By The Roofing Brief Team. Last reviewed: October 2026.
IRC R905.1.1 requires two layers of underlayment on asphalt shingle roofs with slopes from 2:12 up to 4:12, and one layer at 4:12 and steeper. In the 2021 International Residential Code, Table R905.1.1(2) spells out the two-layer method (a 19 inch strip at the eave, then 36 inch sheets lapped 19 inches) and the single-layer method (lapped 2 inches, end laps 4 inches offset 6 feet). IRC Section R905.2.2 sets the 2:12 floor for shingles and points to IRC R905.1.1 for the double-layer trigger. So the answer to “for roof slopes from 2:12 to 4:12, how many layers of underlayment” is two. In Florida, see our guide to Florida building code roof requirements, which covers the secondary water barrier.
Every other roof covering carries its own minimum slope and its own IRC section, and several of them defer the underlayment method to the manufacturer except in regions where IRC Figure R301.2.1.1 requires wind design. The reference table pairs each covering with its slope floor, its underlayment rule, and the governing section.
What IRC R905.1.1 requires: the three underlayment tables
Section R905.1.1 of the 2021 IRC covers underlayment for asphalt shingles, clay and concrete tile, metal roof shingles, mineral-surfaced roll roofing, slate, wood shingles and shakes, metal panels and photovoltaic shingles. It works through three tables, each split into two columns: areas where wind design is not required, and areas where wind design is required under IRC Section R301.2.1.1 and Figure R301.2.1.1 (mapped regions that include hurricane-prone coastal areas, plus special wind regions where Vult is 140 mph or more).
| 2021 IRC item | Wind design not required | Wind design required (Figure R301.2.1.1) | Source |
|---|---|---|---|
| Table R905.1.1(1), types for asphalt shingles | ASTM D226 Type I or II, ASTM D4869 Type I to IV, or ASTM D6757 | ASTM D226 Type II, or ASTM D4869 Type III or IV | IRC 2021 Table R905.1.1(1) |
| Table R905.1.1(1), types for clay and concrete tile | ASTM D226 Type II, ASTM D2626 Type I, or ASTM D6380 Class M roll roofing | ASTM D226 Type II | IRC 2021 Table R905.1.1(1) |
| Table R905.1.1(2), application on asphalt shingles | Two layers (19 in. method) from 2:12 to 4:12; one layer lapped 2 in. at 4:12 and up | Two layers (19 in. method) at every slope | IRC 2021 Table R905.1.1(2) |
| Table R905.1.1(2), metal shingles, roll roofing, slate, wood, metal panels | Manufacturer’s installation instructions | Two layers (19 in. method), end laps 4 in. offset 6 ft | IRC 2021 Table R905.1.1(2) |
| Table R905.1.1(3), attachment | Fastened sufficiently to hold in place (shingles, tile, PV); manufacturer’s instructions (others) | Ring or deformed shank cap nails, 1 in. caps, 12 in. grid between side laps, 6 in. at side and end laps | IRC 2021 Table R905.1.1(3) |
| Exception 1 | One layer of ASTM D1970 self-adhering polymer-modified bitumen, installed per both the underlayment and roof covering makers’ instructions | IRC 2021 R905.1.1 Exception 1 | |
| Exception 2 | 4 in. wide ASTM D1970 strips over all deck joints, then the normal-wind underlayment over the whole roof | IRC 2021 R905.1.1 Exception 2 | |
The attachment column has hard numbers in the wind design regions: metal caps of not less than 32 gauge sheet metal (power-driven caps 0.010 inch minimum), plastic cap edges at least 0.035 inch thick, a cap nail shank of not less than 0.083 inch, and a shank long enough to go through the sheathing or at least 3/4 inch into it. The 2024 IRC version of R905.1.1 is reworded, so confirm which edition your building department enforces before quoting a table number.
