By The Roofing Brief Team. Last reviewed: November 2026.
Correction, November 14, 2026: an attribution or figure in an earlier version did not match its cited source and has been corrected after a source check.
Roof and siding replacement cost for a 2,000 sq ft house runs about $13,000 to $45,000 in 2026 with architectural asphalt shingles and vinyl or fiber cement siding, before removal and permit fees. That range applies Fixr’s 2026 per-square-foot siding prices and The Roofing Brief’s $5 to $8 per sq ft shingle baseline to measured roof and wall area, and the midpoints land between about $24,900 and $33,000.
Story count decides which half of the bill is bigger. At a 6/12 pitch, a one-story 2,000 sq ft house carries about 2,442 sq ft of roof and 1,800 sq ft of net wall, while a two-story house of the same floor area carries about 1,268 sq ft of roof and 2,216 sq ft of net wall. The tables below show that arithmetic line by line, so a homeowner can swap in their own measurements and contractor rates.
Key numbers at a glance
These seven figures answer most new roof and siding cost questions. Each one carries its source and date, and the house-size figures use the same 40 x 50 ft one-story and 25 x 40 ft two-story footprints as our 2,000 sq ft roof cost breakdown.
| Figure | Value | Source |
|---|---|---|
| Architectural asphalt shingles, installed | $5 to $8 per sq ft of roof | The Roofing Brief 2026 Roofing Cost Report |
| Vinyl siding, installed | $3 to $12 per sq ft of wall | Fixr siding replacement cost, updated Jan 23, 2026 |
| Fiber cement siding, installed | $5 to $14 per sq ft of wall | Fixr, Jan 23, 2026 |
| Siding for a 2,000 sq ft house | $14,500 average; 1,800 to 2,000 sq ft of siding needed | Fixr, Jan 23, 2026 |
| Roof area, 2,000 sq ft house at 6/12 | 2,442 sq ft (one story) or 1,268 sq ft (two story) | Roofing Brief calculation, IKO pitch factor 1.118 |
| Resale value recouped, national | Fiber cement siding 113.7%, vinyl siding 96.5%, asphalt roof 67.5% | 2025 Cost vs. Value Report |
| Sourced savings from bundling both jobs | About $549 to $1,049 | Roofing Brief estimate (arithmetic below) |
How much does a new roof and siding cost together?
A new roof and siding cost about $17,600 to $41,100 on a one-story 2,000 sq ft house and about $13,000 to $36,700 on a two-story house, using architectural shingles and vinyl siding. Fiber cement siding raises the range by $3,600 on the one-story house and $4,432 on the two-story, because Fixr prices it $2 per sq ft higher than vinyl at both the low and high end.
The table multiplies each per-square-foot range by the roof area or net wall area of each house. The midpoint column uses the middle of each sourced range ($6.50 roof, $7.50 vinyl, $9.50 fiber cement, $6 engineered wood) and is a Roofing Brief estimate, not a quoted price.
| House and materials | Roof cost | Siding cost | Combined range | Midpoint estimate |
|---|---|---|---|---|
| One story, architectural + vinyl | $12,210 to $19,536 | $5,400 to $21,600 | $17,610 to $41,136 | $29,373 |
| One story, architectural + fiber cement | $12,210 to $19,536 | $9,000 to $25,200 | $21,210 to $44,736 | $32,973 |
| One story, architectural + engineered wood | $12,210 to $19,536 | $3,600 to $18,000 | $15,810 to $37,536 | $26,673 |
| Two story, architectural + vinyl | $6,340 to $10,144 | $6,648 to $26,592 | $12,988 to $36,736 | $24,862 |
| Two story, architectural + fiber cement | $6,340 to $10,144 | $11,080 to $31,024 | $17,420 to $41,168 | $29,294 |
| Two story, architectural + engineered wood | $6,340 to $10,144 | $4,432 to $22,160 | $10,772 to $32,304 | $21,538 |
Source note: roof rates from the 2026 Roofing Cost Report; siding rates from Fixr (Jan 23, 2026). Areas: one story 2,442 sq ft roof and 1,800 sq ft net wall; two story 1,268 sq ft roof and 2,216 sq ft net wall. Removal, permits, decking and trim are extra and are priced in the worked example further down.
Roof squares vs wall squares: the arithmetic for a 2,000 sq ft house
Roofers and siders both price by the square, 100 sq ft of surface, but they measure different surfaces. A roof square is measured on the sloped plane, so pitch and overhang add area; a siding square is measured on the walls, so ceiling height, gable triangles and window openings change the count. Floor area alone predicts neither.

