By The Roofing Brief Team | Last reviewed: November 2026
Downspout repair is mostly a mechanical fix: a leaking joint, a downspout that swings or falls off, or a crushed section is usually solved by re-seating the parts crimped end down, adding screws and straps, or swapping one 10 ft section, not by caulking over the problem. Amerimax's metal gutter instructions join every downspout and elbow larger end over smaller end, secure them with sheet metal screws and fasten the run with 2 bands per 10 ft section.
Most downspout gutter repair jobs land in one of five buckets: a dripping joint, a loose or fallen run, a dent, a clog, or water dumped too close to the foundation. A pro replaces or adds one downspout for $30 to $75, per HomeGuide's downspout cost guide, and the parts for a one-section DIY swap cost about $35 on November 2026 Home Depot listings. For gutter troughs, hangers and seams rather than the downspout, see our guide to gutter repair services and what they fix.
Key numbers at a glance
| Item | Number | Source |
|---|---|---|
| Straps per 10 ft section | 2 bands (metal) or 2 clips (vinyl) | Amerimax metal guide; Amerimax vinyl guide |
| Strap position on a 10 ft run | About 1 ft from the top and 1 ft from the bottom | K&M Sheet Metal |
| Joint direction | Crimped (smaller) end points down into the larger end below | Amerimax metal guide |
| Joint fastener | 1/2 in self-tapping, rust-resistant screw | Amerimax vinyl guide |
| Gutter sealant cure | Geocel 2320: tack-free 15 min, cure 5 days. OSI GS121: skin 30 min, cure 7 to 14 days | Geocel 2320/2321 data sheet; OSI GS121 data sheet |
| Pro price, one downspout | $30 to $75 | HomeGuide |
| Discharge distance | At least 5 ft from the foundation (10 ft for an underground catchment) | DOE Building America Solution Center |
Which downspout repair do you need? Match the symptom to the fix
Read the symptom before buying parts. A drip at one joint points to a crimp installed upside down or a missing screw; a run that rattles or leans points to failed straps; water pouring over the gutter while the downspout stays dry points to a clog at the top elbow. Running a garden hose into the gutter at the outlet for 2 to 3 minutes shows which of these you have.
| Symptom | Most likely cause | Fix | Parts |
|---|---|---|---|
| Drips or sprays at a joint during rain | Crimped end points up, or the joint slid apart | Re-seat crimp-down, one 1/2 in screw per side | 2 zip screws |
| Leak where the top elbow meets the gutter | Elbow slipped off the outlet tube, or the outlet flange seal failed | Re-seat the elbow and screw it; reseal the outlet flange inside the gutter | Screws, gutter sealant |
| Downspout swings or bangs in wind | Straps pulled out of siding or missing | Re-strap at 2 per 10 ft into framing or masonry | Bands, longer wall screws |
| Downspout fell off the house | Ice or snow load, ladder strike, screws pulled from the outlet | Reattach at the outlet, replace a torn outlet, re-strap | Outlet, 1/8 in aluminum rivets, bands |
| Crushed or dented section | Mower, ladder or impact | Reshape if the hose test flows full; otherwise replace the section | 10 ft section |
| Split seam or rust-through | Water froze in a clogged pipe, or corrosion on steel | Replace the section or elbow | Section or elbow |
| Gutter overflows at the outlet, downspout trickles | Clog at the top elbow | Clear from the top, then snake | None |
| Water pools at the base of the wall | Discharge under 5 ft from the foundation | Add an extension or splash block | Extension |
How to fix a leaking downspout joint or elbow
A leaking downspout joint is fixed by taking it apart and reassembling it crimped end down with a 1/2 in screw on each side, because a joint with the crimp pointing up sends water out the seam on every storm. Amerimax states that each downspout and elbow has one crimped end and that parts join by fitting the larger end of one over the smaller end of the other. Sealant comes last, only if a correctly assembled joint still drips.

- Run a hose into the gutter at the outlet for 2 to 3 minutes and mark each drip with painter's tape.
