Subscribe

ADJACENCIES · August 17, 2026

What Size Gutters Do I Need? Sizing 5-Inch vs 6-Inch by Roof Area and Rainfall

What size gutters do I need? 5-inch K-style for most runs; 6-inch when a run outgrows its 2x3 downspouts at your rainfall. Gutter sizes and SMACNA math.

What size gutters do I need? Most single-family homes need 5-inch K-style gutters, rated by This Old House at up to 5,520 square feet of drainage area, and you move to 6-inch K-style (about 7,960 square feet) when a single run drains a large or steep roof section or your rain falls hard. The size is not a guess. It comes from three numbers: the roof area draining into each gutter, your roof pitch factor, and your local 5-minute rainfall intensity. Get those, and the gutter width and downspout count fall out of the SMACNA method below.

What size gutters do I need for a typical house?

For most one and two-story homes with simple rooflines, 5-inch K-style gutters paired with 2×3 inch downspouts handle the load. You move up to 6-inch gutters with 3×4 inch downspouts when one run collects a large, steep or valley-fed roof section, or when your region sees short, intense downpours. By This Old House’s figures (updated April 20, 2026), a 6-inch K-style carries about 44 percent more than a 5-inch (7,960 vs 5,520 square feet), and a plain 3×4 downspout has 12.00 square inches of cross-section against 6.00 for a 2×3, so it drains twice the roof area.

The mistake is sizing by house size instead of by drainage section. A gutter only ever handles the roof that drains into it, not the whole roof. A modest house with one long 6:12 plane feeding a single downspout can overwhelm a 5-inch gutter, while a large house split into four short runs may size fine at 5 inches. Size each run on its own.

Standard gutter and downspout sizes

Residential gutters and eavestroughs are sold by the width across the top opening. Lowe’s gutter buying guide lists 4, 5 and 6 inch sizes as the common retail widths, and seamless installers also run 7 and 8 inch K-style for large or commercial roofs. Downspout sizes follow the dimensions in Berger’s SMACNA-based Proper Gutter and Downspout Sizing appendix (Table 1-3).

Size Profile Typical pairing Capacity or area Source
5 in gutter K-style 2×3 downspout Up to 5,520 sq ft drainage area This Old House, Apr 2026
6 in gutter K-style 3×4 downspout About 7,960 sq ft This Old House, Apr 2026
5 in gutter Half-round 3 in round downspout Up to 2,500 sq ft This Old House, Apr 2026
6 in gutter Half-round 4 in round downspout Up to 3,840 sq ft This Old House, Apr 2026
2×3 in downspout Plain rectangular 5 in K-style 6.00 sq in Berger Table 1-3
3×4 in downspout Plain rectangular 6 in K-style 12.00 sq in Berger Table 1-3
3 in downspout Plain round 5 in half-round 7.07 sq in Berger Table 1-3
4 in downspout Plain round 6 in half-round 12.57 sq in Berger Table 1-3

This Old House does not state the rainfall rate behind its capacity figures, so use them to compare sizes, not as your design number; the SMACNA method below sizes to your own rainfall.

How to calculate the gutter size you need

Calculate gutter size in five steps: measure the roof area draining to each gutter, adjust it for pitch, look up your rainfall intensity, convert to required downspout area, then pick the gutter width and downspout count that meet it. This is the SMACNA method from the Architectural Sheet Metal Manual (SMACNA also publishes a downspout and gutter sizing calculator), condensed for a homeowner.

