By The Roofing Brief Team. Last reviewed: October 2026.
The price of roofing felt in October 2026 is about $30 to $37 for a 432 sq ft roll of No. 15 felt (4 squares, or $7.50 to $9.24 per square) and $27 to $40 for a 216 sq ft roll of No. 30 felt (2 squares, or $13.50 to $20 per square), based on retail listings on Google Shopping on October 19, 2026. Roofing felt is the black, asphalt-saturated paper that goes between your roof deck and the shingles; roofers also call it felt paper or tar paper. It is a secondary water barrier that sheds rain getting past the shingles, protects the deck during installation, and is part of the tested Class A shingle assembly. A 1,000 sq ft synthetic roll listed at $60 to $119 the same day, or about $6 to $12 per square, so synthetic now undercuts No. 30 felt on material price. Wood shake roofs add a second use: 18-inch strips of No. 30 “shake felt” laid between the courses.
The same product goes by several names on a jobsite and in a quote. Roofing felt, tar paper and asphalt paper all describe asphalt-saturated organic or fibreglass sheet, and the two common weights are written as 15 lb and 30 lb, or as #15 and #30. Those numbers come from the original weight per 100 square feet, and modern rolls no longer hit it: ASTM D226 sets a minimum of 11.5 lb per square for Type I (No. 15) and 26 lb for Type II (No. 30), per a 2019 IIBEC Interface article that traced the standard’s history.
What is roofing felt?
Roofing felt is a base mat of organic fibers (cellulose and recycled paper) or fiberglass, saturated with asphalt so it repels water. It ships in 36-inch-wide rolls: TAMKO’s No. 15 data sheet lists a 144 ft by 36 in roll covering 4 squares, and its No. 30 data sheet lists a 72 ft by 36 in roll (216 sq ft) that nets 204 sq ft once lapped. Both rolls carry printed laying lines at 2, 4 and 17 inches to guide the laps.
Two mat types exist. Organic felt uses a paper or cellulose base and is the classic “tar paper” most people picture. Fiberglass-reinforced felt uses a glass-fiber mat that resists tearing and wrinkling better in humidity. The two code-listed felt standards are ASTM D226 (Type I and Type II) and ASTM D4869 (Types I to IV), so check the roll label for the standard and Type, not just “#15” or “#30”. For the coated first ply on flat roofs, see our guide to base sheet roofing.
The “tar paper” nickname is a holdover from coal-tar products; modern felt is saturated with asphalt, and TAMKO’s No. 15 and No. 30 sheets both describe an “asphalt saturated organic felt.” When a roofer says tar paper, felt paper, or underlayment felt on a quote, ask which ASTM standard and Type is printed on the roll.
What does roofing felt do?
Roofing felt has four jobs on a shingle roof. It is a backup barrier, not the primary waterproofing, but IRC Section R905.1.1 requires underlayment under asphalt shingles, and a deck left bare between tear-off and new shingles is open to rain and foot traffic.
- Secondary water barrier. Wind-driven rain, ice-dam backup, and leaks around nails can drive water past shingles. Felt sheds that water off the deck instead of into the wood, and ASTM D4869 felt must pass a liquid-water transmission test, per IIBEC.
- Deck protection during the job. Once the old roof is off, felt weatherproofs the deck until shingles go down. ASTM D4869’s stated objective, quoted by IIBEC, is felt that lies flat when left exposed for two weeks after application.
- Separation layer. Felt keeps shingles from bonding directly to the deck and reduces “telegraphing,” where deck seams and imperfections show through the finished shingles.
- Fire rating support. Underlayment is part of the tested assembly that lets asphalt shingles carry a Class A fire rating, the highest rating under ASTM E108 and UL 790.