- Roof footprint. Add a 1 ft overhang on every side: 42 x 52 ft = 2,184 sq ft for the one-story house, 27 x 42 ft = 1,134 sq ft for the two-story.
- Roof pitch. Multiply by IKO’s 6/12 area factor of 1.118: 2,442 sq ft (24.4 squares) and 1,268 sq ft (12.7 squares). An 8/12 roof uses 1.202 and a 12/12 roof uses 1.414.
- Wall rectangle. Multiply the perimeter by the sided height, assumed here at 9 ft per story: 180 ft x 9 ft = 1,620 sq ft, and 130 ft x 18 ft = 2,340 sq ft.
- Gable triangles. With gables on the short walls, each triangle is half the span times the rise: 2 x (0.5 x 40 x 10) = 400 sq ft, and 2 x (0.5 x 25 x 6.25) = 156 sq ft. A hip roof has no gable triangles.
- Openings. Subtract windows at 15 sq ft and doors at about 20 sq ft: 12 windows and 2 doors remove 220 sq ft; 16 windows and 2 doors remove 280 sq ft.
- Net wall. 2,020 minus 220 = 1,800 sq ft (18.0 squares); 2,496 minus 280 = 2,216 sq ft (22.2 squares). Siding crews then order about 10% extra for cuts, which puts the one-story order near 1,980 sq ft, inside Fixr’s 1,800 to 2,000 sq ft band.
| Measurement | One story, 40 x 50 ft | Two story, 25 x 40 ft | Basis |
|---|---|---|---|
| Roof area at 6/12 | 2,442 sq ft (24.4 squares) | 1,268 sq ft (12.7 squares) | Footprint plus 1 ft overhang x 1.118 (IKO) |
| Gross wall, rectangle | 1,620 sq ft | 2,340 sq ft | Perimeter x 9 ft per story |
| Gable triangles | 400 sq ft | 156 sq ft | 6/12 rise on the short walls |
| Openings deducted | 220 sq ft | 280 sq ft | 15 sq ft windows, 20 sq ft doors |
| Net wall to side | 1,800 sq ft (18.0 squares) | 2,216 sq ft (22.2 squares) | Roofing Brief calculation |
| Wall squares per roof square | 0.74 | 1.75 | Net wall divided by roof area |
The last row is the number most quotes hide. A two-story house has 1.75 squares of wall for every square of roof, so the siding line will usually be the larger half of the bill; a ranch has 0.74, so the roof usually dominates. For pitch factors from 4/12 to 12/12, see the table in our 2,000 sq ft roof cost by story and pitch guide.
Siding cost by material, with the maker specs that matter
Siding material moves the combined bill more than shingle choice does on a two-story house, because the wall area is 1.75 times the roof area. Fixr’s January 2026 ranges run from $2 per sq ft for engineered wood up to $16 per sq ft for steel, and each material has its own code standard and warranty structure.
| Siding | Installed cost per sq ft | 1,800 sq ft wall (one story) | 2,216 sq ft wall (two story) | Code standard or maker warranty | Source |
|---|---|---|---|---|---|
| Vinyl | $3 to $12 | $5,400 to $21,600 | $6,648 to $26,592 | Must be labeled to ASTM D3679 (IRC R703.11) | Fixr, Jan 2026; 2021 IRC |
| Fiber cement (James Hardie HardiePlank and others) | $5 to $14 | $9,000 to $25,200 | $11,080 to $31,024 | ASTM C1186 for lap up to 12 in wide (IRC R703.10.2); Hardie 30-year non-prorated, transferable substrate warranty; ColorPlus finish 15 years | Fixr; 2021 IRC; James Hardie |
| Engineered wood (LP SmartSide and others) | $2 to $10 | $3,600 to $18,000 | $4,432 to $22,160 | LP 5/50: 5 years of 100% labor and material, then 50-year prorated material | Fixr; LP Building Solutions |
| Aluminum | $3 to $10 | $5,400 to $18,000 | $6,648 to $22,160 | 0.019 in minimum (IRC Table R703.3(1)) | Fixr, Jan 2026 |
| Steel | $4 to $16 | $7,200 to $28,800 | $8,864 to $35,456 | 29 gauge minimum (IRC Table R703.3(1)) | Fixr, Jan 2026 |
| Wood | $2 to $15 | $3,600 to $27,000 | $4,432 to $33,240 | Repaint cycle drives lifetime cost | Fixr, Jan 2026 |
Fixr also lists $1 to $4 per sq ft for siding labor alone, $1,000 to $2,500 to remove and dispose of the old siding, and $150 to $1,500 in permit and inspection fees. Gauge, profile and panel options for steel and aluminum are covered in our metal siding guide.
