Subscribe

COST & ESTIMATES · November 20, 2026

Roof Framing Labor Cost Per Square Foot: Rafters vs Trusses

Roof framing labor cost per square foot: $1 to $4 for trusses, $4 to $15 for rafters. Worked 1,500 sq ft gable estimate with BLS wages and crane costs.

Roof Framing Labor Cost Per Square Foot: Rafters vs Trusses

By The Roofing Brief Team | Last reviewed: November 2026

Roof framing labor cost per square foot runs about $1 to $4 for setting prefabricated trusses and $4 to $15 for stick-framing rafters on site, measured per square foot of roof area, according to HomeGuide’s roof framing cost guide (accessed November 2026). With lumber or trusses included, roof framing cost per square foot is $5 to $14 for a truss roof and $7 to $30 for a rafter roof on the same guide, and Fixr (updated January 31, 2025) puts the all-in average at $5.78 to $10.52.

Those are quotes per square foot of roof surface, not of the house footprint. A 1,500 sq ft single-story house with a 6:12 roof and 12 in overhangs carries about 1,860 sq ft of roof, so every per-square-foot figure below says which area it uses, and the worked estimate converts between the two.

Roof framing labor and material cost per square foot, by method

Trusses cost more in material but take a fraction of the labor; rafters flip that split. HomeGuide’s line items show the pattern: truss labor is $1 to $4 per sq ft against $4 to $10 for truss material, while rafter labor reaches $15 per sq ft because every rafter is measured, cut and fitted on the roof.

Wood roof trusses set at even spacing on the framed walls of a single-story house under construction
Prefabricated roof trusses are typically set at 24 inches on center and braced to the wall plates before sheathing goes on. AI-generated illustration.
Line item (per sq ft of roof area) Rafters (stick framed) Trusses (crane set) Source
Labor only $4 to $15 $1 to $4 HomeGuide roof framing guide
Materials only $3 to $15 $4 to $10 HomeGuide roof framing guide
Installed total $7 to $30 $5 to $14 HomeGuide roof framing guide
Installed total, all methods $5.78 to $10.52 (average roof of 1,700 sq ft: $9,828 to $17,882) Fixr, Jan 31, 2025
Truss roof only, installed Not applicable $4.18 to $7.70 (1,000 sq ft roof: $4,180 to $7,700) Fixr truss table, Roofing Brief per-sq-ft division
Labor per truss, set and installed Not applicable $40 to $60 per truss HomeGuide roof truss prices

The ranges are wide because the high end covers hips, valleys, dormers and steep pitches, while the low end is a plain gable over a garage or ranch. A buyer comparing two bids should ask each framer for the roof area they priced and whether ceiling joists, fascia sub-framing and gable-end overhang ladders are inside the number. For the full truss price list by span and type, see our roof truss cost guide.

What framing carpenters earn versus what they bill per hour

The U.S. median wage for carpenters was $29.12 per hour ($60,580 a year) in May 2025, according to the BLS Occupational Outlook Handbook, and the residential building construction median was $60,600. HomeGuide reports framing carpenters billing $30 to $80 per hour to build or set roof framing, so the billed rate runs from roughly 1.0 to 2.75 times the median paid wage once insurance, payroll taxes, tools, travel and profit are added.

State wages move the labor line more than any other single input. The table uses the 2025 BLS wage data that O*NET’s local wage tool publishes for SOC 47-2031 (carpenters), multiplied by the 120 crew-hours in the rafter estimate further down.

Area Median carpenter wage (2025) Index vs U.S. Raw wages for 120 crew-hours Source
United States $29.12/hr 1.00 $3,494 BLS OEWS via O*NET
Illinois $37.98/hr 1.30 $4,558 BLS OEWS via O*NET
California $36.50/hr 1.25 $4,380 BLS OEWS via O*NET
Washington $35.67/hr 1.22 $4,280 BLS OEWS via O*NET
New York $34.77/hr 1.19 $4,172 BLS OEWS via O*NET
Colorado $30.21/hr 1.04 $3,625 BLS OEWS via O*NET
Florida $23.98/hr 0.82 $2,878 BLS OEWS via O*NET
Texas $23.51/hr 0.81 $2,821 BLS OEWS via O*NET

Read the index as a rough multiplier on the labor share of a bid, not on the whole bid. A California rafter roof priced at the national $4 to $15 per sq ft labor band lands near $5.00 to $18.75 at the 1.25 index, while lumber and trusses follow regional supply prices rather than local wages. The 90th percentile carpenter wage nationally was $48.03 per hour, which is the territory of lead framers who cut hips and valleys.