15 lb vs 30 lb roofing felt
The numbers describe the historic weight of enough felt to cover 100 square feet, which roofers call one square. Today’s ASTM D226 minimums are 11.5 lb per square for Type I (No. 15) and 26 lb per square for Type II (No. 30), so No. 30 carries more than twice the asphalt-saturated mass. At October 19, 2026 retail listings, No. 30 cost $13.50 to $20 per square against $7.50 to $9.24 for No. 15, roughly double.
| Property | 15 lb felt (No. 15) | 30 lb felt (No. 30) | Source |
|---|---|---|---|
| Roll size | 36 in x 144 ft (432 sq ft), 4 squares | 36 in x 72 ft (216 sq ft), 204 sq ft net | TAMKO No. 15 and No. 30 data sheets |
| ASTM D226 class | Type I | Type II | ASTM D226; TAMKO |
| ASTM D4869 equivalent | Type II (#13) | Type IV (#26) | IIBEC, Nov 2019 |
| Minimum saturated weight | 11.5 lb per square | 26 lb per square | ASTM D226, per IIBEC |
| Allowed under asphalt shingles where IRC wind design applies | No | Yes | 2021 IRC Table R905.1.1(1) |
| Allowed under clay or concrete tile (D226) | No | Yes | 2021 IRC Table R905.1.1(1) |
| Retail price per roll (Oct 19, 2026) | $29.99 to $36.97 | $27.00 to $39.99 | Google Shopping listings (see price table) |
| Material cost per square | $7.50 to $9.24 | $13.50 to $20.00 | Roll price divided by rated squares |
Choose No. 30 where the code or the job demands it: the 2021 IRC accepts only ASTM D226 Type II or ASTM D4869 Type III or IV under asphalt shingles in areas where wind design is required (IRC Figure R301.2.1.1), and only D226 Type II felt under clay and concrete tile, as our guide to Spanish tile roof cost, styles and lifespan explains. On a 4:12 or steeper shingle roof outside those zones, No. 15 (D226 Type I) meets the code minimum at about half the material cost. Buy by the label, not the nickname: IIBEC reported rolls sleeved “number 30” whose felt weighed 8.0 or 13.0 lb per square instead of 26. One October 2026 listing, a Warrior “30#” roll, names ASTM D4869 Type II, which is the #13 class, not the #26 class.
| If your job is… | Use | Rule or threshold |
|---|---|---|
| Asphalt shingles, slope 4:12 or steeper, no wind-design requirement | One layer of No. 15 (D226 Type I) or better | 2021 IRC Tables R905.1.1(1) and (2) |
| Asphalt shingles, slope 2:12 to under 4:12 | Two layers: 19-inch starter strip, then 36-inch sheets lapped 19 inches | 2021 IRC Table R905.1.1(2); R905.2.2 |
| Asphalt shingles where IRC wind design is required | No. 30 (D226 Type II) or D4869 Type III/IV, cap-nailed on a 12-inch grid | 2021 IRC Tables R905.1.1(1) and (3) |
| Clay or concrete tile | No. 30 (D226 Type II) or another listed tile underlayment | 2021 IRC Table R905.1.1(1) |
| Wood shakes | Deck underlayment plus 18-inch No. 30 interlayment strips | IRC R905.8.3 and R905.8.7 |
| Deck will sit uncovered longer than two weeks | Synthetic rated for longer exposure (ProArmor: up to 90 days) | ASTM D4869 two-week objective; Owens Corning |
| Small patch on an older felt roof | Match the existing felt grade | Keeps lap thickness consistent under existing shingles |
Roofing felt standards and building code
Underlayment is not optional under asphalt shingles: the International Residential Code requires it. Section IRC R905.1.1 requires underlayment for steep-slope coverings, lists the accepted felt types in Table R905.1.1(1), sets application in Table R905.1.1(2) and attachment in Table R905.1.1(3), and requires the roll to bear a label with its ASTM standard and Type. The code text below is quoted from Seattle’s published adoption of the 2021 IRC, Chapter 9.
