By The Roofing Brief Team. Last reviewed: October 2026.
Commercial rubber roofing is EPDM (ethylene propylene diene monomer), a single-ply synthetic rubber membrane installed on low-slope and flat commercial roofs. It costs about $3.50 to $10.00 per square foot installed, or $4.50 to $14.00 when tear-off and new insulation are included, per HomeGuide’s rubber roof cost guide. Carlisle sells its Sure-Seal sheet in 45 and 60 mil and its Sure-White sheet in 60 and 90 mil, with manufacturer warranties of up to 30 years depending on thickness and attachment. It competes mainly with TPO, and the pick turns on your deck, your climate zone and whether you need a reflective surface.
What is commercial rubber roofing?
Commercial rubber roofing means an EPDM membrane, a vulcanized synthetic rubber sheet made in large rolls and laid over a flat or low-slope commercial roof in a single layer. GAF’s commercial roofing overview notes that EPDM has been in use since the 1960s, two decades before TPO debuted in the 1980s. It remains one of the most installed low-slope systems. The sheet is governed by ASTM D4637, and Carlisle’s Sure-Seal data sheet (12.03.24) lists a maximum brittleness temperature of minus 49°F and 465% to 480% ultimate elongation, which is why the membrane stays flexible in northern winters.
Black Sure-Seal ships in widths up to 50 feet and lengths up to 200 feet, per the same data sheet, so a crew can cover a large deck with few field seams. Seams are where most single-ply roofs eventually leak. Modern EPDM seams use primer plus splice tape (Carlisle’s Factory-Applied Tape or hand-applied SecurTAPE) rather than the liquid splice adhesives used on early roofs, and Carlisle requires extra heat-gun steps when splicing below 40°F.
How much does commercial rubber roofing cost per square foot in 2026?
Commercial rubber roofing costs roughly $3.50 to $10.00 per square foot installed, and HomeGuide puts commercial roof replacement in general at $4 to $10 per square foot. Membrane material alone runs $0.50 to $3.50 per square foot. The attachment method moves the material line: HomeGuide’s system table shows ballasted 45 mil at $1.60 to $2.50 per square foot and fully adhered 60 to 75 mil at $2.80 to $3.50, before labor. For residential flat roofs, see our EPDM roofing cost guide.
| System | Material cost, 45 mil (per sq ft) | Material cost, 60 to 75 mil (per sq ft) | Max Carlisle warranty wind speed | Source |
|---|---|---|---|---|
| Ballasted EPDM | $1.60 to $2.50 | $2.00 to $2.50 | 80 mph | HomeGuide; Carlisle |
| Mechanically fastened | $1.85 to $2.90 | $2.00 to $3.00 | 90 mph (reinforced Sure-Tough) | HomeGuide; Carlisle |
| Fully adhered | $2.75 to $3.30 | $2.80 to $3.50 | 120 mph (60 and 90 mil Sure-Seal) | HomeGuide; Carlisle |
| Installed total, all systems | $3.50 to $10.00 | n/a | HomeGuide | |
The rest of the bill is tear-off, insulation and labor. HomeGuide’s line items are old roof removal at $1.00 to $2.00 per square foot, membrane at $0.50 to $3.50, insulation or recovery board at $0.50 to $3.00 (1 inch polyiso runs $0.50 to $1.50, 3 inch runs $1.30 to $3.00) and labor at $2.50 to $5.50. For a full breakdown by roof size and mil, see our EPDM rubber membrane pricing by the mil, and compare it against other systems in our commercial roof replacement cost by system guide.
Worked example: a 10,000 square foot warehouse roof
| Line item (HomeGuide) | Low per sq ft | High per sq ft | 10,000 sq ft low | 10,000 sq ft high |
|---|---|---|---|---|
| Old roof removal | $1.00 | $2.00 | $10,000 | $20,000 |
| EPDM membrane | $0.50 | $3.50 | $5,000 | $35,000 |
| Insulation or recovery board | $0.50 | $3.00 | $5,000 | $30,000 |
| Labor | $2.50 | $5.50 | $25,000 | $55,000 |
| Total with tear-off | $4.50 | $14.00 | $45,000 | $140,000 |
| Total as a recover (no removal) | $3.50 | $12.00 | $35,000 | $120,000 |
The recover row simply drops HomeGuide’s removal line. Whether a recover is allowed depends on the existing roof: the International Building Code limits re-covering over roofs that are water-soaked or already carry two layers, so get a core cut and a moisture survey before pricing the cheaper row.
What are the three ways to install commercial EPDM?
Commercial EPDM is installed ballasted, mechanically attached or fully adhered, and the choice sets both the cost and the maximum warranted wind speed. In Carlisle’s warranty availability quick reference (07.31.24), ballasted Sure-Seal tops out at 80 mph, mechanically fastened Sure-Tough at 90 mph and adhered 60 or 90 mil Sure-Seal at 120 mph.
