Subscribe

COST & ESTIMATES · November 20, 2026

14 Ft Metal Roofing Price (2026): Per Panel, Per Sq Ft and Fit

14 ft metal roofing price: $36.82 to $88.63 per panel (Nov 2026), with coverage, pitch fit and panel counts for a 12x14 shed and 24x28 garage.

14 Ft Metal Roofing Price (2026): Per Panel, Per Sq Ft and Fit

By The Roofing Brief Team | Last reviewed: November 2026

The 14 ft metal roofing price runs $36.82 to $88.63 per panel at the U.S. suppliers checked in November 2026, before screws, trim, delivery or labor. The cheapest sheet per square foot of roof was not the cheapest sheet per piece: a 26 gauge Galvalume PBR panel at $42.84 covers 42 sq ft ($1.02 per sq ft), while a $36.82 corrugated sheet covers only 24.9 sq ft ($1.48 per sq ft).

Salvaged sheets only beat these prices below a per-sheet break-even, worked out in our guide to used metal roofing.

A 14 ft sheet is the length that roofs a 12 ft deep lean-to shed with overhangs at 3:12 and a 24 ft wide gable garage at 4:12 without an end lap, which is why it sells as a stock size at MG Building Materials, Menards and The Home Depot. The prices below sit in the same series as our 12 ft metal roofing price guide, our 16 ft metal roofing price guide and our 20 ft metal roofing price guide.

What does a 14 ft metal roofing panel cost?

A 14 ft metal roofing panel cost $36.82 for 29 gauge Galvalume corrugated, $42.84 to $44.80 for 26 gauge Galvalume R-panel or PBR, and $56.48 to $88.63 for painted 29 gauge rib panels at the sellers below. The last column divides each price by the panel’s net coverage, which is the number to compare.

Stack of 14 ft ribbed Galvalume steel roofing panels on wood blocks at a supply yard
Ribbed panels with 36 in of net coverage cover 42 sq ft per 14 ft sheet. AI-generated illustration.
14 ft panel Gauge and finish Price per panel Net coverage Per sq ft of roof Source (as listed November 2026)
24 in x 14 ft corrugated (SKU 1134) 29 ga Galvalume $36.82 21-1/3 in (24.9 sq ft) $1.48 MG Building Materials, San Antonio, Nov 20, 2026
39 in x 14 ft PBR panel (SKU 1111) 26 ga Galvalume $42.84 36 in (42 sq ft) $1.02 MG Building Materials, Nov 20, 2026
5-V Roofing 14 ft, 02775 (SKU 874) 29 ga Galvalume $43.68 24 in (28 sq ft) $1.56 MG Building Materials, Nov 20, 2026
R-Panel cut to 14 ft (RP-GALV-26) 26 ga Galvalume, AZ55, 0.0185 in $44.80 ($3.20 per linear ft) 36 in (42 sq ft) $1.07 Ironrod Steel, Houston, Nov 20, 2026
R-Panel cut to 14 ft, Matte Black or Light Stone 26 ga painted $58.10 ($4.15 per ft) 36 in (42 sq ft) $1.38 Ironrod Steel color listings, Nov 20, 2026
R-Panel cut to 14 ft, Polar White 26 ga painted $61.46 ($4.39 per ft) 36 in (42 sq ft) $1.46 Ironrod Steel color listings, Nov 20, 2026
36 in x 14 ft Pro-Rib (precut) 29 ga painted $56.48 everyday 36 in (42 sq ft) $1.34 Menards, last read Oct 29, 2026
Gibraltar 14 ft SM-Rib, White (model 987612) 29 ga Galvalume, painted $69.98 36 in (42 sq ft) $1.67 The Home Depot listing, Nov 2026
Gibraltar 14 ft SM-Rib, Tan (model 987667) 29 ga Galvalume, painted $88.63 36 in (42 sq ft) $2.11 The Home Depot listing, Nov 2026

MG Building Materials and Ironrod Steel prices were read on their product pages on November 20, 2026. The Home Depot and Menards block automated page reads, so the Home Depot figures are the per-piece prices its listings showed in November 2026 search results, other SM-Rib colors listed above $100, and the Menards figure is its October 29, 2026 everyday price. Home Depot also lists a Metal Sales 3 ft x 14 ft Pro-Panel II (model HD2594114 in Galvalume, HD259W214 in Chestnut Brown) with no online price shown, and the Lowe’s ribbed panels we found online (Union MasterRib, Metal Sales Classic Rib) were 8 ft and 12 ft lengths. Big-box prices are set by store ZIP code, so enter yours before comparing.