- Back out the screws at the leaking joint with a 1/4 in nut driver and pull the two pieces apart.
- Check the crimp: the smaller, crimped end must point down into the larger end below it. If it points up, flip the piece, or cut off the old crimp and re-crimp the other end with a 5-blade crimper such as the Malco C5R. Our guide on how to cut a gutter downspout covers clean cuts and crimping by material.
- Push the joint fully home and drive one 1/2 in self-tapping, rust-resistant screw on each side face, the fastener Amerimax's vinyl gutter instructions specify at the outlet elbow. This Old House recommends short aluminum pan-head screws here and notes that the shorter the screw, the better, because long tips snag leaves inside the pipe.
- Hose-test again. If the reassembled joint still weeps, dry the metal and run a bead of gutter sealant around the outside of the lap, tooled flat and no larger than 1/4 x 1/4 in for Geocel 2320, the limit on its data sheet.
- Wait for the sealant to skin before rain or a retest: 15 minutes tack-free for Geocel 2320, about 30 minutes for OSI GS121 at 72°F and 70% relative humidity, per their data sheets. Do not apply OSI GS121 below 40°F.
A leak at the very top, where the elbow meets the gutter outlet, has two sources. If water runs down the outside of the elbow, the outlet tube is not inside the elbow and needs re-seating and screwing. If water drips from under the gutter around the outlet, the outlet flange seal inside the trough has failed and needs a bead of gutter sealant applied from inside the gutter, around the 2×3 or 3×4 in opening.
Gutter sealants for downspout joints compared
| Product | Rated for | Tack-free or skin | Full cure | Joint limits | Paint | Source |
|---|---|---|---|---|---|---|
| Geocel 2320/2321 Gutter and Narrow Seam Sealant | Aluminum, galvanized and vinyl-clad gutters, end caps and downspouts | 15 min | 5 days | Do not use on joints larger than 1/4 x 1/4 in | After 24 hours with latex or most oil-based paints | Geocel data sheet |
| OSI GS121 Gutter Sealant | Aluminum, galvanized steel and vinyl gutters and downspouts; not copper | 30 min skin at 72°F, 70% RH | 7 to 14 days | Backer material for joints deeper than 3/8 in; apply between 40°F and 120°F | After full cure | OSI data sheet |
| Geocel 2300 Construction Tripolymer | General construction joints with movement | 45 min | 4 days | Minimum 1/4 x 1/4 in, maximum 1/2 x 3/8 in | After 24 hours; 4 days for inflexible paints | Geocel data sheet |
For a downspout lap, the gutter-specific Geocel 2320 fits best because a lap seam is a narrow joint, inside the 1/4 x 1/4 in limit on its data sheet. OSI's GS121 sheet excludes copper, so a copper downspout needs a product whose data sheet lists copper. Neither sealant fixes a joint assembled crimp-up: water running down the inside face exits at the seam with enough volume to undercut a thin bead.
My gutter downspout fell off: how to put it back
A downspout that fell off usually lost its grip in one of two places: the top elbow slid off the gutter outlet tube, or the wall straps pulled out of the siding. Snow and ice loads cause both, because a 10 ft run packed with ice weighs far more than the empty 0.019 in aluminum pipe. Reattach it from the top down: outlet, elbows, sections, then straps.
- Inspect the gutter outlet. If the outlet tube is still attached and round, keep it. If it tore out of the gutter or is crushed, replace the outlet; on an aluminum gutter, fasten a new outlet flange with 1/8 in aluminum pop rivets (the rivet size This Old House lists for gutter work) and seal the flange from inside the trough. On Amerimax vinyl systems, the instructions say not to put screws through the drop outlet into the gutter.
- Straighten bent elbows only if they still close fully over the pipe; a 2×3 aluminum A elbow was listed at $2.80 to $3.44 on Home Depot in November 2026 depending on color, for example the Amerimax 3AE80W in High Gloss 80 White.
- Slide the top elbow over the outlet tube and drive one 1/2 in self-tapping screw on each side.