  1. Split the roof into drainage sections. Each slope or plane that sheds into one continuous gutter run is one section; Berger’s SMACNA appendix caps a gutter at 50 ft between ends or expansion joints, so a longer eave becomes two sections.
  2. Measure the footprint area of each section. Multiply the horizontal length by the horizontal depth the plane covers, in square feet: a 40 ft eave under a plane that runs 15 ft back is 600 sq ft. Use the plan footprint, not the sloped surface, and add dormers and additions that drain the same way.
  3. Apply the pitch factor. Multiply the footprint area by the SMACNA multiplier for your slope from the table below (1.00 up to 3:12, 1.30 at 12:12). Berger notes that using the true sloped area “often leads to oversizing”, which is why the factor is smaller than the slope factor.
  4. Look up your rainfall intensity. Find your local 5-minute rainfall in inches per hour from the NOAA Atlas 14 Precipitation Frequency Data Server. Berger’s worked example uses the 10-year, 5-minute storm (Table 1-2, column A; column B gives 100-year values), and that table lists 6.8 in/hr for Chicago and 8.2 in/hr for Houston.
  5. Convert to downspout area. Divide the design area by the roof area one square inch of downspout drains at your intensity (about 1,200 divided by your in/hr, per Berger Table 1-2), then choose downspouts whose cross-section adds up to at least that.

To sanity check flow, Berger states that 96.15 square feet of roof at 1 inch per hour produces 1 gallon per minute, so effective area x rainfall in inches per hour x 0.0104 = gallons per minute the gutter must carry. A 1,100 square foot section at 5 inches per hour sends about 57 gallons per minute to the gutter; by the SMACNA ratio it needs 1,100 / 240 = 4.6 square inches of downspout, which one plain 2×3 (6.00) covers on capacity.

Gutter size and downspout count by roof area and rainfall

The first table gives the design roof area one downspout drains at each rainfall intensity, from Berger’s Table 1-2 ratio (roof area per square inch of downspout, about 1,200 divided by intensity) times the Table 1-3 cross-sections. Read your intensity off NOAA, then compare each run’s pitch-adjusted area to the column for your downspout.

5-minute rainfall intensity Roof area per sq in of downspout One 2×3 (6.00 sq in) One 3 in round (7.07 sq in) One 3×4 (12.00 sq in) One 4 in round (12.57 sq in)
2 in/hr 600 sq ft 3,600 sq ft 4,242 sq ft 7,200 sq ft 7,542 sq ft
4 in/hr 300 sq ft 1,800 sq ft 2,121 sq ft 3,600 sq ft 3,771 sq ft
6 in/hr 200 sq ft 1,200 sq ft 1,414 sq ft 2,400 sq ft 2,514 sq ft
8 in/hr 150 sq ft 900 sq ft 1,061 sq ft 1,800 sq ft 1,886 sq ft
10 in/hr 120 sq ft 720 sq ft 848 sq ft 1,440 sq ft 1,508 sq ft

The second table applies Berger’s published 10-year, 5-minute values for named cities (records through 1978, so check NOAA Atlas 14 for current numbers) to the two standard residential downspouts.

City (Berger Table 1-2, column A) Intensity Sq ft per sq in One 2×3 drains One 3×4 drains
Seattle, WA / Portland, OR 2.1 in/hr 570 3,420 sq ft 6,840 sq ft
Los Angeles, CA 4.9 in/hr 250 1,500 sq ft 3,000 sq ft
Boston, MA 5.3 in/hr 230 1,380 sq ft 2,760 sq ft
Phoenix, AZ 5.6 in/hr 220 1,320 sq ft 2,640 sq ft
Denver, CO 5.7 in/hr 210 1,260 sq ft 2,520 sq ft
Chicago, IL / New York City / Philadelphia 6.7 to 6.8 in/hr 180 1,080 sq ft 2,160 sq ft
Atlanta, GA / Dallas, TX / Miami, FL 7.3 to 7.7 in/hr 160 960 sq ft 1,920 sq ft
Houston, TX 8.2 in/hr 150 900 sq ft 1,800 sq ft
Tampa, FL / New Orleans, LA 8.3 in/hr 140 840 sq ft 1,680 sq ft
If the run’s pitch-adjusted area is Choose Why
Under one 2×3’s area for your city, run under 50 ft 5 in K-style, one 2×3 Downspout area meets the SMACNA ratio
Between one and two 2×3 areas 5 in K-style with two 2×3, or 6 in K-style with one 3×4 Two 2×3 (12.00 sq in) equal one 3×4
Over two 2×3 areas, or valleys dump into the run 6 in K-style with 3×4 outlets 3×4 drains twice a 2×3; 6 in carries about 44% more (This Old House)
Eave longer than 50 ft Split into two runs with an outlet or expansion joint Berger/SMACNA 50 ft limit between ends or expansion joints
Porch, shed or canopy roof Mini gutter with a small outlet SMACNA reserves downspouts under 7.00 sq in for small areas

The pattern to read from these tables: rainfall intensity matters as much as roof area. A section one 2×3 drains in Seattle (3,420 sq ft) needs a 3×4 or two 2×3 outlets in Houston above 900 sq ft. Downspout count, not gutter width alone, is usually what protects a large or steep roof.

