Subscribe

MATERIALS · July 31, 2026

Rolled Roofing vs Shingles: Cost, Lifespan, and Slope

Rolled roofing costs $2 to $5.50 per sq ft installed vs $5 to $8 for architectural shingles, but lasts 5 to 10 years against 15 to 30. Compare by slope.

By The Roofing Brief Team. Last reviewed: October 2026.

Rolled roofing costs $2.00 to $5.50 per square foot installed, or $200 to $550 per 100 sq ft square, per HomeGuide’s roll roofing cost guide, against about $4 to $6 for 3-tab and $5 to $8 for architectural asphalt shingles in our 2026 roofing cost report. Rolled roofing is the cheaper, faster, shorter-lived option; asphalt shingles cost more up front but last 15 to 30 years against 5 to 10 and are the only one most homeowners want on a visible house roof. Mineral-surfaced roll (MSR) lasts 5 to 10 years per HomeGuide, while asphalt shingles last 15 to 20 years (3-tab) or 20 to 30 years (architectural). The right pick comes down to three thresholds: roof slope (below 2:12, shingles are not allowed), how many years you need, and whether the roof is visible.

Rolled roofing vs shingles at a glance

The two products are both asphalt based, but they differ on cost, lifespan, and where the 2021 International Residential Code (IRC) lets you install them. Each row below names its source; the product examples are Tarco Fiberglass Mineral Surfaced Roll Roofing and Owens Corning Supreme 3-tab, chosen because both makers publish full data sheets.

Factor Rolled roofing (MSR) Asphalt shingles Source
Installed cost per sq ft $2.00 to $5.50 $4 to $6 (3-tab); $5 to $8 (architectural) HomeGuide; TRB 2026 cost report
Installed cost per square (100 sq ft) $200 to $550 $400 to $600 (3-tab); $500 to $800 (architectural) Same, times 100
Material cost $40 to $50 per MSR roll; $0.50 to $1.50 per sq ft $80 to $130 per square (3-tab); $100 to $250 (architectural) HomeGuide
Typical lifespan 5 to 10 years 15 to 20 years (3-tab); 20 to 30 years (architectural) HomeGuide
Minimum roof slope 1:12 (8 percent) 2:12, with double underlayment from 2:12 up to 4:12 IRC R905.5.2, R905.2.2
Material standard ASTM D3909 or ASTM D6380 Class M ASTM D3462; wind per ASTM D7158 or D3161 IRC R905.5.4, R905.2.4
Size and weight 36 in x 36 ft, 108 sq ft gross, 72 lb nominal (Tarco) 12 x 36 in, 5 in exposure, 80 shingles in 3 bundles per square (OC Supreme) Maker data sheets
Manufacturer warranty Free from manufacturing defects only (Tarco) 25-year limited, 60 mph wind, 10-year algae (OC Supreme); lifetime limited on most architectural lines Maker data sheets
Colors 9 at Tarco (White, Black, Cedar Blend, Weatherwood, Dark Brown, Red, Hickory, Slate Grey, Green) 19 on GAF Timberline HDZ alone Maker pages
Best fit Sheds, garages, barns, porches, low-slope outbuildings Houses and any roof you want to last Editorial

Slope minimums and material standards follow the 2021 IRC, Chapter 9, Sections R905.2 and R905.5; your local code edition and amendments govern. Treat every price as a planning range, not a quote.

Cost: what each one runs per square

Rolled roofing is the lower-cost material by a wide margin. HomeGuide puts MSR at $0.50 to $1.50 per square foot for material plus $1.50 to $4.50 for labor, $2.00 to $5.50 installed, with old roof removal adding $1 to $2 per square foot. Today’s Homeowner (updated April 2025) quotes $30 to $100 per square for material, $1.50 to $3.00 per square foot for labor, and $1,500 to $3,000 for a typical job. Asphalt shingles run $4 to $6 per square foot installed for 3-tab and $5 to $8 for architectural, per our cost report.

Rolled roofing cost by roof size, set against architectural shingles:

Roof area Rolled roofing installed ($2.00 to $5.50 per sq ft) Architectural shingles ($5 to $8 per sq ft)
200 sq ft (small shed) $400 to $1,100 $1,000 to $1,600
500 sq ft (2-car garage) $1,000 to $2,750 $2,500 to $4,000
1,000 sq ft $2,000 to $5,500 $5,000 to $8,000
1,500 sq ft $3,000 to $8,250 $7,500 to $12,000
2,000 sq ft $4,000 to $11,000 $10,000 to $16,000

Small jobs often hit a contractor’s minimum charge, so a 200 sq ft shed can price above the per-foot math. For a DIY shed, the material bill is small: a 200 sq ft roof needs 2 rolls of 100 sq ft coverage, plus a third roll for 2-inch side laps, 4-inch end laps and cut-offs, so 3 rolls at HomeGuide’s $40 to $50 per MSR roll comes to $120 to $150 before nails and lap cement.