- Reassemble the offset and vertical run with every crimped end pointing down, one screw per side at each joint.
- Fasten 2 bands per 10 ft section, the first about 1 ft below the top and the last about 1 ft above the bottom. Drive the band screws into studs, blocking or masonry anchors, not vinyl or fiber-cement siding alone.
- Finish with a bottom elbow 6 to 12 in above the ground, the height Amerimax's vinyl instructions use, and an extension that carries water at least 5 ft from the foundation.
How many downspout straps a run needs
| Run height | Bands at 2 per 10 ft (Amerimax) | K&M Sheet Metal placement | Band cost at $1.98 each |
|---|---|---|---|
| 10 ft (one story) | 2 | 1 ft from top, 1 ft from bottom | $3.96 |
| 20 ft (two stories) | 4 | 3 usually sufficient on a straight run, one at the joint | $5.94 to $7.92 |
| 30 ft (three stories) | 6 | Not stated | $11.88 |
Band prices use a Home Depot listing for an Amerimax aluminum downspout band at $1.98, which fits 2×3 and 3×4 aluminum downspouts, as listed in November 2026; color and store stock change the price. K&M Sheet Metal notes that a strap at the joint of a 20 ft run also hides the seam, so it looks like one continuous length.
How to fix a crushed or dented downspout
A crushed or dented downspout can stay if a hose test at full flow clears it without backing up; if water backs up at the dent, or the metal is split or folded at a crease, replace the section. Standard 2×3 aluminum downspouts are made from 0.019 in material, per the Lynch Aluminum specification sheet, so they dent at ground level from mowers, bikes and ladder feet.
- Shallow dent, no crease: slide a 24 in length of 2×2 lumber or a broom handle inside from the open end and press the face back out, or pry a crushed opening gently with the flat tip of a pry bar, working in small steps.
- Sharp crease or split: replace the section. Re-bending a creased fold in 0.019 in aluminum can crack it at the fold line.
- Crushed bottom elbow: replace the elbow; at $2.80 to $3.44 for a 2×3 aluminum A elbow on November 2026 Home Depot listings, it is the cheapest part in the run.
- Repeated mower damage: swap the fixed extension for a hinged one such as the Amerimax Clip-Up, which the vinyl instructions list as part 18 and hold upright with 1 clip on the downspout.
How to replace a section of a downspout
To replace a section of a downspout, match the profile (2×3 or 3×4 in), material and color, remove the damaged piece between its joints, and cut new stock to the gap plus the overlap at each end. Most stock comes in 10 ft lengths; Lynch also sells 8 and 11 ft lengths in 2×3 and 3×4. A 10 ft 2×3 Amerimax white aluminum heavy-duty downspout was listed at $24.52 on Home Depot in November 2026.

| Profile | Cross-section | Roof area per downspout at 1 sq in per 100 sq ft | Aluminum wall (Lynch) | Lynch stock lengths |
|---|---|---|---|---|
| 2×3 in rectangular | 6 sq in | About 600 sq ft | 0.019 in | 8, 10 and 11 ft |
| 3×4 in rectangular | 12 sq in | About 1,200 sq ft | 0.019 or 0.024 in | 8, 10 and 11 ft |
| 4×5 in rectangular | 20 sq in | About 2,000 sq ft | 0.027 in | 10 ft |
The roof-area column applies the DOE Building America Solution Center rule of 1 square inch of downspout cross-section per 100 square feet of roof, so 2×3 x 100 = 600 sq ft. If the damaged downspout drains more than about 600 sq ft of roof and clogs or overflows often, a repair is the moment to move that drop to 3×4, which needs a matching 3×4 outlet and elbows. Our downspout spacing and sizing guide works through the full count.
- Measure the outside faces of the old pipe (2 x 3 in or 3 x 4 in), note the material (aluminum, galvanized steel, vinyl or copper) and the color name, and check which way each elbow turns.
- Remove the screws above and below the damaged piece and the bands holding it, then lift it out.