- Ballasted: the membrane and insulation are loose-laid and held down with a minimum of 10 lb of ballast per square foot, per Carlisle’s Sure-Seal data sheet (Design B). The deck must carry that added dead load, and Carlisle caps ballasted warranty wind coverage at 80 mph.
- Mechanically attached: the membrane is fastened through plates and screws along the seams, and the next sheet laps over the fastener row. Carlisle uses its reinforced Sure-Tough sheet for this, with warranties of 15 years at 45 mil, 20 years at 60 mil and 30 years at 75 mil.
- Fully adhered: the entire sheet is glued to the insulation or cover board with bonding adhesive. Carlisle offers adhered 60 mil Sure-Seal for up to 25 years and 90 mil for up to 30 years at 120 mph, the highest wind coverage of the three, at the highest material cost.
Which commercial EPDM system fits your building?
| If your building has | Choose | Threshold and source |
|---|---|---|
| A structural deck that can take at least 10 psf of added dead load, and warranty wind needs of 80 mph or less | Ballasted 45 or 60 mil EPDM | Minimum 10 lb ballast per sq ft; 80 mph max (Carlisle) |
| A light steel deck and a re-roof schedule to keep | Mechanically fastened reinforced EPDM | Up to 90 mph, 15 to 30 years by thickness (Carlisle) |
| A warranty wind requirement above 90 mph, or an exposed or irregular roof | Fully adhered 60 or 90 mil | Up to 120 mph (Carlisle) |
| Hail exposure and a need for written hail coverage | Adhered 90 mil over an approved adhered cover board | 2 inch hail at 90 mil vs 1 inch at 60 mil; cover board such as min. 1/2 in DensDeck Prime required (Carlisle) |
| A hot climate where the energy code requires a cool roof | White EPDM or white TPO | Black Sure-Seal SRI 9; Sure-White 3 year aged SRI 87 (Carlisle data sheets) |
| Heavy rooftop foot traffic around equipment | 90 mil, plus walkway pads | 90 mil Sure-White weighs 0.60 lb/sq ft vs 0.39 lb for 60 mil Sure-Seal (Carlisle) |
What thickness of EPDM should a commercial building use?
Commercial EPDM comes in 45, 60 and 90 mil, and 60 mil is the usual specification for commercial buildings. A mil is one thousandth of an inch, so 60 mil is 0.060 inch, and Carlisle holds thickness to plus or minus 10%. Thicker membrane resists punctures and foot traffic better and unlocks longer warranty terms and hail coverage, at a higher price per square foot.
| Thickness | Weight (lb/sq ft) | Max warranty, adhered | Max warranty, ballasted | Hail coverage (adhered) | Source |
|---|---|---|---|---|---|
| 45 mil | 0.29 (Sure-Seal) | 15 years, 90 mph | 25 years, 80 mph | None | Carlisle PDS and warranty reference |
| 60 mil | 0.39 (Sure-Seal) | 25 years, 120 mph | 30 years, 80 mph | 1 inch | Carlisle PDS and warranty reference |
| 90 mil | 0.60 (Sure-White) | 30 years, 120 mph | 30 years, 80 mph | 2 inch | Carlisle PDS and warranty reference |
These ceilings come from Carlisle’s warranty availability quick reference (07.31.24), which lists 15 years for adhered or mechanically fastened 45 mil sheet and 25 years for ballasted 45 mil Sure-Seal. Other manufacturers publish their own terms, so ask each bidder for the maker’s table. For a gauge-by-gauge breakdown, see our guide to EPDM thickness, tolerance and warranty by mil.
How long does a commercial rubber roof last?
HomeGuide lists a life expectancy of 15 to 25 years for EPDM, and Carlisle warrants its thicker systems for up to 30 years, so on a 60 or 90 mil roof under a full system warranty the maker carries covered leak repairs for that whole term. EPDM ages slowly in the field: the Sure-Seal sheet passes ASTM D1149 ozone testing with no cracks. The usual failure points are seams, flashings and penetrations, so schedule a spring and fall inspection of those three details. For field lifespan data across membranes, see our 2026 roofing material lifespan report.
Black vs white EPDM: the cooling-load tradeoff
Standard black EPDM has a solar reflectance index of 9 on Carlisle’s Sure-Seal data sheet, so it absorbs most solar heat. Carlisle’s Sure-White data sheet (12.10.24) lists an initial solar reflectance of 0.79, a 3 year aged value of 0.71 and a 3 year aged SRI of 87. White EPDM comes in narrower sheets (60 mil up to 20 feet wide, 90 mil up to 10 feet) than the 50 foot black sheet, which means more field seams per roof.
Carlisle’s own literature states that a heating penalty can outweigh the cooling benefit of a white roof in central and northern climates. Use that as the decision rule: in climate zones where your adopted energy code requires a cool low-slope roof (IECC section C402.3 for commercial buildings), black EPDM will not meet the aged reflectance requirement, so price white EPDM against white TPO. In heating-dominated climates, black EPDM is the default. Product ratings can be checked in the Cool Roof Rating Council directory.
