By The Roofing Brief Team | Last reviewed: October 2026
Gutter repair cost runs $100 to $450 for most jobs, with a $275 national average, according to HomeGuide’s gutter repair cost guide (November 2025). The gap between fixes is wide: a seam reseal is $1.50 to $6.50 per linear foot of sealant, a sagging run is $75 to $300, a pitch adjustment is $75 to $200, and a downspout is $30 to $75 each, while rotted fascia behind the gutter adds $6 to $20 per linear foot before the gutter can go back up. This Old House, using HomeAdvisor estimates (updated June 12, 2026), puts the typical job at $195 to $625 with a $385 average. What you pay depends on which of the five common failures you have, how many linear feet are affected, how many stories the crew has to reach, and whether the fascia is still sound.
What do gutter repair services actually fix?
Gutter repair services address five recurring failures: leaks at seams and joints, sagging runs from failed hangers, clogs that force overflow, damaged or disconnected downspouts, and rotted fascia behind the gutter. Each has a distinct fix and price, so a “gutter repair” quote is only meaningful once the specific failure is named. On HomeGuide’s numbers, a 10 ft fascia replacement at $6 to $20 per linear foot ($60 to $200) can cost as much as the whole $75 to $200 pitch adjustment it sits behind.
Most contractors bill either a flat service minimum or an hourly rate. HomeGuide lists minimum service fees of $75 to $200, usually covering the first hour on site, and labor of $50 to $150 per hour beyond that. Two- and three-story homes add cost because crews need ladders, stabilizers, or lift equipment and more downspout length to reach the ground safely.
Sectional gutters are cheaper to repair than seamless because a technician can swap one damaged length at a time. HomeGuide puts sectional repairs at $100 to $450 and seamless repairs at $150 to $750, because a damaged seamless run often has to be replaced as a whole length with no joint to cut at. That difference is covered in our guide to seamless versus sectional gutters.
What are the most common gutter repairs and what do they cost?
The five most common gutter repairs are leak sealing, sagging correction, clog clearing, downspout repair, and fascia repair. Leak and clog fixes sit at the low end, often under $250, while section replacement runs $75 to $170 for 10 ft and $300 to $850 for 50 ft on HomeGuide’s figures. Match your symptom to a row below; each price names its source.
| Repair type | What fails | Typical cost | Source |
|---|---|---|---|
| Leak / seam reseal | Cracked sealant at seams or joints; pinholes | $100 to $225 per job; sealant $1.50 to $6.50 per linear foot | HomeGuide, Nov 2025 |
| Small hole patch | Rust-through or puncture, patched with roofing cement | $100 to $225 (1-story) | HomeGuide, Nov 2025 |
| Larger hole patch | Hole too big for sealant, covered with metal flashing | $1 to $2 per linear foot of flashing | HomeGuide, Nov 2025 |
| Sagging correction | Loose or failed hangers, spikes pulled out | $75 to $300; hangers $2 to $3 each plus labor | HomeGuide, Nov 2025 |
| Pitch adjustment | Water pooling from wrong slope | $75 to $200 | HomeGuide, Nov 2025 |
| Clog clearing | Debris blocking the trough or downspout | $100 to $250 cleaning; plus $60 to $150 for clogged downspouts | HomeGuide cleaning guide, Nov 2025 |
| Downspout repair or replace | Dented, disconnected, or crushed downspout | $30 to $75 per downspout, or $2 to $4 per linear foot | HomeGuide, Nov 2025 |
| Section replacement | Collapsed or badly damaged length | $6 to $17 per linear foot; $75 to $170 for 10 ft, $300 to $850 for 50 ft | HomeGuide, Nov 2025 |
| Fascia repair behind gutter | Rotted fascia board under the gutter | $6 to $20 per linear foot | HomeGuide, Nov 2025 |
These are labor-and-materials ranges for a typical one-story home. HomeGuide’s height table runs $100 to $300 for one story, $135 to $450 for two stories, and $165 to $750 for three or more stories for common repair jobs. For a fuller picture of gutter pricing including new installs, see our rain gutter cost and options guide. If you only need a condition check, see our guide to gutter inspection cost.
How much does leaking gutter repair cost?
