Subscribe

MATERIALS · July 17, 2026

Peel and Stick Roofing: Cost, Products, and Where It Works

Peel and stick roofing costs about $2.05 per sq ft in MFM Peel & Seal rolls (Oct 2026). Slope limits, 55°F install rule, lifespan and GAF Liberty compared.

By The Roofing Brief Team. Last reviewed: October 2026.

Peel and stick roofing is a self-adhesive membrane that bonds to a clean surface when you pull off its release liner, no torch, hot asphalt, or fasteners required. It works well on low-slope sheds, RVs, mobile homes, porches, dormers, and as flashing, and it fails on steep or primary house roofs it was never designed for. MFM Peel & Seal, the single-layer benchmark, listed at $204.99 for a 36 in x 33.5 ft (100 sq ft) roll at Best Materials on October 19, 2026, about $2.05 per square foot, while a two-ply GAF Liberty system ran about $2.08 per square foot in rolls at Builders Warehouse that day.

“Peel and stick” names two different products: an exposed roofing membrane such as Peel & Seal or Liberty, and a peel-and-stick underlayment that goes under shingles or metal. The underlayment is the “self-adhering polymer-modified bitumen sheet” meeting ASTM D1970 that 2021 IRC Section R905.1.2 allows as an ice barrier, and it is not built to sit in the sun.

What is peel and stick roofing?

Peel and stick roofing is a rolled, self-adhering membrane of rubberized asphalt or SBS modified bitumen with a release liner on the back. MFM’s Peel & Seal technical data sheet (revised 08/23) describes aluminum foil laminated to a cross-laminated polyethylene film over a thick layer of rubberized asphalt, 45 mils nominal (ASTM D5147), tested to ASTM D1970 and evaluated under ICC-ES ESR-1654. You peel the liner, press the sheet down and roll it; no flame and no separate adhesive.

Most rolls carry a top surface of either smooth aluminum foil or granules. Aluminum-faced MFM Peel & Seal reflects heat and comes in 3, 4, 6, 9, 12, 18 and 36 in widths, all 33.5 ft long. Granulated self-adhering cap sheets include GAF Liberty Cap and LeakBarrier EasyStick Plus, which Menards lists as an SBS modified, polyester-reinforced, granule-surfaced cap sheet in a 36 in x 36 ft roll covering 100 sq ft. Narrow 3 to 12 in widths exist for flashing and seam work.

Peel and stick roofing products and 2026 prices

Peel and stick roofing ran about $2.05 to $2.08 per square foot in rolls on October 19, 2026: $204.99 for a 100 sq ft MFM Peel & Seal roll, and $142.60 for a 200 sq ft GAF Liberty Base/Ply roll plus $137.11 for a 100 sq ft Liberty Cap roll at Builders Warehouse. Side laps take 8 to 10 percent of each roll’s width (3 of 36 in on Peel & Seal, 4 of 39-3/8 in on Liberty Cap), so buy by net coverage. Roll specs below are from each maker’s data sheet or retailer listing.

Product Type / surface Roll size Coverage Price seen Oct 19, 2026 Best use Source
MFM Peel & Seal (aluminum, 50036) Rubberized asphalt, aluminum foil face, 45 mil 36 in x 33.5 ft 100 sq ft $204.99 (list $308.00) Flashing, RVs, mobile homes, sunrooms MFM data sheet; Best Materials
LeakBarrier EasyStick Plus SBS self-adhering granulated cap sheet, polyester reinforced 36 in x 36 ft 100 sq ft Check local Menards price Shed and outbuilding roofs Menards listing
GAF Liberty SA Base/Ply SBS self-adhering base sheet 39-3/8 in x 66 ft 2 squares excluding laps $142.60 First ply of a rated low-slope system GAF data sheet; Builders Warehouse
GAF Liberty SA Cap SBS self-adhering granulated cap, ASTM D6164 Type I 39-3/8 in x 34 ft 1 square $137.11 Finished ply of a rated low-slope system GAF sell sheet; Builders Warehouse

Material is only part of the number. HomeGuide’s flat roof cost guide (November 5, 2025) prices installed modified bitumen, which it notes many brands sell as self-adhesive rolls, at $4.00 to $7.50 per square foot and flat-roof labor at $2.00 to $4.50 per square foot. The worked example below prices the rolls for a 10 x 12 ft (120 sq ft) shed roof.

Shed roof, 120 sq ft Net coverage per roll Rolls needed Roll cost Source
MFM Peel & Seal, 1 ply 33 in net width (3 in side lap) x 33.5 ft = about 92 sq ft 2 $409.98 MFM lap rule; Best Materials price
GAF Liberty, 2 ply Base: 2 squares; Cap: about 1 square after laps 1 base + 2 cap $416.82 GAF roll data; Builders Warehouse prices

Where peel and stick roofing actually works

Peel and stick roofing works on small low-slope surfaces and as detail flashing, inside the slope and size limits the makers print. MFM requires a minimum slope of 1/2 in per foot for Peel & Seal and says it is not intended for ponding water or heavy foot traffic. GAF’s Liberty one-ply instructions cover carports, garages, porches and sheds of 2,000 sq ft or less at slopes of 1/2:12 to 6:12, and its two-ply instructions (RESLB504) cover 1/4:12 to 3:12 on roofs of 2,500 sq ft or less.