Worked estimate: framing a 1,500 sq ft gable roof both ways

This Roofing Brief estimate prices one simple house two ways, with every input stated so you can swap in your own. The house is 30 ft by 50 ft (1,500 sq ft footprint), single story, with a 6:12 gable roof and 12 in overhangs at eaves and rakes.

Input Value How it was derived
Plan area with overhangs 32 ft x 52 ft = 1,664 sq ft Footprint plus 1 ft each side
6:12 slope factor 1.118 Square root of (1 + (6/12) squared)
Roof surface area 1,860 sq ft (18.6 squares) 1,664 x 1.118
Common rafter length 17.9 ft, cut from 18 ft stock 16 ft horizontal (15 ft run + 1 ft tail) x 1.118
Rafter size 2×8 Douglas fir-larch No. 2 at 16 in on center IRC Tables R802.4.1(1) and (3): 18 ft 5 in allowable span at 20 psf roof live load; 15 ft 4 in at 30 psf ground snow, both over the 15 ft run
Rafter count 78 (39 per side) 50 ft x 12 / 16 in = 37.5 spaces, rounded to 38, plus 1
Truss count 26 trusses, 30 ft span, 24 in on center 50 ft / 2 ft = 25 spaces plus 1 (2 are gable-end trusses)

Rafter sizes come from the span tables in 2021 IRC Chapter 8; our gable roof framing guide reproduces the 2×6 to 2×12 rows. At a 50 psf ground snow load the 2×8 drops to a 12 ft 6 in allowable span, so the same house would need 2×10 rafters (15 ft 3 in), which raises the board-foot count by 25 percent.

Lumber take-off for the rafter roof

Member Quantity Board feet Note
2×8 x 18 ft common rafters 78 1,872 (24 each) 2 x 8 x 18 / 12
2×10 ridge board, 52 ft run 3 pieces 87 Ridge at least as deep as the 2×8 plumb cut (about 8.1 in at 6:12), per IRC R802.3
1×4 x 8 ft collar ties at 4 ft on center 13 35 Upper-third ties per IRC R802.4.6
2×6 x 16 ft ceiling joists / rafter ties 78 1,248 (16 each) Assumed size, lapped over a center bearing wall; confirm in IRC Table R802.5.1(1)
Total 3,242 bf About 3.24 thousand board feet (MBF)

Gordian’s RSMeans framing lumber cost index stood at $1,004.40 per MBF in Q4 2026 (published October 13, 2026), up about 10 percent from Q3’s $915.88. At that index, 3.24 MBF is $3,256, or $3,582 with 10 percent waste. Retail yard prices for single 18 ft sticks can run higher than a contractor index, so treat this as a floor.

Labor hours and the two totals

HomeGuide says a truss roof is usually set within a day, while a rafter roof takes several days to a week or more. The estimate turns that into hours with a stated assumption: a three-carpenter crew working 4 to 6 eight-hour days on the rafters and ceiling joists (96 to 144 crew-hours), and 1 to 1.5 days on the trusses (24 to 36 crew-hours). For comparison, HowMuch.net, citing the 2019 Craftsman Estimator costbook, budgets 40 labor hours for a crane-set 1,500 sq ft roof.

Line item Rafter roof Truss roof Source or arithmetic
Framing material $3,582 (3.24 MBF + 10%) $3,120 to $8,580 (26 x $120 to $330) Gordian Q4 2026; HomeGuide 30 ft wood truss price
Labor $2,880 to $11,520 (96 to 144 hr x $30 to $80) $1,040 to $1,560 (26 x $40 to $60) HomeGuide billed rates
Crane, 1 day $0 (lumber is hand carried) $200 to $700 HomeGuide; BigRentz (April 27, 2026) lists small cranes at $300 to $600 per day
Permit $150 to $500 $150 to $500 HomeGuide
Total $6,612 to $15,602 $4,510 to $11,340 Sum of rows
Per sq ft of roof (1,860) $3.55 to $8.39 $2.42 to $6.10 Total / 1,860
Per sq ft of footprint (1,500) $4.41 to $10.40 $3.01 to $7.56 Total / 1,500
Labor only, per sq ft of roof $1.55 to $6.19 $0.56 to $0.84 ($0.67 to $1.22 with crane) Labor / 1,860