Leaking gutter repair costs $100 to $225 for most one-story homes, per HomeGuide. The technician locates the leak, cleans and dries the surface, then applies a gutter sealant, usually silicone or a butyl-based caulk, across the seam or joint. Sealant to waterproof seams runs $1.50 to $6.50 per linear foot. Small holes are patched with roofing cement ($100 to $225) or metal flashing ($1 to $2 per linear foot) for larger gaps. Leaks are the cheapest repair, but a section that leaks in several spots at once often signals the run is near end of life.
How much does sagging gutter repair cost?
Sagging gutter repair costs $75 to $300, depending on how many sections droop and why. Sag is almost always a weight-and-support problem: ice, wet leaves, or standing water pulls loose hangers away from the fascia. The fix is reattaching or adding hangers ($2 to $3 per hanger plus $50 to $150 per hour labor, per HomeGuide) and correcting pitch. If the fascia board behind the gutter has rotted, that must be replaced first, which pushes the job higher. Rotted fascia is a frequent hidden driver of sag, covered in our guide to fascia rot from gutters.
How do you fix a sagging gutter?
A sagging gutter is fixed by restoring hanger spacing and slope, not by bending the old hanger back. Gutter maker Englert calls for hangers spaced no more than 18 to 24 inches apart and a slope of about 1/4 inch for every 10 feet toward the downspout. The sequence:
- Empty the trough. Remove leaves and standing water first; Englert lists debris weight as the first thing to clear before judging the hangers.
- Find the failed supports. Mark every spike, ferrule or hidden hanger that has pulled out, and measure the gap between the remaining sound hangers. Any gap over 24 inches needs a new hanger.
- Probe the fascia. If a screwdriver sinks into the board, replace that length of fascia ($6 to $20 per linear foot, per HomeGuide) before rehanging; a new hanger will not hold in rotted wood.
- Snap a slope line. Mark a chalk line that drops 1/4 inch per 10 feet toward the outlet: 1 inch over a 40 ft run.
- Rehang to the line. Lift the gutter to the chalk line and screw a new hidden hanger ($2 to $3 each) into solid fascia at every gap, keeping spacing at 24 inches or less.
- Water-test. Run a hose at the high end; water should reach the downspout with no standing pools along the run.
How much does clog and overflow repair cost?
Clog clearing costs $100 to $250 as a full gutter cleaning, plus $60 to $150 when downspouts are clogged, per HomeGuide’s November 2025 cleaning guide. Debris backs up flow, water overflows the front lip, and the added weight can start a sag. A technician clears the trough and downspouts, flushes the system, and checks pitch. If clogs recur every season, the real fix is guards or a cleaning schedule rather than repeat service calls. Our gutter cleaning cost and schedule guide covers how often most homes actually need it.
How much does downspout repair cost?
Downspout repair costs $30 to $75 per downspout, or $2 to $4 per linear foot when a full length is replaced, on HomeGuide’s averages. Common failures are dents, crushed elbows, and downspouts that pull loose from the gutter outlet or the wall. Reattaching a disconnected downspout is a low-cost fix, often inside the $75 to $200 service minimum. Replacing a two-story downspout costs more because of the added length and safe-access requirements. Material moves the price more than anything else:
| Downspout material | Replacement cost per linear foot | Per 10 to 15 ft downspout | Source |
|---|---|---|---|
| Vinyl / PVC | $3 to $4 | $30 to $60 | HomeGuide, Nov 2025 |
| Aluminum | $4 to $5 | $40 to $75 | HomeGuide, Nov 2025 |
| Steel / metal | $6 to $12 | $60 to $180 | HomeGuide, Nov 2025 |
| Seamless | $6 to $17 | $60 to $255 | HomeGuide, Nov 2025 |
| Copper | $15 to $35 | $150 to $525 | HomeGuide, Nov 2025 |
HomeGuide notes most homes have 4 to 5 downspouts that are 10 to 15 ft long, so replacing every aluminum downspout on a typical house runs about $160 to $375 on those figures. Englert recommends that downspouts discharge at least 5 to 10 feet from the house, or into a drainage system; a downspout that dumps at the foundation is worth fixing in the same visit.