Warranty structure matters when both jobs are bid together. James Hardie states its siding, trim and soffit substrate warranty is 30 years, non-prorated and transferable, while LP SmartSide pays 100% of labor and material only in the first 5 years. Ask each bidder which warranty document applies and whether their installer status affects it.
Roof cost by roof size, including the 1,000 and 2,200 sq ft questions
The roof half of the bill is roof area times the installed rate. At The Roofing Brief’s $5 to $8 per sq ft baseline for architectural shingles, 1,000 sq ft of roof (10 squares) costs about $5,000 to $8,000, and each additional 500 sq ft adds about $2,500 to $4,000. Fixr’s February 2026 size table is wider because it spans budget and premium materials.
| Roof area (not floor area) | Architectural asphalt at $5 to $8 | Fixr all-material range |
|---|---|---|
| 1,000 sq ft (10 squares) | $5,000 to $8,000 | $3,750 to $11,000 |
| 1,500 sq ft (15 squares) | $7,500 to $12,000 | $5,625 to $16,500 |
| 2,000 sq ft (20 squares) | $10,000 to $16,000 | $7,500 to $22,000 |
| 2,500 sq ft (25 squares) | $12,500 to $20,000 | $9,375 to $27,500 |
| 2,200 sq ft house, one story (2,677 sq ft roof) | $13,385 to $21,416 | Not listed |
| 2,200 sq ft house, two story (1,389 sq ft roof) | $6,945 to $11,112 | Not listed |
Source note: Fixr roof replacement cost, updated Feb 4, 2026. The 2,200 sq ft rows assume a 40 x 55 ft one-story or 25 x 44 ft two-story footprint, a 1 ft overhang and the 6/12 factor of 1.118. Fixr also prices tear-off at about $50 per square for asphalt, including dumping, and permits at $100 to $500. Material-by-material roof prices sit in our roof replacement cost guide, and the size trap behind small roofs is explained in our 1,000 sq ft roof cost guide.
Worked example: two-story 2,000 sq ft house, architectural shingles plus vinyl siding
A two-story 2,000 sq ft house with a new architectural shingle roof and new vinyl siding comes to about $14,900 to $41,900 including tear-off, siding removal and two permits, with a midpoint near $28,400. The siding line is about twice the roof line at the midpoint, $16,620 against $8,242, because the walls hold 22.2 squares and the roof holds 12.7.
| Line item | Quantity and rate | Low | Midpoint | High | Source |
|---|---|---|---|---|---|
| Architectural shingle roof, installed | 1,268 sq ft x $5 / $6.50 / $8 | $6,340 | $8,242 | $10,144 | 2026 Roofing Cost Report |
| Roof tear-off and dumping | 12.7 squares x $50 | $635 | $635 | $635 | Fixr roof replacement cost, Feb 2026 |
| Vinyl siding, installed | 2,216 sq ft x $3 / $7.50 / $12 | $6,648 | $16,620 | $26,592 | Fixr, Jan 2026 |
| Old siding removal and disposal | Whole house | $1,000 | $1,750 | $2,500 | Fixr, Jan 2026 |
| Roof permit | One permit | $100 | $300 | $500 | Fixr, Feb 2026 |
| Siding permit and inspection | One permit | $150 | $825 | $1,500 | Fixr, Jan 2026 |
| Total | $14,873 | $28,372 | $41,871 | Roofing Brief arithmetic |
Three costs sit outside this total. Rotted roof deck found at tear-off runs $2 to $5 per sq ft installed per HomeGuide’s roof decking cost guide, so replacing 10% of this deck (127 sq ft) would add about $254 to $635. Soffit, fascia and gutters are separate line items on many bids, so confirm in writing whether the 4/4 and 5/4 trim that the Cost vs. Value siding scope includes is in your quote. Wall sheathing damage behind old siding is priced per sheet once the walls are open.
Does replacing the roof and siding together save money?