At yards that price by the foot, 14 ft carries no length premium. MG’s 14 ft corrugated works out to $2.63 per linear ft, the same as its 16 ft sheet of the same panel at $42.08 (SKU 1135), and Ironrod cuts any whole-foot length at $3.20 per ft. MG’s 26 gauge PBR at $3.06 per ft even undercuts its own 29 gauge 5-V at $3.12 per ft, so do not assume the thinner sheet is the cheaper one.

How much roof does one 14 ft panel cover?

One 14 ft panel covers 42 sq ft when the profile has 36 in of net coverage, 28 sq ft as a 24 in 5-V sheet and 24.9 sq ft as MG’s 21-1/3 in corrugated. That makes the same 14 ft length worth 1.69 times more roof in a rib panel than in lapped corrugated.

Every 36 in panel in the price table earns its 42 sq ft from a maker or seller spec: Ironrod lists a 36 in cover width with 1.25 in ribs at 12 in on center, Gibraltar’s help center says each SM-Rib panel covers a 3 foot wide section once installed, and Metal Sales prints 36 in coverage for both Classic Rib and Pro-Panel II. MG lists its 14 ft corrugated as a 24 in sheet that covers 21-1/3 in and its 5-V at 24 in of cover. More profiles are in our metal roof panel widths and coverage guide. Spans and slope limits for both shapes are compared in our ribbed vs corrugated metal roofing guide.

Will a 14 ft panel reach from ridge to eave?

A 14 ft panel covers a horizontal run of 13 ft 6 in at 3:12, 13 ft 2.4 in at 4:12 and 12 ft 5.4 in at 6:12, overhangs included. The table divides 167 in (168 in of panel less a 1 in drip past the fascia) by each pitch’s slope factor.

Roof pitch Slope factor Sloped length of a 14 ft horizontal run Longest horizontal run one 14 ft panel covers Panel rule at this pitch
1:12 1.0035 14.05 ft 13 ft 10.4 in Lapped panels need sealant (IRC R905.10.2)
2:12 1.0138 14.19 ft 13 ft 8.7 in Lapped panels need sealant
3:12 1.0308 14.43 ft 13 ft 6.0 in Classic Rib and Pro-Panel II minimum
4:12 1.0541 14.76 ft 13 ft 2.4 in All exposed-fastener profiles above
5:12 1.0833 15.17 ft 12 ft 10.2 in All
6:12 1.1180 15.65 ft 12 ft 5.4 in All
8:12 1.2019 16.83 ft 11 ft 6.9 in All
12:12 1.4142 19.80 ft 9 ft 10.1 in All

The 3:12 row is why 14 ft is the shed length: a 12 ft deep lean-to leaves 18 in for overhangs, enough for 12 in at the low eave and 6 in at the high side. At 6:12 the same 12 ft depth leaves only 5.4 in, so a steeper shed needs 15 or 16 ft sheets. Framing and wall flashing for that shed type are in our metal roof on a lean-to guide.

Section R905.10.2 of the 2021 International Residential Code sets the slope floor: lapped, nonsoldered metal panels need 3:12 without applied lap sealant and 1/2:12 with sealant applied per the maker, while standing seam goes to 1/4:12. Makers can be stricter. Metal Sales lists a 3:12 minimum for Classic Rib and Pro-Panel II and says Classic Rib panels “cannot be endlapped,” so a run longer than the table allows calls for a longer cut, not two sheets lapped together. Our metal roofing panel lengths guide lists factory minimum and maximum cut lengths.

How many 14 ft panels does a shed or garage need?

A 12 x 14 lean-to shed at 3:12 needs 5 panels of 36 in coverage, a 24 x 28 gable garage at 4:12 needs 20, and a 24 x 36 carport at 3:12 needs 26. Each count divides the eave length plus both rake overhangs by the panel coverage and rounds up; the fit column uses the pitch table above.