When does commercial rubber roofing beat TPO?
Commercial rubber roofing (EPDM) beats TPO when you need cold-weather flexibility, the longest field track record or a low-cost ballasted system on a strong deck. The EPDM sheet standard (ASTM D4637) sets a minus 49°F brittleness test, against minus 40°F in the TPO standard (ASTM D6878), and Carlisle’s Sure-White data sheet reports EPDM staying flexible down to minus 40°F in torsion testing. TPO usually wins when the priority is a white cool roof or heat-welded seams. Our EPDM vs TPO roof guide compares cost and lifespan for each. For the chemistry behind the name, see our explainer on what EPDM stands for.
| Priority | Better pick | Why | Source |
|---|---|---|---|
| Reflective cool roof | TPO | White Sure-Weld TPO: initial SR 0.79, SRI 99; white is standard stock | Carlisle TPO PDS |
| Cold-climate flexibility | EPDM | Standard brittleness test minus 49°F (ASTM D4637) vs minus 40°F (ASTM D6878) | Carlisle PDS |
| Lowest install cost on strong deck | EPDM ballasted | Ballasted 45 mil material $1.60 to $2.50/sq ft; no adhesive or welding | HomeGuide |
| Long field track record | EPDM | In use since the 1960s; TPO since the 1980s | GAF |
| Seam method | TPO | Hot-air welded seams; EPDM uses primer and tape | Carlisle PDS |
For the full side-by-side, read our TPO vs EPDM roofing comparison, and see where both sit among low-slope options in our single-ply roofing guide.
Warranties on a commercial rubber roof
Commercial EPDM carries two warranty types: a manufacturer material warranty and, for larger projects, a No Dollar Limit (NDL) system warranty. An NDL warranty covers both materials and labor to repair a covered leak with no cap on the payout, but it is only issued when a manufacturer-authorized contractor installs an approved assembly. Material-only warranties cover the membrane sheet, not the labor to fix a failure.
Four numbers on the warranty matter more than its length, and Carlisle publishes all four by system: maximum wind speed (80 to 120 mph), maximum hail diameter (none to 3 inches on FleeceBACK), accidental puncture labor hours (8 to 32 hours on some sheets) and the required cover board for hail coverage. Ask each bidder for those four values in writing, plus the maintenance and inspection records the warranty requires.
Frequently asked questions
How much does commercial rubber roofing cost per square foot?
Commercial rubber roofing (EPDM) costs about $3.50 to $10.00 per square foot installed, per HomeGuide, or $4.50 to $14.00 with tear-off and new insulation. Membrane material alone runs $0.50 to $3.50 per square foot. Ballasted systems carry the lowest material cost ($1.60 to $2.50 at 45 mil) and fully adhered the highest ($2.80 to $3.50 at 60 to 75 mil).
How long does a commercial rubber roof last?
HomeGuide lists a 15 to 25 year life expectancy for EPDM, and Carlisle warrants adhered 60 mil Sure-Seal for up to 25 years and 90 mil for up to 30 years. Most failures start at seams, flashings and penetrations, so spring and fall inspections of those details are the main lever on service life.
Is EPDM or TPO better for a commercial building?
Neither wins everywhere. the EPDM standard sets a colder brittleness test (minus 49°F vs minus 40°F for TPO), EPDM has a field record back to the 1960s and cheap ballasted installs on strong decks. White TPO wins where the energy code requires a cool roof, with an initial SRI of 99 on Carlisle’s Sure-Weld sheet, and where heat-welded seams are preferred.
What are the three ways to install commercial EPDM?
Commercial EPDM is installed ballasted, mechanically attached or fully adhered. Ballasted is loose-laid under at least 10 lb of stone or pavers per square foot with 80 mph maximum warranty wind coverage. Mechanically attached uses plates and screws at up to 90 mph. Fully adhered is glued across the whole surface and carries up to 120 mph coverage, per Carlisle.
What thickness of EPDM should a commercial roof use?
Most commercial buildings specify 60 mil EPDM, which Carlisle warrants for up to 25 years adhered with 1 inch hail coverage. Use 45 mil only on budget, low-traffic roofs (15 years adhered), and 90 mil for high-traffic decks or hail regions, where Carlisle offers 30 years and 2 inch hail coverage over an approved cover board.
Can EPDM be installed in cold weather?
Yes. Sure-Seal EPDM has a maximum brittleness temperature of minus 49°F, so the sheet stays workable in winter. The seam materials are the limit: Carlisle requires extra steps for splicing below 40°F, including warming the primed splice area with a hot-air gun before rolling the tape, so confirm the winter procedure with the manufacturer’s spec.
For the wider picture on flat commercial systems, start with our commercial roofs overview for 2026.