Bundling saves a few hundred to about a thousand dollars in sourced costs, roughly 2% to 4% of the $28,372 midpoint, not the 10% to 20% some contractor pages claim without a source. The savings come from one disposal container, a possible shared permit and kickout flashing installed during the reroof instead of as a retrofit.
| Shared item | Separate jobs | One combined job | Possible saving | Source |
|---|---|---|---|---|
| Roll-off dumpster | 2 x 20 yd at $679 average = $1,358 | 1 x 30 yd at $809 average | $549 | Dumpsters.com national averages, as listed November 2026 |
| Permits | Roof $100 to $500 plus siding $150 to $1,500 | One building permit, only where the jurisdiction issues one for both scopes | $0 to $500 | Fixr roof and siding guides, 2026 |
| Kickout flashing, per location | $75 to $300 as a retrofit | $25 to $75 during a full reroof | $50 to $225 per location | Roofing Brief editorial planning ranges, kickout flashing guide |
| Sourced total | $549 to $1,049, plus any kickout saving | Roofing Brief estimate |
Two cautions apply to the dumpster line. Dumpsters.com lists ranges of $374 to $1,362 for a 20 yd and $450 to $1,460 for a 30 yd container, and 12.7 squares of shingles at the 235 lb per square minimum in the Cost vs. Value roofing spec weigh about 2,985 lb before underlayment and siding, so check the tonnage included. Where the roofer’s $50 per square tear-off price already includes dumping, the container saving shrinks to the siding crew’s share.
The larger payoff is technical, not financial. Step flashing, at least 4 x 4 in under 2021 IRC R905.2.8.3, sits behind the siding and cannot be inspected or replaced without removing the cladding, as our step flashing installation guide explains, so a reroof done two years before re-siding often means cutting back new siding or reusing old flashing.
Roof first or siding first? The flashing sequence
Roof first, then siding, is the standard order, because the siding and its water-resistive barrier must lap over the vertical legs of the step and kickout flashing that the roofer installs. 2021 IRC R905.2.8.3 sets sidewall base flashing at not less than 4 in high and 4 in wide, and R703.2 requires the wall barrier to be continuous and lapped at least 2 in horizontally.

- Tear off the roof and repair the deck. Replace soft sheathing before anything else goes on; Fixr’s tear-off figure of $50 per square covers asphalt removal and dumping.
- Install eave drip edge, underlayment, then rake drip edge. Drip edge goes under the underlayment at eaves and over it at rakes, and 2021 IRC R905.2.8.5 requires it on asphalt shingle roofs.
- Set the kickout first at each roof-to-wall eave. 2021 IRC R903.2.1 requires a flashing that diverts water where a sloped eave meets a sidewall; the PNNL Building America Solution Center shows the detail.
- Weave step flashing up the sidewall. One piece per shingle course, each at least 4 x 4 in, nailed on the roof leg only.
- Strip the walls and install the water-resistive barrier. R703.2 accepts No. 15 felt to ASTM D226 Type 1 or a wrap meeting ASTM E2556, lapped 2 in at horizontal seams and 6 in at vertical joints, and lapped over the flashing’s wall legs.
- Hang siding with the maker’s roof clearance. James Hardie’s HardiePlank instructions require a gap between the roof surface and the bottom of the siding (a 1 in minimum in the FL13192 edition; other editions call for 1 to 2 in), so read the edition the installer is using.
- Hang gutters last. The gutter end must sit clear of the wall so the kickout can discharge into it.
| Code section (2021 IRC) | What it requires | Which crew owns it on a combined job |
|---|---|---|
| R903.2.1 | Flashing at wall and roof intersections, plus a diverter where a sloped eave meets a sidewall; metal not less than 0.019 in (No. 26 galvanized) | Roofer |
| R905.2.8.3 | Sidewall base flashing, continuous or step, not less than 4 in high and 4 in wide | Roofer, with siding lapped over it |
| R703.2 | At least one continuous water-resistive barrier behind the siding, lapped 2 in horizontal and 6 in at joints | Siding crew |
| R703.4 | Approved corrosion-resistant flashing applied shingle-fashion to keep water out of the wall cavity and framing | Siding crew |
| R703.11 | Vinyl siding labeled to ASTM D3679 and installed to the maker’s instructions | Siding crew |
| R703.10.2 | Fiber cement lap siding up to 12 in wide meets ASTM C1186 | Siding crew |
Code text from the 2021 IRC Chapter 7 and Chapter 9; local amendments can change these sections, so ask the building department which edition applies before the two crews are scheduled.