Two things fall out of the arithmetic. First, the bottom-up rafter labor of $1.55 to $6.19 per sq ft sits at or below the bottom half of HomeGuide’s $4 to $15 band, which means a simple gable should be bid near the low end and a $12 per sq ft labor quote needs hips, valleys or a steep pitch to justify it. Second, the truss roof includes its ceiling framing in the bottom chord and clears the 30 ft span without the center bearing wall the lapped 2×6 joists need, which is a cost the rafter column does not show.

How pitch changes the cost per square foot of your house

Pitch raises the roof area that framers price, so the same footprint costs more at 10:12 than at 4:12 before any steep-roof labor premium. The table applies HomeGuide’s labor bands to a 1,500 sq ft footprint with 12 in overhangs (1,664 sq ft of plan area).

Pitch Slope factor Roof area Roof area per footprint sq ft Truss labor ($1 to $4) Rafter labor ($4 to $15)
4:12 1.054 1,754 sq ft 1.17 $1,754 to $7,016 $7,016 to $26,310
6:12 1.118 1,860 sq ft 1.24 $1,860 to $7,442 $7,442 to $27,906
8:12 1.202 2,000 sq ft 1.33 $2,000 to $8,000 $8,000 to $29,998
10:12 1.302 2,166 sq ft 1.44 $2,166 to $8,664 $8,664 to $32,491
12:12 1.414 2,353 sq ft 1.57 $2,353 to $9,413 $9,413 to $35,299

Slope factor is the square root of 1 plus (rise/12) squared; labor columns are Roofing Brief arithmetic on HomeGuide’s ranges. If you are weighing a steeper pitch on an existing house, our cost of raising a roof pitch breakdown prices the tear-off and overframe lines that this table leaves out.

Hip roofs, additions, porch roofs and re-framing

A hip roof adds four hip rafters plus a set of jack rafters on each end. At 6:12 the hip rafter is 1.5 times its common run (the square root of 36 + 288, divided by 12), so on the 30 ft wide house each hip rafter is about 22.5 ft before the tail, which pushes past 20 ft stock into 24 ft lumber or an LVL. Every jack rafter has a compound cut, which is why HomeGuide calls mansard and multi-plane roofs the most expensive to frame. Our hip roof guide compares hip and gable on wind and cost, and roof valley framing covers the valley and jack math.

Stick-framed hip roof with jack rafters nailed to a long hip rafter on a new house
On a hip roof, each jack rafter needs a compound cut where it meets the hip rafter, which adds framing labor compared with a gable. AI-generated illustration.

Small additions and porch roofs usually get stick-framed, because a 10 to 14 ft lean-to or gable does not justify a crane day and must tie into existing framing. HomeGuide’s 12 to 14 ft truss prices of $60 to $150 each still make trusses cheaper in material when a truck can reach the wall. Covered-deck pricing, which adds posts, beams and footings, is in our cost to add a roof over a deck guide.

Re-framing after a fire or rot adds removal before any new framing. HomeGuide lists removal at $30 to $50 per truss or $0.60 to $1.00 per linear foot of rafter, plus $300 to $500 per week for a dumpster, and Fixr puts demolition of roof framing at $0.66 to $1.20 per sq ft, before shingles and underlayment come off. When only a few members are cracked, cut or charred, an engineered repair detail may replace tear-out; our roof truss repair guide covers sistering, gussets and when replacement is cheaper.

Permits, engineering and truss drawings

A framing permit is required when roof framing is built or replaced, and HomeGuide prices a roofing permit at $150 to $500. Trusses come with their own paperwork: under IRC Section R802.10.1, truss design drawings “shall be provided to the Building Official and approved prior to installation,” and R802.10.2 requires metal-plated wood trusses to be designed and manufactured to ANSI/TPI 1, as summarized in STRUCTURE magazine’s guide to residential truss code requirements.