Good applications

  • Sheds and outbuildings. A low-slope shed or garden building is the textbook fit, cheap to cover and easy to reach.
  • RVs, campers, and trailers. The aluminum-faced membrane bonds to existing metal or fiberglass and reflects heat.
  • Mobile and manufactured homes. Common for recovering flat or low-slope mobile home roofs.
  • Flashing and detail work. Narrow rolls seal around vents, chimneys, skylights, ducts, and wall junctions.
  • Seam and leak repair. A fast patch over a failed seam or a puncture on an existing low-slope roof.
  • Emergency and temporary cover. Quick weatherproofing on a construction site or after storm damage.

Where it fails

  • Primary sloped house roofs. GAF limits Liberty one-ply to 6:12 and 2,000 sq ft and two-ply to 3:12, so a 7:12 or steeper house roof falls outside both.
  • Cold or damp installs. MFM’s data sheet calls for air and surface at 55°F or above, and its adhesion to plywood drops from 51 lb/ft at 75°F to 14 lb/ft at 40°F. GAF’s Liberty range is 45°F to 95°F.
  • Dirty or dusty substrates. Adhesive fails on anything it cannot key into. Priming or thorough cleaning is not optional.
  • Ponding water. MFM states Peel & Seal is not intended for areas with ponding water; standing water finds the laps.
  • Long-term exposed roofs expecting shingle life. MFM’s warranty is 10 years against leaks from material defects, against 25 years on a basic 3-tab shingle.

How long does peel and stick roofing last?

Peel and stick roofing lasts about as long as its warranty and its install allow: MFM warrants Peel & Seal for 10 years against leaks from material or manufacturing defects, and GAF’s Liberty warranty reference sheet (RESLB505) lists 10, 15 or 20 years against manufacturing defects depending on the system. HomeGuide gives modified bitumen roofs, the family Liberty belongs to, 10 to 20 years.

Lifespan swings on product, install temperature and exposure. MFM rates Peel & Seal for service from -20°F to 170°F, but its bond to plywood at 40°F is barely a quarter of the bond at 75°F, so a cold install starts weak. A granulated cap shields the asphalt from UV, and a shaded shed roof runs cooler than an RV roof in full sun. For how each roofing material ages against its marketing, see our roofing material lifespan report.

Peel and stick roofing vs the alternatives

Against torch-down, rolled roofing and EPDM, peel and stick trades lifespan for safety and ease of install: it is the only option here a homeowner can put down with a utility knife and a roller. HomeGuide gives EPDM 15 to 25 years and modified bitumen 10 to 20, against MFM’s 10-year Peel & Seal warranty, so a lasting flat roof points to EPDM or a two-ply modified bitumen system.

Option Install method DIY friendly Life or warranty Material per sq ft Installed per sq ft Source
Peel and stick, single layer (MFM Peel & Seal) Self-adhesive, no heat Yes 10-year limited warranty About $2.05 Not published MFM; Best Materials, Oct 19, 2026
Self-adhering SBS, 2 ply (GAF Liberty) Self-adhesive, layered Moderate 10 to 20-year manufacturing-defect warranty by system About $2.08 $4.00 to $7.50 (modified bitumen) GAF; Builders Warehouse; HomeGuide
Torch-down modified bitumen Open-flame torch No 10 to 20 years $0.70 to $2.20 $4.00 to $7.50 HomeGuide, Nov 5, 2025
Rolled asphalt roofing Nails and lap cement Yes 5 to 20 years $0.15 to $0.50 $2.00 to $5.00 HomeGuide, Nov 5, 2025
EPDM rubber membrane Glued or ballasted Moderate 15 to 25 years $0.50 to $2.50 $3.50 to $10.00 HomeGuide, Nov 5, 2025

Code sets the slope floor for each: 2021 IRC Section R905.11.1 allows modified bitumen down to 1/4:12, R905.5.2 keeps mineral-surfaced roll roofing at 1:12 or steeper, and R905.2.2 starts asphalt shingles at 2:12. Weigh these in our guide to low-slope roof materials, and see what rolled roofing is and where it works.

Which peel and stick product fits your job?

Match the product to slope, size and temperature before you buy. Each row below is a published limit from the maker’s sheet or the 2021 IRC.