The gap narrows once lifespan enters the math. Divide installed cost by service life: rolled roofing at $2.00 to $5.50 over 5 to 10 years works out to $0.20 to $1.10 per square foot per year, while architectural shingles at $5 to $8 over 20 to 30 years work out to about $0.17 to $0.40. A rolled roof replaced every 6 to 8 years can cost more across 20 years than a single shingle roof that lasts the whole span. For a like-for-like picture across materials, see our breakdown of roof cost by material.

Lifespan: how long each lasts

Asphalt shingles outlast rolled roofing by a large margin. HomeGuide lists felt and MSR sheets at 5 to 10 years and Today’s Homeowner at five to eight years, and Tarco’s data sheet warrants its MSR only against manufacturing defects. Asphalt shingles last 15 to 20 years for 3-tab and 20 to 30 years for architectural, per HomeGuide’s roof replacement guide, and carry limited warranties such as the 25-year term on Owens Corning Supreme.

The reason is thickness and layering. A shingle roof is two layers deep at nearly every point because each course covers the one below with only a 5-inch exposure (OC Supreme), while rolled roofing is a single 72-lb sheet per 108 sq ft (Tarco) with only a 2-inch side lap between courses. Sun, thermal cycling, and standing water wear that single ply faster. In harsh climates the low end of each range is the safer planning assumption.

Slope: where each one is allowed to go

Roof slope often decides the choice before cost does. IRC Section R905.5.2 allows mineral-surfaced roll roofing on slopes down to 1:12, which is why it appears on low-slope sheds, porches, and additions where shingles are not permitted. Asphalt shingles are a steeper-slope product: IRC Section R905.2.2 permits them only on slopes of 2:12 or greater and requires double underlayment from 2:12 up to 4:12. As an alternative, IRC R905.1.1 allows a self-adhering ASTM D1970 underlayment installed per both the underlayment and shingle manufacturers’ instructions. At 4:12 and steeper, a single underlayment layer is the code baseline. Our underlayment slope requirements page lays out the double-layer method.

If your roof sits below 2:12, shingles are off the table and rolled roofing (or a true low-slope membrane) is the realistic path. Below 1:12, MSR is off the table too. For very low or flat decks, a single-ply or self-adhered system usually outperforms roll roofing; compare peel-and-stick roofing and SBS modified bitumen before defaulting to MSR. Multi-ply low-slope systems start with a fastened first layer, explained in our guide to base sheet roofing.

Installation and DIY difficulty

Rolled roofing is the easier material for a determined DIYer, which is part of its appeal on outbuildings. Rolls weigh about 75 pounds and cover 100 square feet each, per HomeGuide (Tarco lists 72 lb for 108 sq ft gross). Shingles take longer because each course is placed and fastened individually, with at least 4 nails per strip shingle under IRC R905.2.6, and detail work at valleys, hips, and penetrations adds skill and time.

The mechanically fastened method from Tarco’s MSR application instructions, step by step:

  1. Unroll the sheet and let it relax in direct sunlight, then cut it into 12 to 18 ft lengths.
  2. Lay the first full-width sheet horizontally with its edges flush to the eave and rakes.
  3. Nail with galvanized #11 or #12 roofing nails at least 1 inch long with 3/8-inch heads, long enough to penetrate the deck: 9 inches on center in the center of the lap area, plus two staggered rows 18 inches on center, 12 inches in from each edge in the field.
  4. Lap each next course at least 2 inches on side laps and 4 inches on end laps, and stagger end laps at least 3 feet course to course.
  5. Set laps in a thin, even layer of ASTM D3019 lap cement (excess cement blisters the sheet), press until a small bead shows, then roll the lap.
  6. Cover every nail; Tarco says any exposed nail head gets asphalt roof cement.

Two cautions apply. Rolled roofing is stiff when cold, and Tarco’s sheet is tested to unroll at 50°F (ASTM D3909), so a day at or above about 50°F is a practical floor for laying it. Seams are the most common failure point, so lap width and cement coverage matter more than speed. If you are weighing a self-install on a house roof, read our honest take on what rolled roofing actually is and where it holds up before committing.

Curb appeal and resale

Shingles win decisively on looks and resale, and this is why rolled roofing rarely appears on a visible house roof. HomeGuide notes rolled roofing is “often considered unattractive for homes and may decrease resale values” and is not allowed in some HOAs. Tarco offers MSR in 9 colors; GAF sells its Timberline HDZ architectural shingle in 19, in shadow-lined profiles that buyers and appraisers treat as the expected residential material.

On a shed, garage, or barn the appearance trade is easy to accept for savings of roughly $3 per square foot against architectural shingles at the midpoints of the ranges above. On a home that you plan to sell, a rolled roof can read as a deferred-maintenance signal. If you want shingle looks with longer life, our comparison of rubber shingles versus asphalt shingles covers a durable middle path.

How to decide: a simple framework

Work through these questions in order. The first one that gives a hard answer usually settles the decision.