Rafter roofs avoid the truss submittal but must fit the IRC span tables, rafter ties and uplift connections, or carry an engineer’s design. HomeGuide lists $150 to $600 for a structural engineer to inspect roof framing, $100 to $250 per hour for an architect to design a new roof plan, and $150 to $2,500 to alter existing blueprints. A structural ridge beam, needed when rafter ties are omitted for a vaulted ceiling, is a separate engineered member covered in ridge beam vs ridge board.

Rafters or trusses: which costs less for your roof?

If your project is Then price it as Why
A new gable or hip house under 40 ft wide with a truck-accessible lot Trusses Labor drops to $1 to $4 per sq ft (HomeGuide) and the bottom chord frames the ceiling
A roof where you want attic living space or a vaulted ceiling Rafters, or attic or scissor trusses Standard W-web trusses leave little usable attic
A lot with no room for a truck and crane Rafters HomeGuide notes trusses need freight delivery and a crane, $200 to $700 per day
A 50 psf ground snow area Engineered trusses, or upsize rafters 2×8 at 16 in drops to a 12 ft 6 in span in IRC Table R802.4.1(5)
A small addition or porch tying into an old roof Rafters Matches existing framing without waiting 2 to 6 weeks for truss delivery (HomeGuide)
Fire, rot or cut members in a few bays Engineered repair first, then partial re-frame Removal alone is $30 to $50 per truss before new framing

How to estimate roof framing labor for your own roof

  1. Measure the footprint and add the overhang on every side (a 30 x 50 ft house with 12 in overhangs becomes 32 x 52 ft).
  2. Multiply that plan area by the slope factor for your pitch (1.118 at 6:12, 1.302 at 10:12) to get roof area in square feet.
  3. Count members: span length x 12 divided by spacing in inches, plus 1, per side for rafters (16 in or 24 in on center) or once for trusses (usually 24 in on center).
  4. Size rafters from IRC Table R802.4.1 for your snow or live load, then convert to board feet: thickness x width x length / 12.
  5. Estimate crew-hours from days on site (3 carpenters x 8 hours x days), and multiply by a billed rate of $30 to $80 per hour (HomeGuide).
  6. Divide labor by roof area and check it against the $1 to $4 (truss) or $4 to $15 (rafter) labor band; a figure above the band should come with hips, valleys or steep-pitch reasons.
  7. Add the crane day ($200 to $700), the permit ($150 to $500) and any engineering before comparing bids.

Roof framing is the structure under the decking and covering; shingle installation labor is a separate trade line priced per square, covered in roofing labor cost per square. National covering prices, including $5 to $8 per sq ft installed for architectural asphalt, are in the 2026 Roofing Cost Report.

Frequently asked questions

How much do framers charge per square foot for a roof?

Framers charge about $1 to $4 per square foot of roof area to set trusses and $4 to $15 to stick-frame rafters, per HomeGuide’s roof framing cost guide. On a 1,860 sq ft roof that is $1,860 to $7,440 for trusses and $7,440 to $27,900 for rafters, labor only. Hips, valleys, dormers and pitches above 8:12 push quotes toward the top of each range.

How much should I charge to frame a roof?

Build the price from hours, not a flat rate: crew-hours times your billed rate, plus crane, permit and markup. A three-person crew spending 4 to 6 days on a 1,860 sq ft rafter roof logs 96 to 144 hours, which is $2,880 to $11,520 at the $30 to $80 per hour range HomeGuide reports. The BLS median carpenter wage was $29.12 per hour in May 2025.

How do you calculate framing labor cost?

Multiply roof area by a per-square-foot labor rate, or crew-hours by an hourly rate, and use the second to check the first. Roof area is plan area with overhangs times the slope factor (1.118 at 6:12). For a 30 x 50 ft house that is 1,860 sq ft; at $1 to $4 per sq ft for truss setting, labor is $1,860 to $7,440.

Is roof framing priced per square foot of house or of roof?

Most cost guides, including HomeGuide and Fixr, price roof framing per square foot of roof area. Roof area is larger than the footprint: 1.17 times at 4:12 and 1.57 times at 12:12 with 12 in overhangs on a 1,500 sq ft house. Ask every bidder which area they used before comparing per-square-foot numbers.