Which underlayment method applies to your roof?
| If your roof is | Then the 2021 IRC requires | Section |
|---|---|---|
| Asphalt shingles below 2:12 | No shingle option; switch to a low slope covering (modified bitumen, TPO, EPDM, standing seam at 1/4:12) | R905.2.2 |
| Asphalt shingles, 2:12 up to 4:12 | Two layers: 19 in. eave strip, 36 in. sheets lapped 19 in., end laps 4 in. offset 6 ft; or one layer of ASTM D1970 self-adhering membrane | R905.2.2, Table R905.1.1(2), Exception 1 |
| Asphalt shingles, 4:12 or steeper | One layer, lapped 2 in., end laps 4 in. offset 6 ft | Table R905.1.1(2) |
| Clay or concrete tile, 2 1/2:12 up to 4:12 | Two layers (19 in. method) | R905.3.2, Table R905.1.1(2) |
| Any slope in a region where Figure R301.2.1.1 requires wind design | Two layers (19 in. method) under shingles and tile, plus cap-nail attachment on a 12 in. grid | Tables R905.1.1(2) and R905.1.1(3) |
| Synthetic underlayment, 2:12 up to 4:12 | Laps from the product’s ICC-ES report (for example, lapped to the centerline of the course below under ESR-2945) | R905.1.1 via the evaluation report |
| Florida High-Velocity Hurricane Zone, Vult 170 mph or more | Metal caps on the underlayment cap nails | FBC Building 1518.2.1 (8th edition) |
Underlayment slope requirements by roof covering: the IRC reference table
The IRC assigns each roof covering a minimum slope in its own subsection of R905, then routes the underlayment method through Table R905.1.1(2). Asphalt shingles and tile get prescriptive lap dimensions in that table. Metal shingles, slate, wood, and metal panels are handed to the manufacturer’s instructions, except where Figure R301.2.1.1 requires wind design, where the code imposes the two-layer 19 inch method.
| Roof covering | Minimum slope | Underlayment requirement | IRC section |
|---|---|---|---|
| Asphalt shingles | 2:12 (17 percent) | Two layers from 2:12 to under 4:12; one layer lapped 2 in. at 4:12 and above; two layers at every slope where wind design is required | R905.2.2, Table R905.1.1(2) |
| Clay and concrete tile | 2 1/2:12 (21 percent) | Two layers from 2 1/2:12 to under 4:12; one layer lapped 2 in. at 4:12 and above; two layers at every slope where wind design is required | R905.3.2, Table R905.1.1(2) |
| Metal roof shingles | 3:12 (25 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.4.2, Table R905.1.1(2) |
| Mineral surfaced roll roofing | 1:12 (8 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.5.2, Table R905.1.1(2) |
| Slate and slate type shingles | 4:12 (33 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.6.2, Table R905.1.1(2) |
| Wood shingles | 3:12 (25 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.7.2, Table R905.1.1(2) |
| Wood shakes | 3:12 (25 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.8.2, Table R905.1.1(2) |
| Built up roof | 1/4:12 (2 percent); coal tar 1/8:12 (1 percent) | No prescriptive underlayment row; per the roof system | R905.9.1 |
| Metal roof panels, lapped nonsoldered seam, no sealant | 3:12 (25 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.10.2, Table R905.1.1(2) |
| Metal roof panels, lapped nonsoldered seam with sealant | 1/2:12 (4 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.10.2, Table R905.1.1(2) |
| Metal roof panels, standing seam | 1/4:12 (2 percent) | Manufacturer’s instructions; two layers (19 in. method) where wind design is required | R905.10.2, Table R905.1.1(2) |
| Modified bitumen | 1/4:12 (2 percent) | No prescriptive underlayment row; per the roof system | R905.11.1 |
| Thermoset single ply (EPDM) | 1/4:12 (2 percent) | No prescriptive underlayment row; per the roof system | R905.12.1 |
| Thermoplastic single ply (TPO, PVC) | 1/4:12 (2 percent) | No prescriptive underlayment row; per the roof system | R905.13.1 |
| Sprayed polyurethane foam | 1/4:12 (2 percent) | No prescriptive underlayment row; per the roof system | R905.14.1 |
| Liquid applied coating | 1/4:12 (2 percent) | No prescriptive underlayment row; per the roof system | R905.15.1 |
Slopes are quoted from the 2021 IRC. States amend Chapter 9 and renumber sections, so confirm against the edition your jurisdiction has adopted before you rely on a section number in a submittal.
Asphalt shingles: 2:12 minimum, double underlayment below 4:12
IRC R905.2.2 reads: asphalt shingles shall be used only on roof slopes of two units vertical in 12 units horizontal (2:12) or greater. For roof slopes from 2:12 up to 4:12, double underlayment application is required in accordance with Section R905.1.1. Below 2:12 there is no shingle option in the IRC at all. The roof has to change covering, not just change underlayment. Many of those low-slope systems start with a mechanically fastened or adhered first ply; see our guide to base sheets under low-slope membranes.