How do gutter repair approaches compare over repeated maintenance?
Seam resealing, section replacement and downspout fixes solve different failures, so the cheapest first call is not always the cheapest over three or four service visits. Use the trigger column to decide when a recurring patch should become a section or system replacement.
| Approach | Cost per visit | Fixes | Switch approach when |
|---|---|---|---|
| Seam reseal | $1.50 to $6.50 per LF sealant; $100 to $225 per job | Leaking joints and end caps | The same seam leaks again within a season, or 3 or more seams on one run leak |
| Hanger rehang and pitch reset | $75 to $300 | Sag, pooling, overflow at mid-run | Fascia is soft at the hanger points; replace fascia first at $6 to $20 per LF |
| Section replacement | $6 to $17 per LF | Crushed, split or rusted lengths | Replaced footage approaches half the run |
| Downspout reattach or replace | $30 to $75 each (aluminum $40 to $75) | Dents, crushed elbows, loose straps | The downspout clogs every season: add a guard or larger outlet |
| Full replacement | $900 to $2,550 for 150 LF | Widespread rust, many failing seams | Repairs reach roughly half of this figure |
All prices are from HomeGuide’s November 2025 gutter repair guide; “LF” is linear feet.
What drives gutter repair cost up or down?
Four factors move a gutter repair quote: the number of linear feet affected, home height, gutter material, and whether the fascia behind the gutter is sound. On HomeGuide’s figures, height alone moves a common repair from $100 to $300 at one story to $165 to $750 at three stories, and soft fascia adds $6 to $20 per linear foot. A quote that does not name these four is hard to compare.
- Linear feet affected. An isolated seam leak versus a 20-foot sagging run is the difference between a $100 to $225 leak call and $120 to $350 for 20 ft of new section, per HomeGuide.
- Home height. One-story access is fastest. Two- and three-story work adds ladder stabilizers or lifts and longer downspouts, which HomeGuide prices at $135 to $450 and $165 to $750 for common repairs.
- Material. Aluminum downspouts run $4 to $5 per linear foot and copper $15 to $35, per HomeGuide, and gutter sections follow the same order. Material pricing for full runs is detailed in our gutter installation cost guide.
- Fascia condition. Sound fascia means a straight rehang. Rotted fascia adds $6 to $20 per linear foot of board replacement before the gutter goes back up.
When is gutter repair cheaper than replacement?
Repair is the cheaper choice when the damage is localized and the fascia is sound; replacement wins once repair costs pass roughly 50 percent of a full replacement or the same run fails repeatedly. HomeGuide prices full replacement at $900 to $2,550 for 150 linear feet, so on those numbers repairs above about $450 to $1,275 are the point to price a new system. A single leak, one sagging section, or a dented downspout is almost always worth repairing.
| Situation | Better call | Why |
|---|---|---|
| One leak or one sagging section | Repair | Localized, $75 to $300, fascia usually intact |
| Disconnected or dented downspout | Repair | Often within the $75 to $200 service minimum |
| Hangers more than 24 in apart along the run | Repair: add hangers and reset slope | Englert’s limit is 18 to 24 in spacing |
| Several failing seams across the run | Repair then plan replacement | Patches buy time but signal end of life |
| Widespread rust or repair over 50% of replacement cost | Replace | Repeat patches cost more over two seasons |
| System 20+ years old, recurring failures | Replace | Material fatigue, seamless upgrade avoids joints |
The 50 percent rule is a commonly cited rule of thumb, not a published standard. If a $700 repair estimate lands against a $1,400 replacement, replacement is the sounder spend because it resets the clock on the whole system.
What are the alternatives to searching “gutter repair near me”?
Instead of picking the first “gutter repair near me” result, get three itemized quotes and compare them line by line: repair type, linear feet, material, access method, and warranty. A quote that just says “gutter repair, $450” tells you nothing; one that lists “reseal 18 ft of seam, replace 4 hangers, adjust pitch on north run” is verifiable. Ask whether the crew handles fascia carpentry in house, since a rehang that uncovers rot needs both trades. Owners of commercial buildings can turn to our guide to commercial gutter repair, which covers hiring a contractor and whether the owner or the tenant pays.
