Subscribe

MATERIALS · July 17, 2026

Clear Roof Panels: Materials, Light %, and Cost (2026)

Clear roof panels compared: 90% light for clear vs 35% for bronze polycarbonate, $1 to $4.89 per sq ft at Menards, slope and purlin rules from Palram.

By The Roofing Brief Team. Last reviewed: October 2026.

Clear roof panels are translucent roofing sheets, usually polycarbonate, PVC, acrylic or fiberglass, that let daylight through while shedding rain over patio covers, carports, porches, pergolas and greenhouses. Three specs decide whether a panel works: light transmission (Palram rates its clear Suntuf polycarbonate at 90% and its Bronze at 35%), a UV-protected face, and a minimum slope of 1 1/2 inches per 12 inches for corrugated polycarbonate, per the Suntuf installation guide. Retail prices at Menards in October 2026 ran from about $1.00 per square foot of coverage for clear PVC to about $4.89 for 8 mm twinwall polycarbonate.

What are clear roof panels?

Clear roof panels are see-through or translucent sheets that form a weatherproof roof while transmitting daylight. Most are plastic: corrugated or multiwall polycarbonate, corrugated PVC, cast acrylic or corrugated fiberglass. “Clear” means the highest light transmission, about 90% on Palram Suntuf Clear; “opal,” “white,” “smoke,” “solar gray” and “bronze” are tinted versions of the same sheet that trade brightness for less glare and heat, down to 35% for Suntuf Bronze and Solar Grey.

These panels fasten to purlins or a rafter frame, not to a solid deck, so the light reaches the space below. Palram’s guide sets purlins no more than 36 inches apart and recommends 24 inches, which is why clear panels show up over patios, decks and greenhouses rather than over heated living space. Over a room, a clear panel roof competes with a run of skylights on cost and comfort.

Clear roof panel materials compared

The four common clear roofing materials split on light (20% to 90% by color), strength and warranty (5 years to limited lifetime). Polycarbonate leads on impact resistance (Amerilux markets its clear polycarbonate as 200 times stronger than glass and 10 times stronger than acrylic), PVC is the budget corrugated sheet, acrylic gives glass-like clarity but is more brittle, and fiberglass is the older utility option that dulls as its surface resin weathers. The table uses maker and retailer figures where they exist.

Material Light transmission (clear) Example retail price, Oct 2026 Warranty / service temp Impact resistance Best for
Corrugated polycarbonate 90% (Palram Suntuf Clear; Amerilux CoverLite) MR 9 clear 38 in x 8 ft panel $85.63 at Menards, about $3.57 per sq ft of coverage Suntuf: limited lifetime on light loss, 10 years on hail; -40°F to 212°F Highest of the group Patios, carports, pergolas, metal-roof skylight strips
Multiwall (twinwall) polycarbonate 82% (8 mm clear twinwall, Menards listing) 4 ft x 8 ft 8 mm sheet $156.62 at Menards, about $4.89 per sq ft 10 year (Menards listing) High Greenhouses, insulated covers
Corrugated PVC (vinyl) 90% claimed (PVCLite clear, Menards listing) PVCLite 26 in x 8 ft panel $16.00 at Menards, about $1.00 per sq ft of coverage PVCLite and Palruf: 5 year limited; Palruf -4°F to 120°F Lowest in Palram’s Good/Better/Best chart Budget patio and shed covers
Cast acrylic Check the maker sheet Not priced here Varies by maker About one tenth of polycarbonate per Amerilux Skylight domes, display glazing
Corrugated fiberglass Drops as the surface resin weathers Not priced here Varies by maker Moderate, embrittles with age Barns, utility buildings

Prices above are single panels at Menards (PVCLite clear PVC, $16.00), Menards (MR 9 clear polycarbonate, $85.63) and Menards (8 mm twinwall, $156.62), checked October 20, 2026; per square foot figures divide by net coverage (24 inches of a 26 inch corrugated panel, 36 inches of a 38 inch panel). Add fasteners, closure strips and lumber. For a fuller breakdown of the plastic sheet options, see our guide to polycarbonate vs PVC plastic roofing sheets. Cast acrylic is also a common skylight dome material; for how it compares with polycarbonate overhead, see our guide to plastic skylights.

Which clear roof panel is best for your project?

Match the panel to the load and the use, not to the lowest sticker. Palram’s load table for Suntuf ties purlin spacing to the design load: 36 inches for 20 psf, 30 inches for 30 psf, 24 inches for 40 psf and 16 inches for 50 psf. Check your local snow load first, then pick the material from the table.