Why roof pitch changes the gutter size you need

Roof pitch changes the effective drainage area because a steeper slope catches more wind-driven rain and delivers it faster, so its gutter behaves as if it were serving a larger roof. SMACNA accounts for this with a pitch factor that multiplies the plan area. A 12-in-12 roof adds 30 percent to the area a gutter must handle compared to a flat roof of the same footprint.

Roof pitch Pitch factor (multiply footprint area)
Flat to 3-in-12 1.00
4-in-12 to 5-in-12 1.05
6-in-12 to 8-in-12 1.10
9-in-12 to 11-in-12 1.20
12-in-12 and steeper 1.30

These are the values in Berger’s Table 1-1 (Design Areas for Pitched Roofs), and This Old House’s April 2026 guide prints the same five factors. Two houses with the same footprint but different pitches need different sizing: an 800 sq ft footprint is 800 sq ft of design area at 3:12 but 1,040 sq ft at 12:12.

How many downspouts do you need?

You need enough downspout cross-section that the total covers the run’s pitch-adjusted area at your rainfall, per the SMACNA ratio above, and enough outlets that no gutter section exceeds 50 feet between ends or expansion joints. The old shortcut of one square inch of downspout per 100 square feet of roof matches the SMACNA ratio only at about 12 inches per hour, so it oversizes for most of the country. Our guide to downspout placement and sizing works the rule through for each run.

  • Cross-section sets the capacity. A plain 2×3 downspout is 6.00 square inches and a 3×4 is 12.00, per Berger Table 1-3, so the larger one clears double the roof area on the same gutter.
  • Length sets the minimum count. Berger’s SMACNA appendix limits a gutter to 50 ft between ends or expansion joints, so a 70 ft eave needs at least two sections and two outlets.
  • Add outlets before upsizing. If a 5-inch gutter is close on capacity, a second 2×3 downspout doubles outlet area to 12.00 square inches, the same as one 3×4, often for less than replacing the whole run with 6-inch gutter.
  • Match outlet to gutter. Berger notes the downspout must not exceed the gutter’s bottom width and the outlet capacity should suit the downspout.

Undersized or too-few downspouts are the most common reason gutters overflow even when the gutter width looks correct. Berger’s appendix puts it directly: the gutter “can never be any more effective than the outlet and downspout selected to drain it”, and a run with 6.00 square inches of outlet where 9 are needed backs up regardless of trough width.

5-inch versus 6-inch: when each is enough

Choose 5-inch gutters when each run drains a moderate, lower-pitched roof section whose design area fits one or two 2×3 downspouts at your rainfall, and choose 6-inch gutters when runs are long, the roof is steep, valleys concentrate flow, or downpours are intense. This Old House rates a 6-inch K-style at about 7,960 square feet against 5,520 for a 5-inch, and it pairs with a 3×4 downspout of 12.00 square inches. For the full cost and capacity breakdown, see our guide on how 5-inch and 6-inch gutters compare.

Six-inch gutters cost more per linear foot and need larger hangers and outlets, so they are not automatically the safe choice. On a small house with several short runs, each under one 2×3’s area for your city, 6-inch gutters can be money spent on capacity the roof never fills. Size the run, then buy the width the number calls for. For sheds, porches and other very small roofs, see our guide to mini gutters.

Does gutter profile change the size you need?

Profile changes how a nominal size translates to capacity, so a 6-inch half-round does not carry as much as a 6-inch K-style. This Old House rates a 6-inch half-round at up to 3,840 square feet against about 7,960 for a 6-inch K-style, and a 5-inch half-round at 2,500 against 5,520 for a 5-inch K-style. If you want the look of half-round, you may need to step up a size or add a downspout to match a K-style’s capacity.