2:12 works out to a 9.5 degree pitch and 4:12 to 18.4 degrees. The band between them is where water moves slowly enough that wind driven rain and capillary action can push it back up under a shingle course, which is what the second layer of underlayment is there to catch.
The 19 inch lap method, step by step
Table R905.1.1(2) prescribes a specific geometry for the 2:12 to under 4:12 band. The 19 inch starter strip and the first 36 inch sheet both begin at the eave, so a starter strip set above the eave line leaves the bottom course single-layered and out of compliance.
- Apply a 19 inch strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold it in place.
- Starting at the eave again, apply a 36 inch wide sheet of underlayment over that strip. It covers the 19 inch strip completely and extends 17 inches above it.
- Apply each successive 36 inch sheet overlapping the sheet below it by 19 inches, working up the slope in shingle fashion.
- Keep the underlayment flat. The code states that distortions in the underlayment shall not interfere with the ability of the shingles to seal.
- Offset end laps by 6 feet so the vertical seams never stack from course to course.
Why the lap is 19 inches and not 18
The arithmetic is the point. A 36 inch sheet lapped 19 inches leaves 17 inches of exposure per course. Because the exposure is smaller than half the sheet width, every point on the deck ends up with about 2.1 layers over it rather than exactly two. The extra inch is the code’s margin against roll width tolerance and sloppy chalk lines.
| Slope band | Layers | Head lap | Exposure per course | Coverage over any point |
|---|---|---|---|---|
| 2:12 to under 4:12 | Two | 19 in. | 17 in. | About 2.1 layers |
| 4:12 and above | One | 2 in. | 34 in. | About 1.06 layers |
That table also explains the material takeoff. A nominal 36 inch by 144 foot roll of ASTM D226 felt covers roughly 408 square feet at 34 inch exposure and roughly 204 square feet at 17 inch exposure. Dropping from 4:12 to 3:12 does not add a little underlayment. It doubles the felt on the job, and estimators who price a low slope section at single layer rates lose the difference.
Single layer at 4:12 and above
At 4:12 or greater, Table R905.1.1(2) permits one layer applied shingle fashion, parallel to and starting from the eave and lapped 2 inches. End laps are 4 inches and are offset by 6 feet. This is the familiar single course felt or synthetic run that most residential jobs use, and it is the only case where the 2 inch head lap applies.
Synthetic underlayment uses different lap dimensions at the same slope
Table R905.1.1(2) is written around felt widths. Synthetic underlayments are not listed by ASTM standard in Table R905.1.1(1) the way ASTM D226, D4869, D6757 and D1970 products are, so they are approved as alternative materials through an ICC-ES evaluation report, and that report, not the felt table, sets the laps.
ICC-ES report ESR-2945, covering Grip-Rite ShingleLayment synthetic roofing underlayments from PrimeSource Building Products (reissued March 2025, revised September 2025), specifies 4 inch head laps and 6 inch end laps for normal slope work. For slopes from 2:12 up to 4:12 under asphalt shingles, or 2 1/2:12 up to 4:12 under concrete or clay tile, it requires the underlayment to be lapped 24 inches to the centerline of the underlying course to form two layers, with 6 inch end laps.
ESR-5197, covering the Fast Layment synthetic underlayments with Atlas Roofing Corporation among the listees (reissued December 2025, revised June 2026), carries the same centerline lap language for the 2:12 to 4:12 band.
| Product type | Governing document | Low slope lap (2:12 to under 4:12) | Normal slope lap (4:12 and up) |
|---|---|---|---|
| Asphalt saturated felt | IRC Table R905.1.1(2) | 19 in. head lap on 36 in. sheets, over a 19 in. eave strip | 2 in. head lap, 4 in. end lap |
| Synthetic, per ESR-2945 and ESR-5197 | ICC-ES evaluation report | Lapped to the centerline of the course below (24 in. on a 48 in. roll), 6 in. end laps | 4 in. head lap, 6 in. end lap |
Both methods deliver two layers. The numbers differ because the roll widths differ, so quoting the 19 inch figure on a synthetic job is wrong in the same way quoting 24 inches on a felt job is wrong. Pull the ESR for the specific product before the low slope section goes down. Our Titanium UDL underlayment review and the felt vs synthetic underlayment comparison cover how the two material families differ on weight, tear strength, and exposure limits.