If your project is Choose Threshold or spec to check
Patio cover or carport in hail country Corrugated polycarbonate (Suntuf class) 10 year hail warranty; purlins at 24 in or closer
Snow load of 40 to 50 psf Corrugated polycarbonate on tight purlins 24 in purlins at 40 psf, 16 in at 50 psf (Palram table)
Greenhouse 8 mm twinwall polycarbonate 82% light, insulating air gap, tape the flute ends
West-facing patio people sit under Bronze, Solar Grey or Opal polycarbonate 35% to 45% light instead of 90%
Shed or utility roof on a tight budget, no snow Corrugated PVC About $1.00 per sq ft; rated only to 120°F in Palruf’s chart
Roof slope under 1 1/2 in per 12 in Raise the slope or add sealant at laps Below Palram’s recommended minimum
Daylight over heated living space Skylights or a glazed roof, not panels Panels are single-wall or twinwall, not insulated glass
  • Patio cover or carport: corrugated polycarbonate. Suntuf carries a 10 year warranty against hail damage, which no PVC sheet in Palram’s line matches. Choose Opal (45%) or Solar Grey (35%) if the space faces afternoon sun.
  • Greenhouse: multiwall polycarbonate. An 8 mm clear twinwall sheet passes 82% of light per its Menards listing, diffuses it across the benches and adds an insulating air gap that holds heat overnight better than single-wall clear.
  • Porch or pergola: corrugated polycarbonate in Opal or Bronze. Rain cover and soft light at 35% to 45% transmission beat 90% clear over seating.
  • Shed or utility building: corrugated PVC or fiberglass. At $16.00 for a 26 inch by 8 foot PVCLite panel at Menards, PVC is the value pick where hail and snow loads are low.
  • Under-deck ceiling: corrugated polycarbonate at no less than 1 1/2 inches of fall per 12 inches, sealed at the laps, to keep the patio below the deck dry.

If your real goal is daylight over living space rather than an outdoor cover, price the panels against a run of skylights first. Our skylight installation cost guide shows where fixed and tubular skylights beat a panel roof on comfort and leak risk. For a permanent glazed sunroom or atrium roof, see our guide to the glass roof.

Bronze vs clear vs opal polycarbonate panels

Clear and tinted polycarbonate are the same sheet with different light transmission. Palram’s Suntuf brochure lists the values below, and every color carries the same UV-protected face and lifetime limited warranty against losing more than 10% of its light transmission (tested to ASTM D1003).

Suntuf color Light transmission Use it when
Clear 90% Greenhouse, north-facing cover, maximum daylight
Sea Green 80% Bright cover with a green cast
Sky Blue 55% Moderate shade, cool cast
White Opal 45% Even, glare-free light over a patio
Solar Grey 35% South or west exposure, cuts glare
Bronze 35% South or west exposure, warm cast
Smooth Cream 30% Shade-first patio cover
Misty Green / Solar Control Silver 20% Maximum shade
Hunter Green / Red Brick Minimal Opaque look, little daylight

Bronze vs clear is a 90% versus 35% light decision: bronze passes well under half the light of clear, so it suits a west-facing patio that takes the afternoon sun, while clear suits plants. Clear vs opaque panels follow the same scale; Palram rates Hunter Green and Red Brick as “minimal” transmission, so pick those only when you want shade and color matched to the house.

Corrugated vs multiwall vs solid clear panels

Clear panels come in three structures, and the structure drives both strength and how the panel handles heat. Corrugated is the single-layer wavy sheet (0.032 inch thick for Suntuf and PVCLite), multiwall is a hollow ribbed sheet sold by thickness in millimeters, and solid is a flat single layer like glass.

Structure Description Insulation Example thickness Typical use
Corrugated (single-wall) Wavy single sheet, laps over purlins None 0.032 in (Suntuf, PVCLite); 0.033 in (Amerilux CoverLite) Patios, carports, sheds
Multiwall Twin or triple wall with hollow ribs Yes, air gap 8 mm twinwall (0.315 in); 16 mm triple wall Greenhouses, sunrooms, insulated covers
Solid (flat) Flat single layer, glass-like clarity None Sold by thickness Skylight glazing, canopies

Suntuf is sold 26 inches wide in 6, 8, 10 and 12 foot lengths and 49.6 inches wide in 8, 12 and 16 foot lengths, per Palram’s brochure. Coverage is always less than nominal width because adjacent panels overlap: a 26 inch PVCLite or CoverLite panel covers about 24 inches, so buy for coverage, not for nominal size. Our corrugated roof panel guide has the full size and coverage math.

Clear does not mean cool: light, glare, and heat

A fully clear panel transmits the most daylight, 90% on Suntuf Clear, and the most solar heat and glare with it. Palram’s own guide recommends ventilation on every Suntuf installation to limit heat buildup and condensation, through an open-air side or a powered fan. Tinted panels at 35% to 45% transmission cut glare and heat under a patio roof by passing less of the sun’s energy.

Pick the tint by how the space is used: Clear (90%) for a greenhouse or a north-facing cover that never gets direct sun, White Opal (45%) for even light over a patio or porch, and Bronze or Solar Grey (35%) for west-facing covers. UV protection is separate from tint: Palram’s comparison chart lists 100% UV protection for Suntuf in every color, and the label side must face the sky.

