A metal roofing gauge chart runs from 29 gauge (about 0.014 in) for sheds to 22 gauge (about 0.030 in) for heavy commercial roofs, and gauge is one of four numbers that set the price of roofing sheet metal: base metal, gauge, coating, and coverage width. A 29 gauge galvanized corrugated sheet and a 24 gauge Kynar 500 Galvalume sheet are both sold as a “roofing sheet” but sit at opposite ends of the price table below.
By The Roofing Brief Team. Last reviewed: October 2026. Installed cost per square foot for a whole roof is in the metal roof cost guide, and profiles are in metal roofing types.
What is roofing sheet metal, and how is it sold?
Roofing sheet metal is a roll formed panel of coated steel or aluminum, sold by width and length rather than by the square. A 26 inch nominal corrugated sheet covers about 24 inches after overlap; an R panel sheet nominal 36 inches covers 36. You pay for the nominal sheet but cover the roof with the coverage width, and that gap is where buyers overspend.
Exposed fastener sheets (corrugated, R panel, PBR) screw through the face and cost least; standing seam sheets (12 to 19 inch coverage) hide the fasteners under a raised seam and are roll formed to full slope length. Crews that roll form on site buy flat coil instead of sheets, priced by the square foot or by the pound; our guide to metal roofing coil sizes and prices lists widths, weights and October 2026 coil listings.
How do metal roofing sheet gauges compare?
Gauge is steel thickness, and a lower number is thicker and costs more. Residential and light commercial sheet runs from 29 gauge (about 0.014 in) to 22 gauge (about 0.030 in), so a 24 gauge sheet is roughly 1.6 times the steel of 29 gauge, which shows in dent resistance and oil canning. Our guide to 22 gauge metal roofing explains where the thickest panel is worth its price.
| Gauge | Steel thickness | Typical use | Relative sheet price |
|---|---|---|---|
| 29 gauge | about 0.014 in | Sheds, barns, budget exposed fastener | Lowest |
| 26 gauge | about 0.018 in | Standard exposed fastener (corrugated, PBR) | Baseline |
| 24 gauge | about 0.023 in | Standard standing seam, premium exposed fastener | Above 26 gauge |
| 22 gauge | about 0.030 in | Heavy commercial, high wind, long spans | Highest steel tier |
Treat 26 gauge as the floor for an exposed fastener roof meant to last past 20 to 25 years, and 24 gauge as the standard for standing seam, where the wide flat pan oil cans on thinner steel. Englert puts standard roofing panels at 1.0 to 1.5 pounds per square foot, and Galvalume and galvanized panels of the same gauge and profile weigh nearly the same. Panel texture also hides waviness; see striated vs flat metal panels.
How do sheet coatings change the price?
Coating is the biggest price lever after gauge and has two layers: a metallic coat (G90 zinc, or AZ50 or AZ55 zinc aluminum) stops corrosion at the steel, and the paint (PVDF or SMP) stops fading and chalking.
| Coating layer | Option | What it does | Price effect |
|---|---|---|---|
| Metallic base | Galvanized G90 | Zinc coat to ASTM A653 G90, standard corrosion resistance | Cheapest base |
| Metallic base | Galvalume AZ50 / AZ55 | Zinc aluminum coat, better long term corrosion, AZ55 is the heavier coat | Priced 5% to 15% above galvanized of the same gauge and profile (Englert) |
| Paint finish | SMP (silicone modified polyester) | Economy paint, chalks and fades sooner, shorter warranty | Low added cost |
| Paint finish | PVDF (Kynar 500) | Fluoropolymer, best fade and chalk resistance per McElroy Metal; paint warranty terms differ by maker | Premium: ask for PVDF and SMP prices on the same panel |
Englert rates galvanized steel at 20 to 50 years and Galvalume at 40 to 70, and McElroy Metal says PVDF (Kynar 500) gives the best protection against fade and chalk of the three common coatings (PVDF, SMP, polyester). A bare Galvalume sheet is the cheapest durable option; a PVDF painted 24 gauge sheet is the durable premium.
What sizes do roofing sheets come in?
Exposed fastener corrugated and R panel sheets run 26 to 36 inches nominal width with 24 to 36 inches of coverage, cut in 6 to 12 foot stock lengths; standing seam is roll formed to the exact rafter length.
- Corrugated (7/8 in wavy): about 26 in nominal, roughly 24 in coverage, 8 or 12 ft common lengths.
- R panel / PBR: 36 in nominal, 36 in coverage, cut to length.
- Standing seam: 12 to 19 in coverage per panel, roll formed to the full slope length.
A 36 inch coverage sheet covers 50 percent more roof than a 24 inch coverage sheet of the same length (36 / 24 = 1.5), so a pricier wide panel can cost less installed. Divide each sheet price by its coverage area before comparing quotes, then count panels with the metal roofing calculator.