Nominal width is measured across the top opening, which is where people go wrong reading a spec: a 5-inch K-style is 5 inches across the top, not 5 inches deep. To confirm what you already have or need to match, our guide on how to measure gutter size covers the tape and girth methods, and the K-style versus half-round comparison covers the capacity gap between profiles.

Common gutter sizing mistakes

The costly gutter sizing mistakes come from sizing the whole house instead of each run, ignoring the 1.00 to 1.30 pitch factor and local rainfall, and forgetting that slope and downspout count matter as much as width. Each one shows up as overflow, fascia rot, or foundation splashing within a season or two of the wrong call.

  • Sizing by house square footage. A gutter serves one drainage section, not the whole roof. Split the roof and size each run.
  • Skipping the pitch factor. A 12:12 roof needs 30 percent more capacity than its flat footprint suggests.
  • Ignoring local rainfall. The same roof needs different outlets in Seattle (2.1 in/hr) and Tampa (8.3 in/hr). Pull your NOAA intensity before buying.
  • Too few downspouts. Correct width with too little outlet area still overflows. Count outlet square inches and keep sections under 50 feet.
  • Forgetting slope. A correctly sized gutter still floods if it does not drain toward the outlet; Berger treats a gutter pitched 1/16 inch per foot or less as level. See our guide on gutter slope and drop per foot.

Frequently asked questions

What size gutters do I need for my house?

Most houses need 5-inch K-style gutters with 2×3 downspouts. You need 6-inch gutters with 3×4 downspouts when a run’s pitch-adjusted area is more than one or two 2×3 downspouts can drain at your rainfall (about 960 square feet each in Atlanta or Dallas, 1,080 in Chicago), when valleys feed the run, or when the roof is steep. Size each gutter run by the roof area draining into it, not by the total size of the house.

How do I calculate what size gutter I need?

Measure the roof footprint draining to each gutter, multiply by the SMACNA pitch factor (1.00 to 1.30), then divide by the roof area one square inch of downspout drains at your 5-minute rainfall intensity from NOAA Atlas 14 (about 1,200 divided by the in/hr figure). As a flow check, effective area times inches-per-hour rainfall times 0.0104 gives the gallons per minute the gutter must carry.

Are 6-inch gutters worth it over 5-inch?

Six-inch gutters are worth it when runs are long, the roof is large or steep, or rainfall is intense. This Old House rates a 6-inch K-style at about 7,960 square feet of drainage area against 5,520 for a 5-inch, about 44 percent more, and the 3×4 downspout it uses has twice the 6.00 square inches of a 2×3. On a small house with several short runs and moderate rain, 5-inch gutters usually handle the load and cost less.

How many downspouts do I need?

Provide enough downspout cross-section to cover each run’s pitch-adjusted area at your rainfall: roughly 1,200 divided by your 5-minute intensity in square feet per square inch. In Chicago (6.8 in/hr) one 2×3 drains about 1,080 square feet and one 3×4 about 2,160. Keep each gutter section under 50 feet between ends or expansion joints.

Does roof pitch affect gutter size?

Yes. A steeper roof catches more wind-driven rain and sheds it faster, so its gutter must handle more water than a flat roof of the same footprint. SMACNA’s pitch factors run from 1.00 for flat to 3-in-12 roofs, 1.05 at 4 to 5, 1.10 at 6 to 8, 1.20 at 9 to 11, and 1.30 at 12-in-12. Skipping this factor is a common reason steep-roof gutters overflow despite looking correctly sized.

What size downspout goes with a 6-inch gutter?

A 6-inch K-style gutter is normally paired with a 3×4 inch downspout, which has 12.00 square inches of cross-section, and a 6-inch half-round with a 4 inch round (12.57 square inches). A 5-inch K-style typically uses a 2×3 downspout with 6.00 square inches. Pairing a 6-inch gutter with an undersized 2×3 downspout wastes the extra trough capacity, since the outlet becomes the bottleneck.