Is it more expensive to replace siding or a roof?
Per square foot, siding often costs more than an asphalt roof: the 2025 Cost vs. Value Report’s vinyl siding project works out to $14.36 per sq ft and its asphalt roof to $10.62 per sq ft. Per house, the answer flips with story count, since a two-story house has 1.75 times more wall than roof and a ranch has only 0.74 times.
| 2025 Cost vs. Value project (national) | Scope | Job cost | Implied cost per sq ft | Resale value | Cost recouped |
|---|---|---|---|---|---|
| Siding replacement, vinyl | 1,250 sq ft, factory trim, housewrap | $17,950 | $14.36 | $17,313 | 96.5% |
| Siding replacement, fiber cement | 1,250 sq ft, factory primed and painted, 4/4 and 5/4 trim | $21,485 | $17.19 | $24,420 | 113.7% |
| Roofing replacement, asphalt | 30 squares, min. 235 lb shingles, tear-off to sheathing | $31,871 | $10.62 | $21,501 | 67.5% |
| Roofing replacement, metal | 30 squares | $51,865 | $17.29 | $25,972 | 50.1% |
Source: Zonda’s 2025 Cost vs. Value Report on JLC Online. Implied cost per sq ft is job cost divided by project area (Roofing Brief arithmetic). Cost vs. Value prices a full-service remodeler job, so its rates sit above the Fixr and Roofing Brief baselines used earlier.
Applied to the two-story example, the remodeler-benchmark rates give $13,466 for the roof (1,268 x $10.62) and $31,822 for vinyl siding (2,216 x $14.36), a $45,288 total. Paired as Cost vs. Value prices them, asphalt roof plus fiber cement siding costs $53,356 and returns $45,921 at resale (86.1%), while asphalt plus vinyl costs $49,821 and returns $38,814 (77.9%). Those combined percentages are our arithmetic; the report scores each project separately. The full roofing resale picture is in our roof replacement ROI report.
Insurance: when a hail claim pays for both
A single hail or wind storm that damages both roof and siding is one loss, and the standard ISO HO 00 03 homeowners form applies one deductible to all covered damage from that loss. Whether undamaged walls get re-sided to match depends on state rules: Florida Statute 626.9744 and Ohio Adm. Code 3901-1-54 set matching standards, and most other states rely on policy wording.
| Rule | Matching standard | Source |
|---|---|---|
| NAIC model regulation | Replace all items in the area for “a reasonably uniform appearance” when replacements do not match; binding only where adopted | NAIC Model 902, Section 9.A(2) |
| Florida | Insurer “shall make reasonable repairs or replacement of items in adjoining areas”; may weigh cost, uniformity and remaining useful life | Fla. Stat. 626.9744(2) |
| Ohio | Replace enough of the item for a “reasonably comparable appearance” | Ohio Adm. Code 3901-1-54 |
| States without a rule | “Like kind and quality” policy wording and case law decide | Your state insurance department |
Before the adjuster visits, pull one damaged siding panel and photograph the maker’s stamp on its back, then ask in writing whether that color and profile are still made. Lab tests summarized in our hail damage to a house guide found new vinyl siding cracking from hail of 0.75 to 1.25 in, so a storm that bruised shingles may have cracked siding too.
Paying for a $13,000 to $45,000 exterior project
A combined roof and siding job is often too large for a credit card and small enough for a home equity loan, a HELOC or a personal loan. For buyers or refinancers, HUD’s Limited 203(k) program allows up to $75,000 of repairs under Mortgagee Letter 2024-13, for FHA case numbers assigned on or after November 4, 2024.
Federal energy credits do not cut this bill: asphalt and metal roofs stopped qualifying under 25C after 2022, and Public Law 119-21 ended the 25C credit for property placed in service after December 31, 2025. Rates, approval odds and contractor-financing clauses are compared in our roof financing options guide.
Which roof and siding combination should you pick?
