By The Roofing Brief Team. Last reviewed: October 2026.
How much it costs to raise a roof on a house: $15,000 to $125,000, with an average of about $50,000, according to This Old House (updated March 31, 2026). HomeAdvisor puts the typical project at $40,000 to $80,000, around $60,000. The spread is wide because “raise a roof” covers three different projects: lifting the whole roof for more headroom, vaulting a single ceiling, or gutting and rebuilding the roof structure to add usable space. Your frame type (truss or stick) sets both the price and what you can build, and lift height and a change of pitch move the bill from there.
How much does it cost to raise a roof on a house?
Most roof raises run $15,000 to $125,000, averaging about $50,000, per This Old House (March 2026). HomeAdvisor reports $40,000 to $80,000 with most homeowners near $60,000, and HomeGuide (January 2024) reports $30,000 to $70,000 on average, reaching $125,000 or more. This Old House notes that a reliable per-square-foot figure is hard to give because so many variables are involved. A modest ceiling lift over one room sits at the low end. Raising the full roofline of a whole house to gain a habitable attic level sits at the top.
Scope and structure move the number far more than roofing material: the new roof covering is only $8,500 to $14,300 of the total, per This Old House. The table lists the published ranges we could verify, with the source for each.
| Project or benchmark | Published cost | Source |
|---|---|---|
| Raise a roof, all scopes | $15,000 to $125,000; about $50,000 average | This Old House, Mar 31, 2026 |
| Raise a roof, typical range | $40,000 to $80,000; about $60,000 average; low $15,000, high $130,000 | HomeAdvisor |
| Raise a roof, typical range | $30,000 to $70,000; up to $125,000 or more | HomeGuide, Jan 31, 2024 |
| Raise a flat roof | $15,000 to $50,000 | This Old House, Mar 31, 2026 |
| Finish an attic | $50 to $150 per sq ft, or $15,000 to $75,000 | HomeGuide, Jan 31, 2024 |
| Second-story addition, including the new roof | $200 to $500 per sq ft, or $200,000 to $750,000 or more | HomeGuide, Jan 31, 2024 |
These figures assume a standard single-family home. A Cape Cod, bungalow, or Victorian with complex framing tends to land toward the top of the range, because This Old House notes that multiple valleys and pitch changes require more structural support.
What drives the cost of raising a roof
Five factors move the price more than anything else: frame type, home size, structural requirements, permits, and add-on work like chimney or HVAC relocation. This Old House names ranch, flat-roof, and mid-century modern houses as the least expensive to raise and Victorian and Cape Cod homes as costlier because of their complex rooflines. A stick-framed home where you want a vaulted, open ceiling is the most expensive because it forces a full teardown and rebuild.
- Frame type. Trussed roofs can often be raised or swapped without demolishing the whole assembly. Stick-framed roofs usually need full removal and rebuild.
- Square footage. Larger homes cost more because more material and labor are needed, so a 2,000 sq ft footprint costs far more than a single room.
- Structural engineering. A licensed engineer must design new load paths, walls, and headers. This Old House puts an initial structural engineer consultation at about $500 and an architect’s design at about $3,000.
- Permits and inspections. This Old House puts building, plumbing, and wiring permits at $400 to $2,000, and the work triggers multiple inspections.
- Add-on work. Raising the roof next to a chimney adds $500 to $6,000, per This Old House, and the chimney may need to be rebuilt to the new height. Rerouting HVAC, electrical, and plumbing that ran through the old attic is billed by licensed trades, which This Old House puts at $50 to $150 per hour.
Line-item breakdown of a roof raise
A roof raise is a stack of separate trades, and the table lists the published unit cost for each line. HomeGuide prices the new roof, wall, and ceiling installation at $6 to $15 per sq ft and new trusses at $5 to $14 per sq ft; shoring and the final framing quantities depend on the engineer’s design and are bid per project.
| Line item | Published cost | Source |
|---|---|---|
| Structural engineer consultation | About $500 | This Old House |
| Architect design of the new roof | About $3,000 | This Old House |
| Permits (building, plumbing, wiring) | $400 to $2,000 | This Old House |
| Tear-off and cleanup labor | $30 to $50 per hour, plus haul-away | This Old House |
| New roof covering | $8,500 to $14,300 | This Old House |
| Roofing labor | $1.50 to $3 per sq ft, plus materials | This Old House; HomeAdvisor |
| Chimney work next to the raised section | $500 to $6,000 extra | This Old House |
| Plumbers and electricians | $50 to $150 per hour | This Old House |
| New insulation | $1.00 to $4.50 per sq ft installed | HomeGuide, Jan 2024 |
| General contractor oversight | 10% to 20% of the total | This Old House; HomeAdvisor |
| Roof, wall, and ceiling installation | $6 to $15 per sq ft | HomeGuide, Jan 2024 |
| New roof trusses | $5 to $14 per sq ft | HomeGuide, Jan 2024 |
| Drywall ceiling replacement | $2 to $4 per sq ft | HomeGuide, Jan 2024 |
| Electrical rewiring | $5 to $17 per sq ft | HomeGuide, Jan 2024 |
| Relocate an AC unit | $1,000 to $2,000 | HomeGuide, Jan 2024 |
| HVAC ductwork replacement | $25 to $55 per linear ft | HomeGuide, Jan 2024 |
| Rebuild chimney from the roofline | $1,000 to $3,500 | HomeGuide, Jan 2024 |
The new roof covering, $8,500 to $14,300 per This Old House, is often quoted separately because it is essentially a full reroof. To price that piece on its own, see the breakdown of the cost to reroof a house. The framing cost depends heavily on roof truss cost and type, which changes with span and truss design.