Backyard lean-to shed with a low-slope silver ribbed metal roof overhanging the front wall
At 3:12, one 14 ft panel spans a 12 ft deep lean-to with up to 18 in of combined overhang. AI-generated illustration.
Building (Roofing Brief worked example) Pitch and overhangs Sloped length needed Does 14 ft fit? 36 in panels 5-V (24 in) / corrugated (21-1/3 in)
12 x 14 lean-to, slope across the 12 ft depth 3:12; 6 in front and back, 6 in rakes 13 ft x 1.0308 + 1 in = 13 ft 5.8 in Yes, 6.2 in to trim 15 ft / 3 ft = 5 8 / 9
12 x 14 lean-to with 12 in overhangs front and back 3:12 14 ft x 1.0308 + 1 in = 14 ft 6.2 in No, 6.2 in short; order 15 ft Not priced Not priced
12 x 14 gable shed, ridge along 14 ft 4:12; 6 in eaves and rakes 6.5 ft x 1.0541 + 1 in = 6 ft 11.2 in per side Yes: cut each 14 ft sheet into two 7 ft pieces, 0.8 in spare 5 sheets (10 pieces) 8 / 9 sheets
24 x 28 garage, gable, ridge along 28 ft 4:12; 12 in eaves and rakes 13 ft x 1.0541 + 1 in = 13 ft 9.4 in Yes, 2.6 in spare 30 ft / 3 ft = 10 per side, 20 total 30 / 34
24 x 28 garage, gable 5:12; 12 in eaves 13 ft x 1.0833 + 1 in = 14 ft 2.0 in No, 2 in short; order 15 ft Not priced Not priced
24 x 36 carport, gable 3:12; 12 in eaves and rakes 13 ft x 1.0308 + 1 in = 13 ft 5.8 in Yes, 6.2 in spare 38 ft / 3 ft = 13 per side, 26 total 38 / 44

The 24 x 28 garage shows how tight the length is: the same building at 5:12 comes up 2 in short, and Metal Sales’ install guide names the eave overhang as one of the two critical panel measurements, adding that small variances can usually be taken out at the eave or peak ends, not a 2 in shortfall. Measure the rafter run on the building, not the plan, before you order. For other footprints, our metal roofing calculator runs the same count, and our gable roof shed guide covers shed pitches and rafter sizes.

What does a 14 ft metal roof cost in materials?

Panels alone for the 24 x 28 garage at 4:12 cost $856.80 to $1,399.60 at the November 2026 prices above, or $1.04 to $1.70 per sq ft of its 822 sq ft roof. The 12 x 14 lean-to runs $214.20 to $349.90 in panels.

Panel choice (price per 14 ft sheet) 12 x 14 lean-to, 3:12 (201 sq ft roof) 24 x 28 garage, 4:12 (822 sq ft roof) Garage per sq ft of roof
MG 26 ga Galvalume PBR ($42.84) 5 = $214.20 20 = $856.80 $1.04
Ironrod 26 ga Galvalume R-Panel ($44.80) 5 = $224.00 20 = $896.00 $1.09
Ironrod 26 ga Matte Black R-Panel ($58.10) 5 = $290.50 20 = $1,162.00 $1.41
MG 29 ga Galvalume corrugated ($36.82) 9 = $331.38 34 = $1,251.88 $1.52
MG 29 ga Galvalume 5-V ($43.68) 8 = $349.44 30 = $1,310.40 $1.59
Home Depot Gibraltar SM-Rib, White ($69.98) 5 = $349.90 20 = $1,399.60 $1.70

Roof areas are Roofing Brief arithmetic: the garage is 30 ft of eave plus rakes times 13 ft of run times the 4:12 factor of 1.0541, times 2 sides; the lean-to is 15 ft times 13 ft times 1.0308. The bill leaves out ridge cap, rake and eave trim, closures, butyl tape and underlayment, because those counts depend on the trim profile you pick.

Hired out, the 2026 Roofing Cost Report puts exposed-fastener metal at $6 to $10 per sq ft installed, or about $4,932 to $8,220 for the 822 sq ft garage. The $857 to $1,400 panel bill is 10% to 28% of that range, and labor is most of the rest: the BLS OEWS May 2025 release puts the U.S. median roofer wage at $26.65 per hour. Whole-house pricing by profile is in our metal roof cost guide.

