2.5 at 16mm but cutting transmission from about 82% to about 65%. Match thickness to your zone on the USDA Plant Hardiness Zone Map.

Thickness Structure Approx. R-value Light transmission Best for
4mm to 6mm Twin-wall 1.4 to 1.6 ~82% Mild climates, USDA zones 8 to 10, season extension
8mm Twin-wall ~1.7 ~80% Most home greenhouses, zones 5 to 8
10mm Twin or triple-wall ~2.0 ~78% Cold nights, shoulder-season heating, zones 4 to 6
16mm Multiwall (5-wall) ~2.5 ~65% Year-round growing in cold climates, zones 3 to 5

An 8mm twin-wall panel (R-1.7, about 80% light) is the default for zones 5 to 8 because it insulates about twice as well as single-pane glass (R-0.9). Step up to 16mm (R-2.5, about 65% light) only if you heat through zone 3 to 5 winters; the 15-point transmission drop can mean grow lights for tomatoes and peppers.

How long greenhouse roof panels last and the true lifetime cost

Polyethylene film looks cheapest at $0.10 to $0.50 per square foot, but UV-stabilized film needs full replacement every 3 to 5 years, so over a 15-year span you buy it three to four times. Twin-wall polycarbonate lasts 10 to 15 years before its UV coating degrades and the panels yellow or grow brittle. Glass can exceed 25 years if the frame stays sound.

Run the math over 15 years for a 200 square foot roof:

  • Polyethylene film: about $0.30/sq ft, replaced 4 times, roughly $240 in material plus repeated labor.
  • Twin-wall polycarbonate (8mm): about $2.50/sq ft, replaced once at most, roughly $500 to $1,000 total.
  • Glass: about $5/sq ft installed once, roughly $1,000 with no replacement in the window.

Film wins on cash but costs the most labor and downtime. Polycarbonate is the value midpoint. Glass costs the most upfront and the least over decades if it never takes an impact. UV degradation is the clock on plastics: a panel sold with a 10-year UV warranty is telling you when to budget the next roof.

Installation details that decide whether panels leak or fog

Multiwall polycarbonate yellows and cracks years early if installed with the UV side inward. These four steps prevent the common failures.

  1. Face the UV side out. The protective film or printed label marks the sun side. Peel it only after the panel is set, and never flip the sheet.
  2. Seal the flutes. Multiwall channels must be closed with breathable anti-dust tape on top and vented tape on the bottom so condensation drains instead of pooling and growing algae inside the walls.
  3. Run flutes vertically. Orient the internal channels down the slope so water and condensate drain out the low edge rather than sitting in the panel.
  4. Leave room for thermal movement. Polycarbonate expands and contracts with temperature swings. Oversize screw holes slightly and use gasketed screws so panels can move without cracking or lifting.

An anti-drip coating on the interior face makes condensation sheet down the panel instead of dripping onto plants. The same drainage and thermal-movement rules apply to other clear roof panels.

How to choose your greenhouse roof panels

If your greenhouse… Then choose
is in USDA zones 3 to 5 and heated through winter 10mm or 16mm multiwall polycarbonate (R-2.0 to 2.5)
is a typical home greenhouse in zones 5 to 8 8mm twin-wall polycarbonate (R-1.7, about 80% light)
is in zones 8 to 10 for season extension 4mm to 6mm twin-wall or film
grows high-light fruiting crops Glass or acrylic (about 90% light)
is a large hoop house on a tight cash budget 6 mil polyethylene film at $0.10 to $0.50 per sq ft, replaced every 3 to 5 years
faces hail or falling limbs Polycarbonate rather than glass

Then work through these steps in order.

  1. Start with your winter low. Zones 3 to 5 call for 10mm or 16mm multiwall (R-2.0 to 2.5); zones 8 to 10 can run 6mm twin-wall (R-1.6) or film.
  2. Layer in your crops. High-light fruiting plants push you toward glass or thinner, brighter panels. Greens and starts allow thicker, diffused polycarbonate.
  3. Set the lifespan you want. Buy-once thinking favors polycarbonate or glass. Lowest-cash-now thinking favors film with a replacement budget.
  4. Confirm impact risk. Hail, falling limbs, or kids and pets nearby argue for polycarbonate over glass every time.

Related glazing: plastic roofing sheets and corrugated roof panels, and see how greenhouse glazing sits within the broader types of roofing materials.

Frequently asked questions

What is the best material for a greenhouse roof?

Twin-wall polycarbonate is the best material for most greenhouse roofs because it insulates about twice as well as glass, resists impact roughly 250 times better, and costs $2 to $3 per square foot. Glass is better for high-light crops and premium builds, while polyethylene film is better for large, budget commercial hoop houses that accept replacement every few years.

Is polycarbonate or glass better for a greenhouse?

Polycarbonate is better for insulation, impact resistance, and cost, while glass is better for light clarity and lifespan. Twin-wall polycarbonate holds roughly double the R-value of glass and shrugs off hail, but glass passes 90 to 92% of light versus about 80% for polycarbonate and can last 25 years or more. Cold climates and DIY builds favor polycarbonate; high-light crops and high-end greenhouses favor glass.

What thickness of polycarbonate is best for a greenhouse roof?

8mm twin-wall polycarbonate is best for most home greenhouses, giving an R-value near 1.7 and about 80% light transmission. Choose 4mm to 6mm in mild climates for season extension, and step up to 16mm multiwall (R-value near 2.5) for year-round growing in USDA zones 3 to 5, accepting lower light transmission around 65%.

How long do polycarbonate greenhouse panels last?

Polycarbonate greenhouse panels last 10 to 15 years before UV degradation causes yellowing and brittleness. The UV-protective coating is the limiting factor, so a panel sold with a 10-year UV warranty signals when to budget replacement. Facing the UV-treated side toward the sun and sealing the flutes correctly helps panels reach the top of that range.

Which side of a polycarbonate greenhouse panel faces up?

The UV-protected side of a polycarbonate panel must face up toward the sun, marked by a printed protective film or label. Installing it upside down leaves the untreated side exposed, causing the panel to yellow, cloud, and crack years earlier than rated. Peel the marking film only after the panel is fastened in place.

How much do greenhouse roof panels cost?

Greenhouse roof panels cost about $0.10 to $0.50 per square foot for polyethylene film, $2 to $3 for 8mm twin-wall polycarbonate, $3 to $5 for 16mm multiwall, and $4 to $6 for tempered glass. Film is cheapest upfront but needs replacing every 3 to 5 years, so polycarbonate often costs less over a 15-year span.