- Get three itemized quotes. Insist each names the repair, linear feet, and material, not a lump sum.
- Confirm fascia handling. Ask if they replace rotted fascia or subcontract it, and whether that price is in the quote.
- Check the service minimum. A small fix may cost the same as the $75 to $200 minimum, so bundle several small repairs into one visit.
- Ask about hanger spacing and slope. Ask the crew to state the hanger spacing (24 inches or less) and the slope they will set (about 1/4 inch per 10 feet).
- Ask about warranty. Sealant and reattachment work should carry at least a short labor warranty.
Can you DIY common gutter repairs?
Resealing a small seam, tightening a loose hanger, or clearing a clog can be handled by a homeowner comfortable on a stable ladder, for the cost of sealant ($1.50 to $6.50 per linear foot installed, per HomeGuide) and a few $2 to $3 hangers. Disconnected sections, rotted fascia, crushed two-story downspouts, and section collapse need a trained technician with proper access equipment. The dividing line is height and structure: ground-reachable one-story fixes are fair game, and anything requiring you to lean off a ladder at height is not.
Hiring a contractor for this? If you would rather have a roofer handle gutter repair services, choose one whose record you can check. The Roofing Brief ranks manufacturer-certified roofers in 350 U.S. metros and checks each leader against licence and BBB records, including New York, Los Angeles, Chicago, Dallas, Houston, Miami, Washington, Atlanta, Philadelphia, Phoenix, Boston, Riverside. Find your area in the full index of metro roofer rankings.
Frequently asked questions
How much does gutter repair cost on average?
Gutter repair costs $100 to $450 for most jobs, with a $275 national average, per HomeGuide (November 2025); This Old House, using HomeAdvisor estimates, gives $195 to $625 with a $385 average. Simple fixes like a pitch adjustment start near $75, while 50 ft of section replacement can reach $850. The exact price depends on the repair type, linear feet affected, home height, and whether the fascia behind the gutter is sound.
What is the cheapest gutter repair?
Leak sealing and reattaching a loose hanger or downspout are the cheapest gutter repairs, often $75 to $225 for a one-story home. Resealing a seam runs $1.50 to $6.50 per linear foot of sealant. Many minor fixes fall inside a contractor’s $75 to $200 service minimum, so bundling several small repairs into one visit lowers the effective cost per fix.
How much does it cost to fix a sagging gutter?
Sagging gutter repair costs $75 to $300, depending on how many sections droop. The fix is reattaching or adding hangers, at $2 to $3 per hanger plus labor, and correcting the pitch to about 1/4 inch per 10 feet. If the fascia board behind the gutter has rotted, it must be replaced first at $6 to $20 per linear foot, which raises the total before the gutter can be rehung.
How much does downspout repair cost?
Downspout repair or replacement costs $30 to $75 per downspout, or $2 to $4 per linear foot, per HomeGuide. By material, a 10 to 15 ft downspout runs $30 to $60 in vinyl, $40 to $75 in aluminum, $60 to $180 in steel and $150 to $525 in copper. Two-story downspouts cost more because of the extra length and access.
Is it cheaper to repair or replace gutters?
Repair is cheaper when damage is localized and the fascia is sound, such as one leak, one sagging section, or a dented downspout. Replacement makes more sense once repair costs pass roughly 50 percent of a full replacement, which HomeGuide prices at $900 to $2,550 for 150 linear feet, or when the system is 20-plus years old with recurring failures.
What are the most common gutter repairs?
The five most common gutter repairs are leak sealing at seams and joints, sagging correction from failed hangers, clog clearing, downspout repair or replacement, and fascia repair behind the gutter. Leaks and clogs are the least expensive, often under $250, while section replacement runs $6 to $17 per linear foot and fascia work $6 to $20 per linear foot.
Can I repair gutters myself?
Homeowners can safely handle minor gutter repairs like resealing a small seam, tightening a loose hanger, or clearing a clog, for the price of sealant and $2 to $3 hangers. Disconnected sections, rotted fascia, crushed two-story downspouts, and section collapse need a professional with proper access equipment. Ground-reachable one-story fixes are DIY-friendly and anything requiring work at height is not.