How much does a 14 ft panel weigh, and what does gauge buy?

A 14 ft, 36 in coverage panel weighs about 26.0 to 26.5 lb in 29 gauge and 33.2 to 33.6 lb in 26 gauge, using the weight per square foot Metal Sales prints for Pro-Panel II and Classic Rib times 42 sq ft. The 20 panels for the 24 x 28 garage weigh 521 to 672 lb before screws and trim.

Panel and gauge Weight per sq ft One 14 ft panel 20-panel garage order Allowable load at 2 ft supports Source
Pro-Panel II, 29 ga 0.62 psf 26.0 lb 521 lb 88 psf inward Metal Sales Pro-Panel II sheet
Pro-Panel II, 26 ga 0.79 psf 33.2 lb 664 lb 114 psf inward Metal Sales Pro-Panel II sheet
Classic Rib, 29 ga 0.63 psf 26.5 lb 529 lb 97 psf inward Metal Sales Classic Rib data (1-2026)
Classic Rib, 26 ga 0.80 psf 33.6 lb 672 lb 125 psf inward Metal Sales Classic Rib data
Classic Rib, 24 ga 1.05 psf 44.1 lb 882 lb 139 psf inward Metal Sales Classic Rib data
Union MasterRib, 29 ga / 26 ga Not listed Not listed Not listed 112 / 150 psf live at 24 in spans Union MasterRib spec sheet

Ironrod lists its 26 gauge R-panel at 0.0185 in and 29 gauge at about 0.0142 in, so 26 gauge is roughly 30% thicker, and the load columns rise 29% to 34% between the two gauges on all three makers’ tables. Union’s sheet caps roof purlin spacing at 2 ft on center for MasterRib, the spacing every load in the table assumes. Our 26 vs 29 gauge metal roofing comparison covers the trade-off in more depth, and our roof purlins guide covers spacing and sizes.

How many screws does a 14 ft panel take?

Plan on about 34 panel screws per 14 ft, 36 in panel: Metal Sales’ Post-Frame Install Guide says 80 screws per square are typical for 3 ft wide panels, and one 14 ft panel is 0.42 square. A 2 ft wide 5-V sheet takes about 12 at the guide’s 40 per square.

On 2 ft purlins, a 14 ft panel crosses 8 support lines (the eave, 6 intermediate purlins and the ridge), so 34 screws averages just over 4 per line. Metal Sales also places side-lap stitch screws 12 in on center on roof panels, which adds 14 per side lap on a 14 ft run. The 20-panel garage therefore needs about 680 panel screws plus about 252 stitch screws across its 18 side laps (9 per slope) (Roofing Brief arithmetic). Metal Sales’ guide says to apply enough torque to seat the washer and not to overdrive the fastener.

Getting 14 ft panels home

A 14 ft panel hangs 6 ft past the tailgate of an 8 ft pickup bed and 8.5 ft past a 5.5 ft bed. Both exceed the 4 ft rear overhang at which Texas Transportation Code 547.382 requires a red flag at least 12 in square, and other states set their own trigger, so check your state code before loading.

Metal Sales’ handling rules say no more than 1/3 of a panel’s length should be left unsupported when lifting, which is 4 ft 8 in on a 14 ft sheet, and that individual panels can be carried by people placed every 6 to 8 ft, holding the sheet on edge. That is 2 people for one 14 ft sheet if each stands about 3 ft in from an end, or 3 at 7 ft spacing. A 14 ft trailer deck or yard delivery avoids the overhang; Ironrod quotes about $200 for delivery within greater Houston. To trim the 6.2 in off a lean-to panel, use snips or shears, not an abrasive wheel; our guide to cutting metal roofing covers the tools.

