Subscribe

MATERIALS · July 4, 2026

Types of Metal Roof Panels: Profiles, Metals Compared

Types of metal roof panels by fastener family, profile and metal: standing seam vs corrugated, R-panel, 5V, gauges, and how to choose.

By The Roofing Brief Team. Last reviewed: October 2026.

Types of metal roof panels sort along three axes: the fastener family (hidden-fastener standing seam vs exposed-fastener panels), the panel profile (the shape of the rib or corrugation), and the metal itself (steel, aluminum, copper, or zinc), which is why the old tin roof label is really a misnomer. Pick the fastener family first, then the profile, then the metal. Standing seam is normally rolled in 24 gauge steel or heavier, exposed-fastener panels in 26 to 29 gauge, so a house, a barn and a commercial building each land on a different pairing.

For pricing, see metal roof cost; for single profiles, see corrugated metal roofing and standing seam cost.

What are the two main types of metal roofing?

Metal roofing splits into two fastener families: hidden-fastener systems (standing seam; Western States Metal Roofing lists snap-lock, mechanically seamed and nail-strip versions) and exposed-fastener panels (7/8-inch corrugated, PBR/R-panel and the 7.2 panel in that same catalog). In standing seam, clips or the panel edge hold the roof down and no screw pierces the flat of the panel. In exposed-fastener systems, screws run straight through the panel face into the deck or purlin, with a neoprene washer sealing each hole. One maker spanning both families is Everlast, from the exposed fastener Everlast II to the Everloc snap-lock, as our Everlast metal roofing review details.

This one distinction drives cost, lifespan, and where each system belongs. Hidden-fastener standing seam typically lasts 40 to 70 years and carries wind ratings of 140 to 180 mph because nothing penetrates the water plane. Exposed-fastener panels cost far less and install faster, but the rubber washers under the screws are the wear point: they dry out and back out over a 20 to 40 year life, so the roof needs a fastener check every decade or so.

Fastener family How it holds down Typical life Relative cost Best for
Hidden fastener (standing seam) Clips or seam, no face penetration 40 to 70+ years Highest Homes, high wind, architectural
Exposed fastener (corrugated, R-panel, ribbed) Screws through panel face 20 to 40 years Lowest Barns, shops, budget, agricultural

Standing seam metal roof panel types

Standing seam panels run vertically from ridge to eave with raised seams that lock together over hidden clips. The three common seam types are snap-lock, mechanical-seam, and nail-strip (fastener-flange). They differ in how the seam closes and how much water head they resist, which sets the minimum roof slope each can handle under IRC Section R905.10 and the maker’s tested limits. Our snap lock vs mechanical seam guide compares the first two.

  • Snap-lock: panel edges snap together by hand over a clip. No seaming tool needed. Common on residential roofs; confirm the panel maker’s published minimum slope before ordering.
  • Mechanical seam: a powered or hand seamer folds the seam 90 or 180 degrees. The tightest, most weathertight seam, used on low slopes and on commercial work; the maker’s tested minimum slope governs.
  • Nail-strip (fastener flange): a hidden flange along the panel edge is nailed to the deck, then the next panel snaps over it. Cheaper to install than clipped systems, common on residential, and listed as its own standing seam family in the Western States catalog.

Seam heights run 1 inch to 1.75 inches, and rib spacing is usually 12 to 19 inches. Standing seam is normally rolled in 24 gauge steel or heavier, or in aluminum, because the flat pan shows oil-canning at thinner gauges. Seam height is the first number to compare between quotes: 1-inch snap-lock and 1.75-inch mechanical-seam panels are the two heights behind most quotes on standing seam metal roof cost.

Exposed-fastener panel types and profile names

Exposed-fastener panels are screwed through the face and named by their rib shape. The four you will see quoted most are corrugated, R-panel (PBR), ribbed (Max-Rib and similar), and 5V-crimp. Each has a standard coverage width and gauge range, which is what a supplier means when they list a profile by name.

Profile name Rib shape Typical gauge Common use
7/8″ Corrugated Rounded wave 26 to 29 Agricultural, rustic residential, accent
R-panel / PBR Trapezoidal high rib 26 Commercial, metal buildings, pole barns
Ribbed (Max-Rib, Tuff-Rib) Low trapezoidal rib 26 to 29 Residential, light commercial, sheds
5V-crimp Flat with V-crimps 26 to 29 Historic and coastal residential
7.2 / Mega-Rib Deep symmetrical rib 22 to 24 Long spans, industrial walls and roofs

Corrugated is the oldest profile and reads rustic; R-panel (also called PBR) is the workhorse of metal buildings; 5V-crimp is the classic Florida and coastal look. Gauge matters more than profile for dent resistance: 26 gauge is stiffer than 29 gauge, and lower numbers mean thicker steel. For a low-rib panel that many mills and dealers sell under one name, see our guide to Tuff-Rib metal roofing. The Metal Sales version is reviewed in our guide to the Classic Rib metal roofing panel.

Standing seam vs corrugated: which type should you pick?

If the roof is a house and you want a 40 to 70 year life, buy standing seam in 24 gauge or heavier; if it is a barn, shop or budget job, 26 to 29 gauge corrugated or R-panel wins on price and install speed. Standing seam usually runs at least double the installed price of an exposed-fastener panel of the same metal.

Factor Standing seam Corrugated / exposed fastener
Fasteners Hidden Exposed through face
Typical gauge 22 to 24 26 to 29
Lifespan 40 to 70+ years 20 to 40 years
Maintenance Minimal Refasten washers over time
Relative installed cost Highest Lowest, often 50%+ less
Look Modern, architectural Rustic to industrial

Related: metal vs asphalt shingle roof, commercial metal roofing and insulated metal roof panels.