How much does it cost to raise a roof 2 feet?
Raising a roof 2 feet costs less than a full-story lift, but not proportionally less. Lift height mostly changes two parts of the job: new wall framing and the siding and exterior infill that close the gap. On a 30 ft by 50 ft ranch (160 ft of perimeter), every foot of lift adds 160 sq ft of exterior wall to frame, sheathe, insulate, and side, so a 2-foot raise adds about 320 sq ft and a 6-foot raise about 960 sq ft. Engineering, permits, tear-off, shoring, the new roof covering, and much of the interior work cost about the same whether the roof goes up 2 feet or 6.
Before you settle on a height, decide what the raise has to achieve. If the goal is habitable attic space, many jurisdictions apply IRC Section R305.1: habitable rooms need a ceiling height of at least 7 feet, and in a room with a sloped ceiling at least 50 percent of the required floor area must reach 7 feet, with no required floor area under 5 feet, as summarized in the City of Boise IRC R305 ceiling height handout. A 2-foot lift that leaves the attic short of those heights adds storage headroom but may not create a legal bedroom. Local amendments vary, so confirm the target height with your engineer and building department before the plans are drawn.
Because most of the line items stay fixed, a small lift tends to cost more per foot of height gained than a large one. On This Old House’s figures, the engineer ($500), architect ($3,000), permits ($400 to $2,000), and new roof covering ($8,500 to $14,300) add up to $12,400 to $19,800 whether the roof rises 2 feet or 6. If you are paying that anyway, price a second option at the height that would make the space habitable and compare the two bids.
Which project fits your goal: decision table
| If your goal is… | Best project | Published cost |
|---|---|---|
| A taller-looking room with no structural work | Tray ceiling | $3 to $7 per sq ft (HomeGuide) |
| An open, peaked ceiling in one room of a stick-framed house | Vaulted ceiling | $40 to $70 per sq ft (HomeGuide) |
| More headroom upstairs in a Cape Cod | Price a shed or gable dormer before a full raise | Dormer $90 to $150 per sq ft, or $3,000 to $25,000 (HomeGuide) |
| A legal attic bedroom | Raise high enough that half the required floor area reaches 7 ft (IRC R305.1), then finish the attic | Raise $15,000 to $125,000 (This Old House) plus attic finish $50 to $150 per sq ft (HomeGuide) |
| Higher ceilings on a flat-roofed house | Raise the flat roof | $15,000 to $50,000 (This Old House) |
| A full new floor of rooms | Second-story addition | $200 to $500 per sq ft (HomeGuide) |
Trussed roof vs stick-framed roof: cost and what you can build
Frame type decides both the price and the ceiling shape you can end up with. A trussed roof is cheaper to raise, because HomeGuide notes trusses can be raised, repaired, or replaced without tearing off the entire roof, but it locks you into a flat ceiling. A stick-framed roof costs more because it must be torn down and rebuilt, but that rebuild is the only path to a true vaulted or cathedral ceiling. This tradeoff, not the roofing material, is the real fork in the decision. Flat roofs are a separate job, covered in our guide to flat roof to pitched roof conversion.
| Factor | Trussed roof | Stick-framed roof |
|---|---|---|
| Relative cost to raise | Lower | Higher |
| Method | Raise or replace trusses, often without full demolition | Full teardown and rebuild |
| Vaulted ceiling possible? | No, webbing blocks open space | Yes |
| Best when you want | More headroom at lower cost | Open, vaulted, or cathedral ceiling |
Trusses carry load through internal webs, so you cannot simply remove them to open the ceiling: IRC R802.10.4 bars cutting, notching, drilling, splicing, or otherwise altering truss members without approval from a registered design professional. Converting to an open vault means switching to rafters with structural ridge and collar support, which is a stick-frame job. For how those members are laid out, see gable roof framing. Our roof trusses guide explains when a truss or a rafter frame fits the job.
How much does it cost to raise a roof’s pitch?
Changing a roof’s pitch replaces the roof framing and the entire roof covering, so This Old House notes it is “just as expensive as roof-raising.” A steeper pitch also adds roof surface: going from 4/12 to 8/12 adds about 14 percent more roof to cover (1.202 divided by 1.054). For the methods, a worked example, and the code rules, see our guide to the cost of raising a roof pitch.