How much does roofing sheet metal cost per sheet in 2026?
The planning ranges below for a 3 foot by 8 foot steel sheet are editorial estimates, not a dated retailer snapshot, so confirm at the supply house: galvanized 29 to 26 gauge sits at the bottom, Galvalume and SMP in the middle, PVDF 24 gauge at the top, and aluminum above steel. They are material only, before fasteners, trim, and labor; This Old House reports roofers ordering about 10% extra metal for waste. Englert finishes are in our Englert metal roofing review.
| Sheet type (3 ft x 8 ft footprint) | Gauge | Coating | Price per sheet (2026) |
|---|---|---|---|
| Galvanized corrugated | 29 | G90 bare | $30 to $55 |
| Galvalume corrugated / R panel | 26 | AZ50 bare | $45 to $75 |
| Painted exposed fastener | 26 | SMP | $60 to $95 |
| Painted premium sheet | 24 | PVDF (Kynar 500) | $95 to $130 |
| Aluminum panel | 0.032 in | Painted | $120 to $180 |
Steel prices move quarter to quarter. Corrugated is the cheapest sheet family; see the corrugated roof panel guide.
How do you read a roofing sheet spec before buying?
A counter listing like “26 ga AZ55 SMP PBR panel, 36 in coverage” reads as gauge (26), base coat (Galvalume AZ55), paint (SMP), profile (PBR), and coverage width (36 in). Miss any one and two “identical” quotes are not the same panel.
- Profile and fastener family. Corrugated, R panel, PBR, or standing seam. This sets the base price tier and the exposed vs hidden fastener choice.
- Gauge. 29, 26, 24, or 22. Thicker (lower number) resists dents and oil canning and costs more.
- Metallic coating. Galvanized G90, or Galvalume AZ50 / AZ55. Galvalume lasts longer in most climates; AZ55 is the heavier coat.
- Paint finish. Bare, SMP, or PVDF (Kynar 500). PVDF holds color and carries the 40 year warranty; SMP is the budget paint.
- Coverage width. Divide price by coverage area to compare true cost, not by the nominal sheet size.
Which roofing sheet should you buy?
The cheapest sheet that meets the exposure wins; the table matches building type to spec.
| If your roof is | Then buy | Why |
|---|---|---|
| Shed, barn, or carport | 29 gauge galvanized or bare Galvalume corrugated | Lowest cost for a low stakes structure |
| Long term exposed fastener roof | 26 gauge Galvalume with SMP or PVDF paint | 26 gauge is the floor past 20 to 25 years |
| Premium residential standing seam | 24 gauge Galvalume with PVDF (Kynar 500) | Rigid pan resists oil canning; best fade and chalk protection |
| High wind or heavy commercial | 22 gauge with PVDF | Span and impact; finish for longevity |
Coastal and high UV sites push the choice to Galvalume and PVDF at any gauge. Between two sheets that meet the exposure, buy the 36 inch coverage width over 24 inch: 1.5 times the roof per sheet.
Related: Metal Deck Roofing: Types, Gauge, Span, and Cost (2026)
Roofing sheet metal FAQ
What gauge is best for roofing sheet metal?
Use 26 gauge as the minimum for an exposed fastener roof meant to last past 20 to 25 years, and 24 gauge for standing seam. 29 gauge suits sheds; 22 gauge suits heavy commercial and high wind.
How much does a sheet of metal roofing cost?
Plan on about $30 to $130 for a 3 foot by 8 foot steel sheet, material only: $30 to $75 for galvanized 29 to 26 gauge, $60 to $95 for SMP painted, $95 to $130 for 24 gauge PVDF, and $120 to $180 for aluminum (editorial ranges; confirm at the supply house).
What is the difference between galvanized and Galvalume sheets?
Galvanized sheets carry a zinc coating (commonly G90); Galvalume uses a zinc aluminum alloy (AZ50 or AZ55). Englert rates Galvalume at 40 to 70 years against 20 to 50 for galvanized, and prices it 5% to 15% higher at the same gauge and profile.
Is Kynar 500 worth the extra cost on a sheet?
Usually yes on a permanent roof: McElroy Metal says PVDF (Kynar 500) gives the best protection against fade and chalk of the common coatings. On a shed, SMP or bare Galvalume is fine. Compare paint warranty terms between makers.
What size are metal roofing sheets?
Exposed fastener sheets run 26 to 36 inches nominal with 24 to 36 inches of coverage, in 6 to 12 foot stock lengths. Standing seam panels cover 12 to 19 inches but run the full slope length. Compare by coverage width.
How many roofing sheets do I need?
Divide the roof area by each sheet’s coverage area (coverage width times length) and add about 10 percent for waste. A 1,000 square foot roof needs 42 sheets of 8 foot by 3 foot coverage (24 square feet each) before the waste allowance.