If Choose Rule or number behind it
Slope is below 1:12 A low-slope membrane (SBS, TPO, EPDM), not MSR or shingles IRC R905.5.2 bars MSR below 1:12
Slope is 1:12 to under 2:12 Rolled roofing or a membrane IRC R905.2.2 bars shingles below 2:12
Slope is 2:12 to under 4:12, house roof Shingles over double underlayment (or ASTM D1970) IRC R905.2.2 and R905.1.1
Slope is 4:12 or steeper, house roof Shingles Single underlayment layer is the code baseline
Outbuilding needed for under 8 years Rolled roofing MSR lasts 5 to 10 years at $2.00 to $5.50 per sq ft
Roof must last 10 years or more Shingles $0.17 to $0.40 per sq ft per year vs $0.20 to $1.10 for MSR
DIY on a small outbuilding Rolled roofing About 75 lb rolls, 2 in side laps, 4 in end laps
  1. What is the roof slope? Below 2:12, shingles are not code-compliant; use rolled roofing or a low-slope membrane. From 2:12 up to 4:12, shingles need double underlayment. At 4:12 or steeper, shingles are the default.
  2. Is it a house or an outbuilding? On a visible house roof, choose shingles for 15 to 30 years of life and resale. On a shed, garage, or barn, rolled roofing at $2.00 to $5.50 per square foot is a reasonable budget call.
  3. How long do you need it to last? Under 8 years, rolled roofing can pencil out. Ten years or more, shingles almost always cost less per year of service.
  4. What is the budget today versus over 20 years? If cash today is the only constraint, rolled roofing wins the first invoice. If lowest lifetime cost matters, shingles usually win.
  5. Who is installing it? A confident DIYer can handle 3 to 5 rolls of MSR on a small low-slope structure. A house roof of 15 to 25 squares is a job for a professional shingle crew.

The verdict

For a house, asphalt shingles are the better buy in nearly every case: 15 to 30 years of life against 5 to 10, 25-year to lifetime limited warranties, better looks, and stronger resale outweigh the higher first cost of $5 to $8 per square foot. For a low-slope shed, garage, barn, or short-term structure where budget rules and the roof is out of sight, rolled roofing is a defensible pick that gets you covered quickly and cheaply. The deciding factors are slope, how long the roof must last, and whether anyone will see it.

Put simply, choose rolled roofing when a slope between 1:12 and 2:12 forces it or when a cheap, short-lived cover on an outbuilding is the goal, and choose shingles for any roof you want to last a generation.

Frequently asked questions

How much does rolled roofing cost?

Rolled roofing costs $2.00 to $5.50 per square foot installed, or about $200 to $550 per 100 sq ft square, per HomeGuide, with material at $0.50 to $1.50 per square foot and an MSR roll at $40 to $50. Today’s Homeowner puts a typical job at $1,500 to $3,000. Removing an old roof adds $1 to $2 per square foot per HomeGuide.

Is rolled roofing cheaper than shingles?

Yes, up front. Rolled roofing runs $2.00 to $5.50 per square foot installed per HomeGuide, while 3-tab shingles run about $4 to $6 and architectural shingles $5 to $8 per our 2026 cost report. Per year of service the order often flips: about $0.20 to $1.10 per square foot per year for MSR against $0.17 to $0.40 for architectural shingles.

How long does rolled roofing last compared to shingles?

Rolled roofing generally lasts 5 to 10 years per HomeGuide (five to eight per Today’s Homeowner), often with only a manufacturing-defect warranty. Asphalt shingles last 15 to 20 years for 3-tab and 20 to 30 years for architectural, per HomeGuide. Harsh climates and standing water push both products toward the low end of their ranges.

Can you put rolled roofing on a house?

You can where slope is 1:12 or more, since IRC R905.5.2 allows it, but it is uncommon on visible house roofs because of its 5 to 10 year lifespan and flat look. Rolled roofing is best suited to sheds, garages, barns, and low-slope additions. HomeGuide notes it may decrease resale value and is not allowed in some HOAs.

What is the lowest slope for shingles versus rolled roofing?

Under IRC R905.2.2, asphalt shingles are permitted on slopes of 2:12 or greater, with double underlayment (or a self-adhering ASTM D1970 underlayment as the R905.1.1 alternative) required from 2:12 up to 4:12. Mineral-surfaced roll roofing is permitted down to 1:12 under IRC R905.5.2, which is why it appears on low-slope structures where shingles are not permitted.

Does rolled roofing leak more than shingles?

Rolled roofing relies on narrow laps (2 inches on the sides and 4 inches at the ends in Tarco’s instructions), and those laps are its most common failure point, so poor installation can leak sooner than a shingle roof. Full, thin lap cement coverage to ASTM D3019 reduces the risk. Shingles shed water through many small overlaps and generally hold up longer, especially on slopes of 4:12 and steeper.

Is rolled roofing a good DIY project?

For a small, low-slope shed or garage, rolled roofing is one of the more DIY-friendly materials. Rolls weigh about 75 pounds and cover 100 square feet, and Tarco’s method needs only roofing nails, lap cement, a knife and a roller. Lay it on a day at or above about 50°F, since cold sheets are stiff and can crack, and keep 2-inch side and 4-inch end laps at every seam.