Metal roof styles beyond panels: shingles, tile, and slate

Beyond vertical panels, metal also comes as stamped products that mimic other roofs: metal shingles, metal tile, metal shake, and metal slate. These are interlocking pieces or modular panels pressed to look like asphalt, clay tile, wood shake, or slate, giving the durability of metal with a traditional profile. They install like a shingle field rather than long panels, so they handle complex rooflines with many valleys and dormers better than long-run standing seam. Our comparison of the types of metal roof panels shows how stamped products stack up on attachment and gauge.

  • Metal shingles: stamped steel or aluminum in a shingle look, often stone-coated. Good for cut-up roofs.
  • Metal tile: profiled to mimic Spanish or barrel clay tile at a fraction of the weight.
  • Metal shake: textured to read as split wood shake, non-combustible.
  • Metal slate: flat stamped panels imitating natural slate without the structural load.

Which metal? Steel, aluminum, copper, and zinc compared

The metal is the third choice, independent of profile. Galvalume-coated steel (55% aluminum-zinc alloy-coated sheet under ASTM A792, a trade name licensed by BIEC International) is the default for cost and strength, aluminum resists coastal salt corrosion, and copper and zinc are premium architectural metals that develop a patina and last a century or more. The same standing seam or corrugated profile can be rolled in any of these, so metal and profile are separate decisions.

Metal Relative cost Lifespan Standout trait
Galvalume steel Low to moderate 40 to 60 years Strength per dollar, most common
Aluminum Moderate 50+ years Will not rust, best near saltwater
Copper High 100+ years Patinas, architectural accents
Zinc High 80 to 100 years Self-healing patina, low expansion

Galvalume steel (40 to 60 years) costs the least of the four. Aluminum (50+ years) will not rust, so it earns its premium within a few miles of saltwater, where cut steel edges can corrode. Copper (100+ years) and zinc (80 to 100 years) are usually reserved for accents, historic work, or high-end custom homes rather than whole roofs.

How to choose a metal roofing type in order

If your roof is Then choose Why
A house you keep 40+ years Standing seam, 24 gauge or heavier 40 to 70 year life, no face penetrations
A barn, shop or outbuilding on a budget 26 to 29 gauge corrugated or R-panel Often 50%+ below standing seam, 20 to 40 year life
Within a few miles of saltwater Aluminum panels Will not rust
Cut up with many valleys and dormers Metal shingles or tile profiles Install like a shingle field

Choose in three steps: fastener family (20 to 40 years vs 40 to 70 years), then profile (sets slope range and look), then metal (sets climate fit and the 40 to 100+ year ceiling). Working the other direction leads to a profile that does not fit the slope or a metal that blows the budget.

  1. Fastener family: pick hidden-fastener standing seam for a long-life house roof, or an exposed-fastener panel for budget, barns, or outbuildings.
  2. Profile and slope: confirm the profile suits your pitch against the maker’s published minimum slope and IRC R905.10; mechanical-seam standing seam is the type made for the lowest slopes.
  3. Metal and climate: default to galvalume steel, switch to aluminum near the coast, and consider copper or zinc only for accents or premium work.

Get itemized per-square numbers before you sign: the metal roof cost guide breaks pricing down by type and region.

Frequently asked questions

What are the different types of metal roofing?

Metal roofing types divide into two fastener families. Hidden-fastener standing seam locks over clips with no screws through the panel face and lasts 40 to 70 years. Exposed-fastener panels, which include corrugated, R-panel or PBR, ribbed, and 5V-crimp, are screwed through the face and last 20 to 40 years. Within those families you also choose a profile and a metal such as steel, aluminum, copper, or zinc.

What is the difference between standing seam and corrugated metal roofing?

Standing seam uses hidden fasteners: clips hold the panels and no screw pierces the water plane, giving a 40 to 70 year life and wind ratings up to 180 mph. Corrugated is an exposed-fastener panel screwed through the face, cheaper and faster to install but with a 20 to 40 year life that depends on the neoprene washers under each screw. Standing seam usually costs at least double corrugated of the same metal.

What are the names of metal roof panels?

Common exposed-fastener panel names include 7/8-inch corrugated, R-panel (also called PBR), ribbed profiles such as Max-Rib and Tuff-Rib, 5V-crimp, and deep-rib panels like 7.2 or Mega-Rib. Standing seam panels are named by seam type: snap-lock, mechanical-seam, and nail-strip or fastener-flange. Each name refers to a specific rib shape, coverage width, and typical gauge.

What gauge is standing seam versus corrugated metal roofing?

Standing seam is normally rolled in 24 gauge steel or heavier, often 22 to 24, because the flat pan shows oil-canning at thinner gauges. Corrugated and other exposed-fastener panels are usually 26 to 29 gauge, meaning thinner metal. Lower gauge numbers mean thicker steel, so a 26 gauge panel is stiffer and more dent-resistant than a 29 gauge panel.

What metals are used for metal roofs?

The four common roofing metals are galvalume-coated steel, aluminum, copper, and zinc. Steel is the least expensive and most common, lasting 40 to 60 years. Aluminum will not rust and suits coastal homes. Copper lasts over 100 years and develops a patina. Zinc lasts 80 to 100 years with a self-healing patina. The same profile can be rolled in any of these metals.

Which type of metal roof is best for a house?

For most houses, a hidden-fastener standing seam roof in galvalume steel offers the best mix of a 40 to 70 year life, high wind resistance, and a clean look, though it costs the most. On a tight budget or an outbuilding, an exposed-fastener ribbed or corrugated panel works. On complex rooflines with many valleys, metal shingles or stone-coated steel install more easily than long standing seam panels.