How to order 14 ft metal roofing without waste

  1. Measure the horizontal run from the ridge (or high wall) to the outside of the fascia, then add the eave overhang you want, 6 to 12 in in the examples above.
  2. Multiply by your slope factor (1.0308 at 3:12, 1.0541 at 4:12, 1.0833 at 5:12) and add 1 in for the drip past the fascia.
  3. If the result is 168 in (14 ft 0 in) or less, 14 ft stock works; between 168 and 192 in, buy 16 ft stock or a cut length rather than lapping two sheets.
  4. Count panels: eave length plus both rake overhangs, divided by net coverage (3 ft for rib panels, 2 ft for 5-V, 1.78 ft for 21-1/3 in corrugated), rounded up, then doubled for a gable.
  5. Pick gauge: 29 gauge on 2 ft purlins for sheds and carports, or 26 gauge where loads are higher (150 vs 112 psf live at 24 in on MasterRib), then price both, since MG’s 26 gauge PBR costs less per foot than its 29 gauge 5-V.
  6. Add 34 screws per 36 in panel, 14 stitch screws per side lap, ridge cap and closures, then price delivery: 20 panels in 26 gauge weigh about 664 to 672 lb.

Which 14 ft panel should you buy?

If your situation is Then buy Why (source)
Lean-to shed, 12 ft deep, 3:12 or 4:12, overhangs totaling 18 in or less (14 in or less at 4:12) 14 ft stock rib panel Covers 13 ft 6 in of run at 3:12 and 13 ft 2.4 in at 4:12 (pitch table)
Garage or barn up to 24 ft wide, 4:12 or flatter, 12 in eaves 14 ft panels, 10 per side per 30 ft of eave 13 ft 9.4 in needed vs 14 ft (worked example)
Same building at 5:12 or steeper 15 or 16 ft panels or a cut length 14 ft 2.0 in needed at 5:12; Classic Rib cannot be endlapped (Metal Sales)
Lowest material cost per sq ft of roof 26 ga Galvalume PBR or R-panel at a metal yard $1.02 to $1.07 per sq ft (MG, Ironrod, Nov 2026)
Color has to match a house or garage 26 ga painted R-panel or 29 ga painted rib panel $58.10 to $61.46 at Ironrod; $56.48 Menards Pro-Rib; $69.98 and up at Home Depot
Roof below 3:12 PBR / R-panel with lap sealant, or standing seam IRC R905.10.2: 1/2:12 lapped with sealant, 1/4:12 standing seam
Tempted by the cheapest sheet Compare per sq ft, not per piece $36.82 corrugated costs $1.48 per sq ft vs $1.02 for $42.84 PBR
Short-bed pickup only Yard delivery or a 14 ft trailer 8.5 ft overhang on a 5.5 ft bed vs the 4 ft flag trigger (Tex. Transp. Code 547.382)

Exposed-fastener rib profiles by name, with their specs, are in our MasterRib guide and our 5V metal roofing guide, and our Metal Sales review covers the maker behind Classic Rib and Pro-Panel II.

Frequently asked questions

How much is a 14 ft piece of metal roofing?

A 14 ft piece of metal roofing cost $36.82 to $88.63 at U.S. sellers in November 2026. MG Building Materials listed 29 gauge Galvalume corrugated at $36.82 and 26 gauge Galvalume PBR at $42.84, Ironrod Steel cut 26 gauge R-panel at $44.80, and Home Depot listed Gibraltar 14 ft SM-Rib at $69.98 (White) and $88.63 (Tan).

How many square feet does a 14 ft metal roofing panel cover?

A 14 ft panel with 36 in net coverage covers 42 sq ft. A 24 in 5-V sheet covers 28 sq ft, and a corrugated sheet that covers 21-1/3 in once lapped, like MG’s 14 ft 29 gauge panel, covers about 24.9 sq ft.

How much does a 14 ft sheet of metal roofing weigh?

A 14 ft, 36 in coverage sheet weighs about 26.0 to 26.5 lb in 29 gauge, 33.2 to 33.6 lb in 26 gauge and 44.1 lb in 24 gauge, based on the 0.62 to 1.05 psf weights in Metal Sales’ Pro-Panel II and Classic Rib data sheets multiplied by 42 sq ft.

What is the price of 16 foot corrugated metal roofing?

MG Building Materials listed its 26 in x 16 ft, 29 gauge Galvalume corrugated sheet (SKU 1135, covers 21-1/3 in) at $42.08 on November 20, 2026, the same $2.63 per linear ft as its 14 ft sheet. Our 16 ft metal roofing price guide compares more 16 ft panels.