Raise the roof vs vault a ceiling vs add a second story
These three projects get quoted under the same search but deliver very different results. Vaulting a ceiling, at $40 to $70 per sq ft per HomeGuide, changes one room’s shape with no new floor area. Raising the roof lifts the roofline for headroom across the house. Adding a second story builds new rooms and is by far the most expensive. Matching the project to your goal prevents overpaying for scope you do not need.
| Project | Published cost | New floor area? | Timeline |
|---|---|---|---|
| Vault or tray ceiling in one room | Vaulted $40 to $70 per sq ft; tray $3 to $7 per sq ft (HomeGuide) | No | Shorter than a full raise |
| Raise the roof | $15,000 to $125,000 (This Old House) | Sometimes (habitable attic) | Typically 4 to 6 weeks (This Old House) |
| Add a second story | $200,000 to $750,000 or more (HomeGuide) | Yes, full floor | Longest of the three |
Raising a roof is generally cheaper and faster than a second-story addition, which HomeGuide prices at $200 to $500 per square foot including the new roof. If the goal is a taller, more open room rather than more square footage, a vault or a straight roof raise is the far cheaper answer.
Do you need a permit to raise a roof?
Yes. Raising a roof is a structural modification, so it requires a building permit and stamped engineering in nearly every jurisdiction. This Old House puts permit fees at $400 to $2,000, and the work triggers multiple inspections, including framing and final structural sign-off. Unpermitted structural work can complicate insurance claims and resale, and a building department may require it to be opened up or redone.
Because the project alters the load path, most building departments require plans from a licensed structural engineer or architect. HomeGuide puts architects at $100 to $250 per hour or 10% to 20% of the project, and structural engineers at $100 to $220 per hour, often folded into the architect’s fee. Plan review can add weeks before demolition starts.
How long does raising a roof take?
A roof raise typically takes four to six weeks, depending on the roof’s size and complexity, according to This Old House, which also warns that owners may need to be out of the home for more than a month. The permit and design phase before any work begins adds time on top of that, so build it into the schedule from day one.
Weather is the main schedule risk across a 4 to 6 week build, since the roof comes off and the interior sits exposed under temporary protection. Contractors sequence tear-off, framing, and dry-in tightly to limit that window, and HomeGuide notes a trussed roof usually goes faster than a stick-framed rebuild.
Is raising a roof worth it?
Raising a roof can pay back when it adds usable, code-height living space or corrects a cramped floor plan that hurts resale, but it rarely returns 100% of its cost at sale. This Old House puts the return on raising a roof at 50% to 54%, meaning owners recoup about half the cost when they sell; the exact figure varies by market, home value, and how the new space is finished.
The strongest case is a home where a low or chopped-up roofline blocks an otherwise valuable attic or main-floor space. For how roof-related upgrades track against resale value, see The Roofing Brief’s roof replacement ROI and resale value data. To understand the underlying structure before you plan a raise, the Learn About Roofing hub covers how roofs are framed and loaded.
Frequently asked questions
How much does it cost to raise a roof on a house?
Raising a roof on a house costs $15,000 to $125,000, with an average of about $50,000, according to This Old House (March 2026); HomeAdvisor puts most projects at $40,000 to $80,000. A single-room ceiling raise sits at the low end, while lifting the full roofline of a whole house to create habitable space sits at the top. Frame type and home size drive the number more than roofing material.
Is it cheaper to raise a roof or add a second story?
Raising a roof is almost always cheaper than adding a second story. A roof raise runs $15,000 to $125,000 according to This Old House, while HomeGuide prices a second-story addition at $200 to $500 per square foot, or $200,000 to $750,000 or more including the new roof. A roof raise typically takes four to six weeks; a full second story takes considerably longer.
Can you raise the roof on a trussed house?
Yes, a trussed roof can be raised, and it is often cheaper than a stick-framed roof because the trusses can be raised or replaced without demolishing the whole assembly. The limit is shape: IRC R802.10.4 bars altering truss members without a registered design professional’s approval, so trusses cannot simply be opened into a vaulted ceiling. For a vault, the roof is rebuilt with rafters.
Do you need a permit to raise a roof?
Yes. Raising a roof is a structural change that requires a building permit and, in most cases, stamped plans from a licensed structural engineer. This Old House puts permit fees at $400 to $2,000, and the work triggers framing and final inspections. Requirements vary by jurisdiction, and unpermitted structural work can complicate insurance claims and resale.
How long does it take to raise a roof?
A roof raise typically takes four to six weeks, depending on the roof’s size and complexity, according to This Old House. The design and permit phase beforehand adds time on top of that. Weather delays are the main schedule risk once the roof is off.
How much does it cost to raise a ceiling to a vault?
HomeGuide prices a vaulted ceiling at $40 to $70 per sq ft installed, so a 15 ft by 20 ft room (300 sq ft) runs about $12,000 to $21,000; a tray ceiling is $3 to $7 per sq ft. Vaulting requires a stick-framed roof or a conversion to rafters, since a trussed roof cannot be opened up, and it adds height but no new floor area.