- Measure the gap between the pieces that stay, then add the overlap at each end. For example, a 72 in gap with 1-1/2 in of overlap at the top and bottom needs a 75 in cut.
- Cut the new stock square with a fine-tooth hacksaw (32 TPI, a 1/32 in tooth pitch) or double-cut downspout snips. Keep the factory crimp on the bottom end; if you cut it off, re-crimp the new bottom end.
- Install crimp-down, drive one 1/2 in screw per side at each joint, and re-band at 2 per 10 ft.
- Hose-test for 2 to 3 minutes at the outlet before putting the ladder away.
Elbows come in two orientations: an A elbow turns water out from the wall toward you, and a B elbow turns it left or right along the wall. Lynch makes its 2×3 A and B elbows from the same 0.019 in aluminum as the pipe. Buy the same letter as the one you remove; our explainer on A vs B gutter elbows shows how to tell them apart. For a full new run from outlet to extension, follow the downspout installation steps.
Clogged downspouts and underground drain lines
A clog is a repair problem when water overflows the gutter at the outlet while the downspout runs dry, or when a joint bursts after water froze inside a blocked pipe. Clear the top elbow from the gutter side first, then flush from the top with a hose for 2 to 3 minutes, and only seal joints after flow is restored. Our step-by-step on how to clean gutter downspouts covers each clog location.
A packed elbow mid-run usually needs a flexible auger; our guide to the gutter snake for unclogging a downspout compares the types. Where the downspout feeds a buried pipe, the DOE Building America Solution Center specifies non-perforated pipe sloped away from the house and warns against tying gutter drains into a perforated foundation drain. For a buried line that backs up at the downspout, use the method table in clearing a clogged underground gutter drain.
How much does downspout repair cost?
Downspout repair costs $30 to $75 per downspout when a pro replaces or adds one, per HomeGuide, while hourly handyperson rates for a leaking or swinging downspout run $37 to $68, per Fixr's downspout cost guide updated January 31, 2025. DIY parts for a typical fix cost $4 to $40 on November 2026 Home Depot listings. Two-story access and buried drain lines push the price up.
| Item | Price | Source and date |
|---|---|---|
| Pro: replace or add one downspout | $30 to $75 | HomeGuide downspout cost guide |
| Handyperson, leaking or swinging downspout | $37 to $68 per hour | Fixr, updated Jan 31, 2025 |
| Downspout extension (part) | $2 to $17 | Fixr, updated Jan 31, 2025 |
| 2×3 aluminum A elbow (Amerimax) | $2.80 to $3.44 by color | Home Depot listings, Nov 2026 |
| 10 ft 2×3 white aluminum heavy-duty downspout (Amerimax 24019010120) | $24.52 | Home Depot listing, Nov 2026 |
| Aluminum downspout band | $1.98 | Home Depot listing, Nov 2026 |
| OSI GS121 10 oz gutter sealant, 12-pack | $87.28 to $96.98 (about $7.27 to $8.08 per tube) | Home Depot listings, Nov 2026 |
| General gutter repair, whole system (for scale) | $195 to $625 | This Old House, citing HomeAdvisor |
Worked example: DIY parts for three common repairs
| Repair | Parts and arithmetic | Parts total (Roofing Brief estimate) |
|---|---|---|
| Replace one crushed 10 ft section with two new A elbows and 2 bands | $24.52 + (2 x $3.44) + (2 x $1.98) = $24.52 + $6.88 + $3.96 | $35.36 |
| Re-strap a fallen 20 ft two-story run at 2 per 10 ft | 4 x $1.98 | $7.92 |
| Reseal one outlet flange and two joints | 1 tube of OSI GS121 at $7.27 to $8.08 (from the 12-pack price) | $7.27 to $8.08 |
Those parts totals exclude screws, tax and a ladder. Against HomeGuide's $30 to $75 per-downspout pro range, the DIY saving on a one-story section swap is modest, so hiring is reasonable for two-story runs or anything above ladder height you are not set up for. For full-system pricing by problem and material, see our gutter repair cost breakdown.