| Spec or rule | What it covers | Why it matters |
|---|---|---|
| ASTM D226 Type I | No. 15 asphalt-saturated organic felt, 11.5 lb per square minimum | The classic 15 pound felt referenced by code |
| ASTM D226 Type II | No. 30 asphalt-saturated organic felt, 26 lb per square minimum | Heavier grade required under tile and in wind-design areas |
| ASTM D4869 Types I to IV | #8, #13, #20 and #26 felt underlayment | A “#15” sold to D4869 Type II is a #13 product, so specs are not identical |
| IRC Table R905.1.1(2), slope 2:12 to under 4:12 | Two layers: a 19-inch eave strip, then 36-inch sheets lapped 19 inches; end laps 4 inches, offset 6 feet | Low-slope shingle roofs require double coverage, not one pass |
| IRC Table R905.1.1(2), slope 4:12 and steeper | One layer, shingle fashion, lapped 2 inches; end laps 4 inches, offset 6 feet | The single-layer method used on most homes |
| IRC Table R905.1.1(3), wind-design areas | Ring or deformed shank cap nails with 1-inch caps, 12-inch grid, 6-inch spacing at laps | Staples and bare nails do not meet the high-wind attachment rule |
Local amendments can add requirements, such as a self-adhering ice barrier at the eaves in cold climates. Under IRC R905.1.2 that barrier runs from the eave to at least 24 inches inside the exterior wall line, and it is a separate ASTM D1970 product, not felt. See our guide to ice and water shield and when code requires it for where that layer goes.
Shake felt: the interlayment under wood shakes
Shake felt is roofing felt in 18-inch strips laid between the courses of a wood shake roof, a layer the code calls interlayment. The 2021 IRC (Section R905.8.7) requires strips of not less than No. 30 felt shingled between each course, positioned so no felt is exposed to the weather. It goes on in addition to the regular underlayment on the deck, not instead of it.
The Cedar Shake and Shingle Bureau, the cedar industry’s technical authority, says the interlay helps keep wind-driven rain and snow out, and specifies 18-inch No. 30 felt to ASTM D226 Type II or ASTM D4869 Type IV in its technical bulletin on underlayment and interlayment. The code rules below are quoted from Seattle’s adoption of the 2021 IRC, Chapter 9.
| Rule | Requirement | Source |
|---|---|---|
| Strip width | 18 inches | IRC R905.8.7; CSSB |
| Felt grade | Not less than No. 30 (CSSB: ASTM D226 Type II or ASTM D4869 Type IV) | IRC R905.8.7; CSSB |
| Strip position | Lower edge above the butt of the shake it covers by twice the weather exposure | IRC R905.8.7 |
| Visibility | No felt exposed to the weather, including in the gaps (keyways) between shakes | IRC R905.8.7; CSSB |
| Deck underlayment | Still required under the shakes | IRC R905.8.3 |
| Minimum roof slope for shakes | 3:12 | IRC R905.8.2 |
Weather exposure is the length of each shake left showing. At a 10-inch exposure, the bottom edge of each strip sits 20 inches above the butt of the shake it covers. Set it lower and the felt shows between the shakes; the CSSB calls that “rot felting,” because the exposed felt degrades in sunlight and can keep the shakes from drying, which shortens their life. Shake felt is for shakes only: the CSSB says never to interlay wood shingles with felt, since a shingle roof is already a three-ply system.
One code wrinkle: R905.8.4 says interlayment shall comply with ASTM D226 Type I, the No. 15 grade, while R905.8.7 calls for not less than No. 30 felt. No. 30 strips meet the stricter wording, but your building department decides how the two sections are read together.
Price of roofing felt: how much does roofing felt cost?
Felt is one of the cheapest parts of a roof. The table lists retail roll prices shown on Google Shopping on October 19, 2026, converted to price per square using each roll’s rated coverage.