The cheapest combined bill on a two-story house comes from controlling the siding line, while on a ranch it comes from the roof line. Use the thresholds below with your own wall-to-roof ratio, which is 1.75 on the two-story example and 0.74 on the ranch.
| If your situation is | Then | Why (with the number) |
|---|---|---|
| Two-story house, wall-to-roof ratio above 1.5 | Spend on siding grade, keep architectural shingles | Each $1 per sq ft of siding costs $2,216 on the example house; each $1 per sq ft of roof costs $1,268 |
| Ranch, wall-to-roof ratio below 1.0 | Spend on the roof, keep a mid-grade vinyl | Each $1 per sq ft of roof costs $2,442; each $1 per sq ft of siding costs $1,800 |
| Selling within about 5 years | Fiber cement over vinyl if the budget allows | 113.7% vs 96.5% recouped in the 2025 Cost vs. Value Report |
| Hail-prone area with a pending claim | File once for both, before signing separate contracts | One deductible per loss under ISO HO 00 03 |
| Roof under 10 years old, siding failing | Re-side only; have the siding crew replace or reuse the step flashing and add kickouts | Kickout retrofit $75 to $300 per location (Roofing Brief planning range) |
| Siding under 10 years old, roof failing | Reroof only; specify the existing siding be cut back for new step flashing | R905.2.8.3 needs 4 x 4 in flashing under the siding |
| Bids differ by more than 20% | Compare roof area and net wall area on each bid before price | A 10% area difference on 2,216 sq ft is 222 sq ft of siding |
Ask every bidder for four numbers in writing: roof squares, wall squares net of openings, the price per square for each, and who owns the step and kickout flashing. A bid that gives only a lump sum cannot be checked: a 10% gap in measured roof area on a 24.4-square ranch is 244 sq ft, or about $1,220 to $1,952 at $5 to $8 per sq ft.
Frequently asked questions
How much does it cost to put siding on a 2000 sq ft house?
Fixr’s January 2026 data puts siding on a 2,000 sq ft house at a $14,500 average, with about 1,800 to 2,000 sq ft of siding needed. At Fixr’s vinyl rate of $3 to $12 per sq ft, a one-story house with 1,800 sq ft of net wall costs $5,400 to $21,600, and a two-story house with 2,216 sq ft costs $6,648 to $26,592.
Is it more expensive to replace siding or a roof?
Per square foot, siding often costs more: the 2025 Cost vs. Value Report implies $14.36 per sq ft for vinyl siding and $10.62 for an asphalt roof. Per house, a two-story home has about 1.75 sq ft of wall per sq ft of roof, so siding usually costs more; a ranch has about 0.74, so the roof usually costs more.
How much does it cost to replace a roof on a 2,200 square-foot house?
A one-story 2,200 sq ft house with a 6/12 roof and 1 ft overhangs has about 2,677 sq ft of roof, which costs about $13,385 to $21,416 in architectural shingles at $5 to $8 per sq ft. A two-story house of the same floor area has about 1,389 sq ft of roof and costs about $6,945 to $11,112.
How much does it cost to replace a 1,000 sq foot roof?
A roof with 1,000 sq ft of surface, which is 10 squares, costs about $5,000 to $8,000 in architectural asphalt shingles at The Roofing Brief’s 2026 baseline of $5 to $8 per sq ft. Fixr’s February 2026 all-material range for the same size is $3,750 to $11,000, and tear-off adds about $500 at $50 per square.
What is the roof and siding replacement cost per square foot?
Architectural shingles run $5 to $8 per sq ft of roof, vinyl siding $3 to $12 and fiber cement $5 to $14 per sq ft of wall, per the 2026 Roofing Cost Report and Fixr. Because roof and wall areas differ, price each surface separately; a single per-square-foot figure for the whole house hides which half drives the bill.
Should the roof or the siding be replaced first?
Replace the roof first. The roofer installs step flashing at least 4 by 4 inches under 2021 IRC R905.2.8.3 and a kickout diverter under R903.2.1, and the siding crew then laps the water-resistive barrier and siding over those flashing legs. Reversing the order usually means cutting back new siding to reach the flashing.
Sources
- Fixr, How Much Does It Cost to Replace Siding? (updated January 23, 2026)
- Fixr, Roof Replacement Cost (updated February 4, 2026)
- Zonda, 2025 Cost vs. Value Report, national averages
- IKO, Estimating How Much Roofing Is Required (pitch factors)
- 2021 International Residential Code, Chapter 7 and Chapter 9
- James Hardie, warranty statement and HardiePlank installation instructions (FL13192)
- LP Building Solutions, LP SmartSide 5/50 Limited Warranty
- Dumpsters.com, roll-off dumpster prices (as listed November 2026)
- PNNL Building America Solution Center, step and kick-out flashing
- Florida Statutes 626.9744; Ohio Adm. Code 3901-1-54; NAIC Model 902
- HUD, FHA INFO 2024-44 (Limited 203(k) changes)