ESR-2945 also sets a hard floor in its conditions of use: installation is limited to roofs with a minimum slope of 2:12 or greater. A synthetic underlayment does not extend a shingle roof below the code minimum, and neither does doubling it.
Tile, metal, slate and wood: each covering has its own slope floor
Clay and concrete tile under IRC R905.3.2 starts at 2 1/2:12, half a unit above asphalt shingles, and carries its own double underlayment band from 2 1/2:12 up to 4:12 using the same 19 inch pattern: a 19 inch strip at the eave, then 36 inch strips overlapping successive sheets 19 inches. At 4:12 and above tile drops to a single layer lapped 2 inches with 4 inch end laps offset 6 feet.
Metal roof shingles (R905.4.2) and wood shingles and shakes (R905.7.2, R905.8.2) all sit at 3:12. Slate and slate type shingles (R905.6.2) are the steepest requirement in R905 at 4:12, which means slate never enters the double underlayment band at all. Switching a shallow roof to a covering with a higher slope floor can mean raising a roof pitch, which is a framing project rather than a reroof. Mineral surfaced roll roofing (R905.5.2) goes lowest of the steep slope coverings at 1:12.
Metal roof panels under R905.10.2 split three ways by seam type: 3:12 for lapped, nonsoldered seams without applied lap sealant, 1/2:12 for the same seams with sealant, and 1/4:12 for standing seam systems. That is why a standing seam panel can run on a porch roof where a shingle cannot. See the metal roofing underlayment guide for the material side of those assemblies.
For all of these coverings, Table R905.1.1(2) sends the installer to the manufacturer’s installation instructions outside the wind design regions. The code only writes its own prescription (two layers, 19 inch laps, 4 inch end laps offset 6 feet) where Figure R301.2.1.1 requires wind design.
High wind: two layers at every slope where wind design is required
Where IRC Figure R301.2.1.1 requires wind design, the 2021 IRC Table R905.1.1(2) drops the slope split for asphalt shingles and tile: underlayment shall be two layers at every slope, using the same 19 inch eave strip and 36 inch sheets lapped 19 inches, with 4 inch end laps offset 6 feet. A 6:12 shingle roof in that region gets the same double layer as a 3:12 roof elsewhere. Table R905.1.1(1) also narrows the material to ASTM D226 Type II felt or ASTM D4869 Type III or IV, and Table R905.1.1(3) requires cap nails on a 12 inch grid.
In that same wind band, metal roof shingles, mineral surfaced roll roofing, slate, wood shingles, wood shakes and metal panels stop deferring to the manufacturer and take the two layer 19 inch method, with end laps of 4 inches offset by 6 feet. The older “140 mph, all laps not less than 4 inches” wording that many guides quote comes from the commercial code: IBC Table 1507.1.1(2) still splits its columns at a basic design wind speed of 140 mph and adds 4 inch laps above it.
Florida’s High-Velocity Hurricane Zone (Miami-Dade and Broward) goes further. Section 1518.2.1 of the 2023 Florida Building Code, Building (8th edition), requires underlayment cap nails with caps at least 1 inch in diameter and requires metal caps where the ultimate design wind speed, Vult, equals or exceeds 170 mph, per Miami-Dade’s summary of the 8th edition roofing changes.
Two slope rules people confuse with this one
The ice barrier requirement is a separate rule with separate geometry. It is triggered by climate history rather than by slope, and it is measured horizontally from the eave to a point 24 inches inside the exterior wall line. Slope changes how far up the roof that horizontal distance lands, but it does not change the requirement itself. Our guide to ice dam protection membrane code requirements works through that coverage calculation in full.
The second is the reroofing exception in IRC R908.1. Reroofing is not required to meet the 1/4:12 minimum design slope in Section R905 for roofs that already provide positive roof drainage. That exception applies to the low slope design slope minimum, not to the 2:12 shingle floor or the double underlayment band. A 1.5:12 shingle roof does not become compliant because it is a tear off. For those assemblies, see the low slope roofing guide.
What inspectors actually write up
Four underlayment errors on 2:12 to 4:12 sections break a specific line of Table R905.1.1(2) or an evaluation report, and all four are visible from a ladder before the shingles go on. Ask for the underlayment inspection before the roof is covered.
- Starter strip placed above the eave instead of at it. The 19 inch strip starts at the eave, and the first 36 inch sheet starts there too.