If your job is Choose Threshold or rule Source
RV, trailer, mobile home or sunroom roof MFM Peel & Seal Slope at least 1/2 in per foot; no ponding water MFM data sheet
Porch, carport, garage or shed up to 2,000 sq ft GAF Liberty one-ply Slope 1/2:12 to 6:12; back-nail the cap above 1:12 GAF Liberty one-ply instructions
Low-slope roof up to 2,500 sq ft that must last GAF Liberty two-ply Slope 1/4:12 to 3:12 GAF Liberty two-ply instructions (RESLB504)
Ice-dam protection under shingles or metal Peel-and-stick underlayment, not roofing ASTM D1970 sheet from the eave to 24 in inside the exterior wall line IRC R905.1.2
Main roof steeper than 6:12 Shingles or metal, not a membrane Liberty one-ply stops at 6:12 GAF Liberty one-ply instructions
Air or deck below 55°F Wait, or use a product rated colder MFM 55°F minimum; Liberty 45°F to 95°F MFM; GAF
Existing shingles in place Tear off first Surface must be clean, smooth and dry MFM data sheet

How to install peel and stick roofing

Installing peel and stick roofing comes down to a clean surface at 55°F or warmer, careful liner removal, firm rolling, and the lap widths printed on the product. The steps below follow MFM’s Peel & Seal data sheet for a single layer on a small low-slope surface such as a shed; GAF Liberty uses its own primer and lap rules, noted where they differ.

  1. Check the temperature. Air and surface at 55°F or above for MFM Peel & Seal; 45°F to 95°F for GAF Liberty.
  2. Clean and dry the deck. Sweep off all dust and debris, remove old loose material, and let any moisture dry completely.
  3. Prime if required. MFM requires an MFM-approved primer on masonry, concrete, weathered OSB and wood, and rusted metal; GAF calls for ASTM D41 asphalt primer on Liberty decks. Let it dry.
  4. Dry-fit the first course. Roll out the sheet along the lowest edge and trim to length before you peel anything.
  5. Peel and press. Pull the release liner back a foot at a time, set the membrane, and press as you go; for MFM Peel & Seal, the data sheet calls for maximum uniform pressure with a large push or hand roller.
  6. Roll it firmly. Work a hand roller across the whole sheet to seat the adhesive and force out bubbles.
  7. Overlap each course. MFM requires 3 in side laps and 6 in end laps; GAF Liberty Cap uses 4 in side laps and 6 in end laps, with end laps in consecutive courses offset at least 18 in.
  8. Detail the edges and penetrations. Wrap edges, seal around vents and walls with matching flashing, and roll every seam again.

Peel and stick roofing vs peel and stick underlayment

Peel and stick roofing is a finished, exposed surface, while peel and stick underlayment is a hidden layer under shingles or metal. The underlayment is the ASTM D1970 self-adhering sheet that IRC R905.1.2 allows as an ice barrier from the eave to 24 in inside the exterior wall line (36 in along the slope on roofs of 8:12 or steeper). It is designed to be covered by the roofing, while MFM markets Peel & Seal as designed to be left exposed indefinitely.

If you need that ice-and-water layer under a shingle or metal roof, read our guide to peel-and-stick roof underlayment, which covers ASTM D1970 products by name. For how these layers fit into a full roof assembly, start at our learn about roofing hub.

Frequently asked questions

How long does peel and stick roofing last?

Expect roughly 10 to 20 years. MFM warrants Peel & Seal for 10 years against leaks from material defects, GAF lists 10, 15 or 20-year manufacturing-defect warranties on Liberty systems depending on the system, and HomeGuide gives modified bitumen roofs 10 to 20 years. A warm, clean install and a granulated cap push a roof toward the top of that range.

Is peel and stick roofing any good?

Peel and stick roofing is good inside its published limits: MFM Peel & Seal on slopes of at least 1/2 in per foot, and GAF Liberty on porches, garages and sheds up to 2,000 sq ft at 1/2:12 to 6:12. It needs no torch and installs fast. It is a poor choice as the main roof on a sloped house, where shingles last longer.

Can you use peel and stick roofing on a house?

Yes, on low-slope sections such as a porch, dormer or flat addition, and for flashing. GAF’s two-ply Liberty system covers 1/4:12 to 3:12 roofs of 2,500 sq ft or less, and its one-ply system covers 1/2:12 to 6:12 up to 2,000 sq ft. It is not meant as the primary roof on a standard steep house roof.

How much does peel and stick roofing cost?

On October 19, 2026, a 100 sq ft MFM Peel & Seal roll listed at $204.99 (about $2.05 per square foot), and GAF Liberty rolls ran $142.60 for a 200 sq ft base and $137.11 for a 100 sq ft cap, about $2.08 per square foot for two plies. HomeGuide prices installed modified bitumen at $4.00 to $7.50 per square foot.

What temperature do you need to install peel and stick roofing?

MFM’s data sheet requires air and surface temperatures of 55 degrees Fahrenheit or above for Peel and Seal, and GAF lists 45 to 95 degrees for Liberty. Cold matters: MFM measures adhesion to plywood at 51 lb/ft at 75 degrees but 14 lb/ft at 40 degrees. A damp or dusty deck also causes lifting and open seams.

Can you put peel and stick roofing over shingles?

It is not recommended over existing shingles. The data sheet for MFM Peel & Seal requires a clean, smooth, dry surface, and a granular shingle surface lets the membrane bond only at high spots and trap air and moisture beneath. Remove the shingles and prepare the deck first, or choose a system the maker rates for recover.