| Product | Roll | Listed price | Per square | Source |
|---|---|---|---|---|
| No. 15 felt (Tahlequah Lumber, ASTM) | About 432 sq ft, 4 squares | $29.99 | $7.50 | Google Shopping, Oct 19, 2026 |
| No. 15 felt (Arnold Lumber) | 432 sq ft, 4 squares | $32.99 | $8.25 | Google Shopping, Oct 19, 2026 |
| No. 15 felt, ASTM D226 (GR Mitchell) | 432 sq ft, 4 squares | $33.72 | $8.43 | Google Shopping, Oct 19, 2026 |
| Reliabilt #15 (Lowe’s) | 36 in x 144 ft, 432 sq ft | $36.97 | $9.24 | Google Shopping, Oct 19, 2026 |
| 30 lb felt (Cowls Building Supply) | 216 sq ft, 2 squares | $27.00 | $13.50 | Google Shopping, Oct 19, 2026 |
| Warrior 30# felt, listed as ASTM D4869 Type II (Arbor) | 2 squares | $31.00 | $15.50 | Google Shopping, Oct 19, 2026 |
| Reliabilt #30 (Lowe’s) | 36 in x 72 ft, 216 sq ft | $36.97 | $18.49 | Google Shopping, Oct 19, 2026 |
| Orgill 30RF (Do it Best) | 72 ft roll, 2 squares | $39.99 | $20.00 | Google Shopping, Oct 19, 2026 |
| Barricade UDL Standard synthetic (Doug Ashy) | 10 squares | $60.15 | $6.02 | Google Shopping, Oct 19, 2026 |
| Owens Corning ProArmor synthetic (Home Depot) | 42 in x 286 ft, 10 squares | $119.00 | $11.90 | Google Shopping, Oct 19, 2026 |
For a whole-roof budget, HomeGuide’s underlayment replacement cost guide (April 2024) puts asphalt felt materials at $0.05 to $0.15 per square foot and labor to replace roofing felt at $0.65 to $3.20 per square foot, for $0.75 to $4.00 per square foot all in. Most contractors fold the underlayment into the reroof bid rather than pricing it separately, so ask for the felt grade and roll count as a line item. Asphalt-based roofing products track petroleum and freight prices; The Roofing Brief follows those swings in our roofing material price and inflation index, built from BLS producer price data.
Worked example: felt for a 25-square roof
| Option (25 squares, slope 4:12 or steeper, one layer) | Rolls needed | Material at Oct 19, 2026 listings |
|---|---|---|
| No. 15 felt, 4 squares per roll | 7 (25 / 4 = 6.25, rounded up) | $209.93 to $258.79 |
| No. 30 felt, 204 sq ft net per roll (TAMKO) | 13 (2,500 / 204 = 12.25, rounded up) | $351.00 to $519.87 |
| Synthetic, 929 sq ft net per roll (ProArmor with 3-inch laps) | 3 (2,500 / 929 = 2.69, rounded up) | $180.45 to $357.00 |
| No. 15 felt on a 2:12 to 4:12 slope (two layers) | About 13 (double coverage) | $389.87 to $480.61 |
On this 2,500 sq ft example, stepping up from No. 15 to No. 30 adds about $141 to $261 in material at the listed prices. The low-slope row doubles the felt because IRC Table R905.1.1(2) laps each 36-inch sheet 19 inches. Add drip edge, cap nails and any ice barrier at the eaves separately.
Roofing felt vs synthetic underlayment
Synthetic underlayment is a woven or spunbond polymer sheet that replaces felt on many new roofs. Owens Corning’s ProArmor, for example, is a 10-square roll (42 in x 286 ft) that weighs 25 lb, covers 929 sq ft with 3-inch overlaps, and is rated for up to 90 days of UV exposure with a 10-year limited warranty. That is about 2.5 lb per square against the 26 lb per square ASTM minimum for No. 30 felt. At October 19, 2026 listings, synthetic cost $6.02 to $11.90 per square, below No. 30 felt and close to No. 15.
| Factor | Roofing felt | Synthetic underlayment | Source |
|---|---|---|---|
| Material cost per square | $7.50 to $9.24 (No. 15); $13.50 to $20 (No. 30) | $6.02 to $11.90 | Google Shopping, Oct 19, 2026 |
| Weight | 11.5 to 26 lb per square minimum | About 2.5 lb per square (ProArmor) | ASTM D226 via IIBEC; Owens Corning |
| Roll coverage | 2 to 4 squares per roll | 10 squares per roll | TAMKO; Owens Corning |
| UV and exposure tolerance | D4869 objective: lie flat for 2 weeks exposed | Up to 90 days (ProArmor) | IIBEC; Owens Corning |
| Best fit | Repairs, code minimum, historic matching, shake interlayment | Full reroofs, steep roofs, exposure over 2 weeks | Editorial, from the rows above |
For the full breakdown, see felt vs synthetic roof underlayment, and for product picks see our ranking of the best synthetic underlayment brands. Check the shingle maker’s list of approved underlayments before swapping either product into a warranted system.
How roofing felt is installed
Felt goes on from the bottom of the roof upward, so every course overlaps the one below and water always runs onto the top surface, never behind it. The sequence on a standard 4:12-or-steeper shingle roof, per IRC Table R905.1.1(2):
- Confirm the deck is dry and sound. Never lay felt over wet sheathing, which can trap moisture and grow mold under the roof.