Downspout repair or replacement: the decision table
Repair the joint, strap or single section when the rest of the run is sound, and replace the whole downspout when damage repeats across several sections or a 2×3 profile drains more than about 600 sq ft of roof. The thresholds below come from the maker instructions, data sheets and DOE guidance cited above.
| If your downspout | Then | Why |
|---|---|---|
| Drips at one joint and the metal is sound | Re-seat crimp-down and add a 1/2 in screw per side; seal only if it still drips | Amerimax joins parts larger end over crimped end with screws |
| Has a split seam, rust-through or a creased fold | Replace that section or elbow | Sealant joint limits are 1/4 x 1/4 in (Geocel 2320) |
| Has a shallow dent but the hose test flows full | Reshape it or leave it | Flow, not looks, decides |
| Fell off after snow or ice | Reattach at the outlet, replace a torn outlet, re-strap at 2 per 10 ft into framing | Strap pull-out from siding is the usual failure |
| Clogs or overflows every storm and drains over 600 sq ft of roof | Upsize that drop from 2×3 to 3×4 | DOE rule: 1 sq in of downspout per 100 sq ft of roof |
| Dumps water within 5 ft of the foundation | Add an extension; see our downspout extension options | DOE BASC 5 ft; 2021 IRC R801.3 requires 5 ft where expansive or collapsible soils exist |
| Is copper | Use a sealant whose data sheet lists copper | OSI GS121 excludes copper |
| Needs work above a one-story ladder | Hire it out or set the ladder at a 4-to-1 angle | OSHA 1926.1053(b)(5)(i): base out 1/4 of the working length |
Grade matters as much as hardware: the 2021 IRC R401.3 requires the ground to fall at least 6 in within the first 10 ft from the foundation, so an extension that empties onto a flat or back-sloped patch still sends water toward the wall.
Frequently asked questions
How much does it cost to repair a downspout?
Downspout repair costs $30 to $75 per downspout when a pro replaces or adds one, per HomeGuide, and a handyperson bills $37 to $68 an hour for a leaking or swinging downspout, per Fixr’s January 2025 guide. Doing it yourself, a 10 ft 2×3 aluminum section, two elbows and two bands came to about $35 in parts on Home Depot listings checked in November 2026.
How to fix a damaged downspout?
Fix a damaged downspout by matching the repair to the damage. Re-seat a leaking joint so the crimped end points down and add a 1/2 in screw on each side. Re-strap a loose run at 2 bands per 10 ft. Replace a crushed, split or rusted 10 ft section rather than patching it, and clear any clog at the top elbow before you seal anything.
How to replace a section of a downspout?
To replace a section of a downspout, remove the screws and straps above and below the damaged piece, measure the gap plus the overlap at each end, and cut new stock of the same size (2×3 or 3×4 in) and material. Crimp the lower end if the cut removed it, install it crimped end down, drive one 1/2 in screw per side at each joint and re-band at 2 per 10 ft.
My gutter downspout fell off. What can I do to fix it?
Check the gutter outlet first: if the outlet tube is intact, slide the top elbow back over it and drive a 1/2 in self-tapping screw on each side. If the outlet tore out of the gutter, replace the outlet. Then reassemble the run crimped ends down and fasten 2 bands per 10 ft into studs, blocking or masonry anchors, not siding alone.
Should you caulk downspout joints?
Caulk is the second step, not the first. Amerimax joins downspout parts by fitting the larger end over the crimped smaller end and fastening them with sheet metal screws, so a joint assembled crimp-down should not leak. If a correct joint still drips, use a gutter sealant such as Geocel 2320, which is rated for joints no larger than 1/4 in by 1/4 in.
How many straps does a downspout need?
A downspout needs 2 straps, or bands, per 10 ft section under Amerimax’s metal gutter instructions, so a 20 ft two-story drop gets 4. K&M Sheet Metal sets them about 1 ft from the top and 1 ft from the bottom of a 10 ft run, and says 3 usually suffice on a straight 20 ft run with one at the joint.