- Single layer carried across a slope transition. A dormer or porch that drops to 3:12 needs the double layer even when the main field is 8:12.
- Felt lap dimensions applied to a synthetic product. The evaluation report governs: ESR-2945 measures the low slope lap to the centerline of the course below, 24 inches on a 48 inch roll.
- Wrinkled underlayment. The code language on distortions interfering with the ability of the shingles to seal is enforceable, not advisory.
Frequently asked questions
For roof slopes from 2:12 to 4:12, how many layers of underlayment are required?
Two layers. IRC R905.2.2 requires double underlayment on asphalt shingle roofs from 2:12 up to 4:12, applied per IRC Table R905.1.1(2): a 19 inch strip at the eave, then 36 inch sheets overlapping 19 inches, with 4 inch end laps offset 6 feet. One layer of ASTM D1970 self-adhering membrane is the permitted alternative under R905.1.1 Exception 1.
What does IRC R905.1.1 require?
IRC R905.1.1 requires underlayment under asphalt shingles, tile, metal shingles, roll roofing, slate, wood and metal panels to meet the ASTM types in Table R905.1.1(1), be applied per Table R905.1.1(2) and be attached per Table R905.1.1(3). Underlayment must bear a label showing compliance with ASTM D226, D1970, D4869 or D6757 as applicable.
What roof slope requires double underlayment?
Under IRC R905.2.2, asphalt shingle roofs from 2:12 up to but not including 4:12 require a double underlayment application. Clay and concrete tile carries the same requirement from 2 1/2:12 up to 4:12 under R905.3.2. At 4:12 and above, both coverings may use a single layer. The method for both is prescribed in Table R905.1.1(2).
What is the minimum roof slope for asphalt shingles?
IRC Section R905.2.2 sets 2 units vertical in 12 units horizontal, a 17 percent or 9.5 degree slope, as the minimum for asphalt shingles. There is no exception that lets shingles go lower, and no underlayment upgrade substitutes for the slope. Below 2:12 the assembly has to switch to a low slope covering such as modified bitumen, TPO, EPDM, or a standing seam metal panel.
How do you install double underlayment on a low slope roof?
Per IRC Table R905.1.1(2), apply a 19 inch strip of underlayment felt parallel to and starting at the eaves. Starting at the eave again, apply 36 inch wide sheets, overlapping each successive sheet 19 inches, working up the slope in shingle fashion. That leaves 17 inches of exposure per course. Keep the sheets flat and offset end laps by 6 feet.
Does synthetic underlayment need two layers below 4:12?
Yes, but the laps come from the product’s ICC-ES evaluation report rather than the felt table. ESR-2945 for Grip-Rite ShingleLayment and ESR-5197 for Fast Layment both require the underlayment to be lapped to the centerline of the underlying course, forming two layers with 6 inch end laps, for slopes from 2:12 up to 4:12 under asphalt shingles.
What is the minimum slope for a metal roof?
IRC R905.10.2 splits metal roof panels by seam type: 3:12 for lapped, nonsoldered seams without applied lap sealant, 1/2:12 for the same seams with sealant, and 1/4:12 for standing seam systems. Metal roof shingles are a separate product under R905.4.2 with a 3:12 minimum. Standing seam therefore has the lowest slope floor of any steep slope metal option.
Do underlayment lap requirements change in high wind areas?
Yes. In the 2021 IRC, where Figure R301.2.1.1 requires wind design, Table R905.1.1(2) requires two layers of underlayment at every slope for asphalt shingles and tile, using the 19 inch method with 4 inch end laps offset 6 feet, and Table R905.1.1(3) requires cap nails on a 12 inch grid. Metal shingles, slate, wood and metal panels also take the two layer method there. The 140 mph, 4 inch lap rule is the IBC Table 1507.1.1(2) wording for commercial buildings.
Does the reroofing exception let me keep a low slope shingle roof?
No. IRC R908.1 exempts reroofing from the 1/4:12 minimum design slope in Section R905 where the roof provides positive drainage. That exception addresses low slope membrane drainage, not the 2:12 shingle minimum or the double underlayment band. A shingle roof below 2:12 does not become compliant at tear off, and one at 3:12 still needs two layers of underlayment.
The Roofing Brief cites the 2021 International Residential Code and current ICC-ES evaluation reports. Adopted code editions and amendments vary by jurisdiction. Confirm requirements with your local building department before submitting for permit.