- Install drip edge at the eave first, then run the first felt course along the eave, aligned straight on the 36-inch roll width.
- Work up the roof, lapping each course over the one below by at least 2 inches (use the printed 2-inch laying line) and lapping roll ends 4 inches, with end laps offset 6 feet course to course.
- On a 2:12 to under 4:12 slope, start with a 19-inch strip at the eave, then lap each 36-inch sheet 19 inches over the one below for two full layers.
- Fasten enough to hold the felt in place; where IRC wind design applies, use ring or deformed shank nails with 1-inch metal or plastic caps on a 12-inch grid, 6 inches apart at laps (Table R905.1.1(3)).
- Cover with shingles promptly. ASTM D4869 targets felt that stays flat for two weeks of exposure; plan the shingle install inside that window.
Is roofing felt still worth using?
Roofing felt is still a code-listed underlayment under IRC Table R905.1.1(1), and it wins on small repairs, patch-ins that must match an older felt roof, wood-shake interlayment (which must be No. 30 felt under IRC R905.8.7), and any job where the deck will be covered within two weeks. Its weaknesses are weight (11.5 to 26 lb per square minimum), tearing, wrinkling when wet, and the short exposure window.
For a full reroof, a 10-square synthetic roll at $6 to $12 per square now costs about the same as No. 15 felt and less than No. 30, weighs about a tenth as much as No. 30, and carries a maker-rated exposure window of up to 90 days in the ProArmor example. Felt has moved from the default to the code-minimum option. Match the product to the slope (two layers below 4:12), the wind-design zone (No. 30 or D4869 Type III/IV), and the weather window. For the full menu of options, see our guide to roof underlayment types and when each is required, and for one synthetic line compared by grade, our Titanium UDL underlayment review. We break down the cost, weight and code differences in roofing felt vs synthetic underlayment.
Frequently asked questions
What is the price of roofing felt?
Retail listings on October 19, 2026 put a 432 sq ft roll of No. 15 felt at $29.99 to $36.97 ($7.50 to $9.24 per square) and a 216 sq ft roll of No. 30 felt at $27.00 to $39.99 ($13.50 to $20 per square). HomeGuide (April 2024) puts installed underlayment replacement at $0.75 to $4.00 per square foot including labor.
Is roofing felt the same as tar paper?
Yes. Tar paper, felt paper, and roofing felt all describe the same product: an asphalt-saturated mat used as roof underlayment. The “tar” name is historic; TAMKO’s No. 15 and No. 30 data sheets both describe asphalt saturated organic felt. Check the roll label for ASTM D226 or D4869 and the Type.
Do you need felt under shingles?
You need underlayment under shingles, not necessarily felt. IRC R905.1.1 requires underlayment beneath asphalt shingles, and Table R905.1.1(1) accepts ASTM D226 Type I or II felt, ASTM D4869 felt, or ASTM D6757 underlayment, with only D226 Type II or D4869 Type III/IV allowed where wind design is required. Synthetic underlayment is used under the maker’s code evaluation report.
What is the difference between 15 lb and 30 lb roofing felt?
ASTM D226 sets a minimum of 11.5 lb per square for Type I (No. 15) and 26 lb per square for Type II (No. 30). A No. 15 roll covers 4 squares and a No. 30 roll 2 squares, per TAMKO’s data sheets. At October 2026 retail listings, No. 30 cost about twice as much per square, and the IRC requires it under tile and in wind-design areas.
How long can roofing felt be left exposed?
Plan on two weeks or less. ASTM D4869’s stated objective is felt that lies flat and resists wrinkling when left exposed for two weeks after application, per IIBEC. HomeGuide warns felt may tear or wrinkle within hours in bad weather. Synthetics run longer: Owens Corning rates ProArmor for up to 90 days of UV exposure.
Is felt or synthetic underlayment better?
For a full reroof, synthetic usually is: Owens Corning’s ProArmor weighs about 2.5 lb per square, covers 929 sq ft per roll, and allows up to 90 days of exposure, and 10-square synthetic rolls listed at $6 to $12 per square in October 2026. Felt still fits small repairs, shake interlayment, and code-minimum jobs covered within two weeks. Both meet code when installed correctly.