How to install clear roof panels

Clear panels install over a purlin frame with fasteners driven through the crowns of the ribs, and with 1/4 inch pre-drilled holes so the plastic can move. The steps below follow Palram’s Suntuf installation guide; check your panel maker’s guide if you use another brand.

  1. Set a minimum slope. Build at least 1 1/2 inches of fall per 12 inches of run. Below that, Palram calls for additional sealing at the laps.
  2. Space the purlins for the load. 36 inches maximum at 20 psf, 30 inches at 30 psf, 24 inches at 40 psf and 16 inches at 50 psf. Palram recommends 24 inches for most installs.
  3. Face the UV side up. Install the label side toward the sky. Palram warns that reversing it leads to discoloration of the panel.
  4. Pre-drill oversized holes. Use a 1/4 inch bit for Palram Woodtite and Metaltite screws, or drill 1/16 inch over the shank for other fasteners, so thermal movement does not buckle the sheet.
  5. Fasten the crowns. Use 2 inch EPDM-washered fasteners on roofs, through the crown of every other rib along each purlin, and every rib in high-wind areas. Tighten until snug; a deformed washer means the screw is too tight, and Palram says never to use an impact driver.
  6. Close and trim the edges. Use profile-matched closure strips at the top and bottom, keep the eave overhang between 1 and 3 inches, and tape the flute ends of multiwall panels so condensation drains.

How long do clear roof panels last and do they yellow?

Warranty terms are the best published guide to life. Palram backs clear polycarbonate roof panels in its Suntuf line with a limited lifetime warranty against losing more than 10% of light transmission and 10 years against hail, its lighter Suntop line with 10 years, and its Palruf PVC with 5 years. The 8 mm twinwall sheet at Menards lists a 10 year warranty. Fiberglass ages worst: its surface resin erodes to expose glass fibers, which dulls the panel and cuts light over time.

Yellowing is a UV problem. A co-extruded UV layer on the top face is what holds clarity, which is why Palram ties its warranty to label-side-up installation and why uncoated sheets are a false economy. Heat is rarely the failure mode for polycarbonate, which Palram rates for -40°F to 212°F, against -4°F to 120°F for its Palruf PVC. Clean with a lukewarm soapy solution and a soft cloth; Palram says to avoid ammonia-based glass cleaners and abrasive brushes.

Frequently asked questions

What is the best material for clear roof panels?

Corrugated polycarbonate is the best all-round choice for most clear roof jobs. Palram rates Suntuf Clear at 90% light transmission with a limited lifetime warranty against losing more than 10% of that light and a 10 year hail warranty. PVC costs less, about $1.00 per square foot of coverage for a PVCLite panel at Menards in October 2026, but carries a 5 year warranty. Acrylic is clearer but more brittle.

Is bronze or clear polycarbonate better?

It depends on the sun. Palram lists Suntuf Clear at 90% light transmission and Bronze at 35%, so bronze passes well under half the light and much less glare. Use clear for greenhouses and north-facing covers, and bronze, Solar Grey (35%) or White Opal (45%) for patios with direct afternoon sun.

Do clear roof panels get hot underneath?

Yes. A fully clear panel passes about 90% of visible light and the solar heat that comes with it, so a clear patio cover can feel like a greenhouse in direct afternoon sun. Palram recommends ventilation on every Suntuf install, and tinted panels at 35% to 45% transmission stay more comfortable underneath while still admitting daylight.

How long do clear polycarbonate roof panels last?

Palram warrants Suntuf polycarbonate for life against losing more than 10% of its light transmission and for 10 years against hail; its Suntop line carries 10 years and its Palruf PVC 5 years. Actual life depends on keeping the UV-protected label side facing up, the purlin spacing for your snow load and cleaning without ammonia or abrasives.

Do clear roof panels yellow over time?

Panels without a UV layer yellow; UV-protected polycarbonate installed label side up resists it, which is why Palram ties its warranty against more than 10% light loss to correct orientation. Fiberglass is the most prone to discoloring, because its surface resin erodes and exposes the glass fibers, clouding the panel.

What slope do clear roof panels need?

Palram’s Suntuf guide sets a minimum of 1 1/2 inches of fall per 12 inches of run and calls for additional sealing below that. Purlins go no more than 36 inches apart, 24 inches recommended, and closer for snow: 24 inches at 40 psf and 16 inches at 50 psf.

Are clear roof panels cheaper than a skylight?

For an outdoor cover such as a patio, carport or pergola, yes: Menards listed clear PVC at about $1.00 and 8 mm twinwall polycarbonate at about $4.89 per square foot in October 2026, before framing. Over heated living space, a fixed or tubular skylight usually beats a panel roof on insulation and leak risk, so price both.